Plantronics EXPLORER 210 Series User manual

Plantronics Explorer®210 Series
User Guide

1
Package Contents and Features
Plantronics Explorer®210 Series Accessories*
Headset Front
AC Charger
100–240V
* Not included. To order, please contact your Plantronics supplier or go
to www.plantronics.com
Headset Back
Vehicle Charging Adapter
#76777-01
USB Headset Charger
#76016-01
Vehicle Power Charger
#78583-01
Power on/off
Call control button
Indicator light
Volume control
Earloop
Microphone
Speaker/eartip
Charging jack

2
How to Charge Your Headset Using the AC Charger
Before using your headset for the first time, charge it for at least
20 minutes. A full charge takes approximately two hours.
1 Connect the AC charger to a power outlet.
2 Plug the AC jack into the charging jack on the headset.
While your headset is charging, the indicator glows red. When your
headset is fully charged, the indicator turns off. Do not use your headset
while it is connected to the charger.
NOTE Never charge the battery where the temperature may fall below
0°C (32°F) or rise above 40°C (104°F) – for example, in an unattended
motor vehicle. Do not charge the battery while it is unattended.
Charging Your Headset
CHARGING TIME
2 hours ...................
Full charge
20 minutes ..............
Minimum charge
before first use
1
2

3
Pairing Your Headset
Pairing is the process of introducing your headset to your phone.
Before using your headset for the first time, you must pair it with
your Bluetooth phone. Normally, you need to pair your headset with
your phone only once.
Plantronics QuickPair™Technology
Your new headset includes Plantronics QuickPair technology to simplify
the Bluetooth setup process. The first time you turn your headset on,
your headset automatically enters pairing mode for 10 minutes (the
indicator light flashes red and blue). Once paired successfully, your
headset stays on for instant use.
If not successfully paired after 10 minutes, your headset automatically
goes to standby mode. When you turn the headset off then on again,
it automatically goes into pairing mode until successfully paired with a
Bluetooth phone.

4
1
How to Pair Your Phone With Your Headset for the First Time
1 Turn on the Bluