Planet MGSW SERIES User manual

Managed Metro Ethernet Switch
MGSW/MGSD Series
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring DC Power Inputs .............................................................................. 5
4. Terminal Setup ........................................................................................... 6
4.1 Logging on to Console ......................................................................... 7
 4.2 ConguringIPAddress......................................................................... 8
 4.3 StoringCurrentSwitchConguration..................................................... 9
5. Starting Web Management .........................................................................10
 5.1 LoggingintotheManagedMetroSwitch ..............................................10
 5.2 SavingConguration...........................................................................13
6. RecoveringBacktoDefaultConguration.....................................................14
7. Customer Support .....................................................................................15

3
1. Package Contents
Thank you for purchasing PLANET L3 and L2+ Managed Metro Ethernet Switches.
Thedescriptionsofthesemodelsareshownbelow:
MGSW-28240F L324-port100/1000BASE-XSFP+4-port10GSFP+Managed
MetroEthernetSwitch
MGSW-24160F L2+16-port100/1000BASE-XSFP+8-portGigabitTPManaged
MetroEthernetSwitch
MGSD-1008F L2+8-port100/1000XSFP+2-port10/100/1000TManaged
MetroEthernetSwitch
“Managed Metro Switch” is used as an alternative name in this Quick
InstallationGuide.
Open the box of the Managed Metro Switch and carefully unpack it. The box
shouldcontainthefollowingitems:
ModelName
Package Item MGSW-28240F MGSW-24160F MGSD-10080F
TheManagedMetroSwitch 
QuickInstallationGuide 
RJ45 to RS232 Console Cable 
Rubber Feet 
Two Rack-mounting Brackets
withAttachmentScrews 
PowerCord 
Dust Caps RJ45 593
SFP 28 16 8
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
zWorkstations running Windows 10/XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerialPortConnection(Terminal)
The above workstations come with COM port (DB9) or USB-to-RS232
converter.
 The above workstations have been installed with terminal emulator, such as
TeraTerm,PuTTYorHyperTerminalincludedinWindowsXP/2003.
 Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedMetroSwitch.
zEthernetPortConnection
 Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
 The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explorer 8.0 or above to access
the Managed Metro Switch. If the Web interface of the Managed
Metro Switch is not accessible, please turn off the anti-virus soft-
wareorfirewallandthentryitagain.

5
3. Wiring DC Power Inputs
The Front Panel of the Managed Metro Switch indicates a DC inlet power socket
and consists of one terminal block connector within 6 contacts. Please follow the
steps below to insert the power wire.
1 3 5 7
2 4 6 8
RingPWR
DC 1 Owner
DC 2
Fault
ACTLNK
ACTLNK
1000
100
RESET
10
9
MGSD-10080F
2
1
4
3
6
5
8
7
10
Console
115200,N,8,1
9
100~240V AC
50/60 Hz
ON
AC POWER
OFF
DC POWER
ON
DC Input Range 36V~60V
OFF
Fault
GNDGNDDO 1DO 0DI 1DI 0
DC 2DC 1
V1+ V2+
Figure 3-1: MGSD-10080F Switch Front Panel
100~240V AC
50/60 Hz
ON
OFF
DC POWER
ON
OFF Reset
10 12 14 16
9 11 13 15
18 20 22 24
17 19 21 23
2 4 6 8
1 3 5 7
ACT1000 LNK ACT10/100 LNK
Console
115200, N, 8, 1
18 20 22 24
2Fault
DC1
DC2
PWR
4 6 8 10 12 14 16
17 19 21 23
1 3 5 7 9 11 13 15
MGSW-24160F
Fault
GNDGNDDO1DO0DI 1DI 0
DC 2DC 1
DC Input Range: 36V~60V DC
Please refer to user’s manual before
connect the DC wire.
CAUTION
Figure 3-2: MGSW-24160F Switch Front Panel
100~240V AC
50/60 Hz
ON
AC POWER
OFF
DC POWER
ON
OFF
Ring R.O.
FaultFAN2
FAN1
PWR
DC 2
DC 1
DC Input Range:
36V~60V
2 4 6 8 10 12 14 16 18 20 22 24 26 28
272625242322212019181716151413121110987654321 28
Console
Reset
115200, N, 8, 1
Fault
GNDGNDDO1DO0DI 1DI 0
DC 2DC 1 1 2 3 4
2 4
MGSW-28240F
Figure 3-3: MGSW-28240F Switch Front Panel
Tighten the wire-clamp screws for preventing the wires from loosening.
1 2 3 4 5 6
V1+ V1- V2+ V2-
Power 1 Power 2
Positive(+)Pin Negative(-)Pin
ManagedMetroSwitch Pin 1 / 5 Pin 2 / 6
Note
The wire gauge for the terminal block should be in the range from
12 to 24AWG.

6
4. Terminal Setup
Tocongure the system,connectaserialcableto aCOMport onaPCornotebook
computerandtotheDB9typeofserialportoftheManagedMetroSwitch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: Managed Metro Switch Console Connectivity
A terminal program, such as Tera Term or PuTTY, is required to make the software
connectiontotheManagedMetroSwitch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud:115200
Databits:8
Parity:None
Stopbits:1
Flowcontrol:None
Figure 4-2: COM Port Conguration

7
4.1 Logging on to Console
Oncetheterminalisconnectedtothedevice,powerontheManagedMetroSwitch,
and the terminal will display “running testing procedures”. Then, the following
message asks to log in user name and password. The factory default user name
andpasswordareshownasfollowsandtheloginscreeninFigure4-3appears.
Username:admin
Password:admin
Figure 4-3: Managed Metro Switch Console Login Screen
The user can now enter commands to manage the Managed Metro Switch. For a
detaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new
passwordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.

8
4.2 ConguringIPAddress
TheManagedMetroSwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
ShowingtheCurrentIPAddress
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure4-4.
Figure 4-4: IP Information Screen
ConguringIPAddress
3.At the “#” prompt, enter the following command and press <Enter> as shown
in Figure 4-5.
MGSW-28240F#congureterminal
MGSW-28240F(cong)#interfacevlan1
MGSW-28240F(cong-if-vlan)#ipaddress192.168.1.100 255.255.255.0
Figure 4-5: Conguring IP Address Screen

9
The previous command would apply the following settings for the Managed Metro
Switch.
IPAddress:192.168.1.100
SubnetMask:255.255.255.0
4.Repeatstep1tocheckiftheIPaddressischanged.
If the IP is successfully congured, the Managed Metro Switch will apply the new
IP address setting immediately. You can access the Web interface of the Managed
MetroSwitchthroughthenewIPaddress.
4.3 StoringCurrentSwitchConguration
In the Managed Metro Switch, the running conguration sequence running-cong
can be saved from the RAM to FLASH by “copy” command, so that the running
conguration sequence becomes the start-up conguration le, which is called
congurationsave.
Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-cong startup-cong
Figure 4-6: Saving Current Conguration Command Screen
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.

10
5. Starting Web Management
The following shows how to start up the Web Management of the Managed
Metro Switch. Note the Managed Metro Switch is congured through an Ethernet
connection. Please make sure the manager PC must be set to the same IP subnet
address.
For example, the default IP address of the Managed Metro Switch is
192.168.0.100, then the manager PC should be set to 192.168.0.x (where x
is a number between 1 and 254, except 100), and the default subnet mask is
255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.100
Figure 5-1: IP Management Diagram
5.1 Logging in to the Managed Metro Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100(thefactorydefaultIPaddressortheonethatyouhave
justchangedinconsole)toaccesstheWebinterface.
2.When the following dialog box appears, please enter the default user name and
password “admin” (or the password you have changed via console). The login
screen in Figure 5-2 appears.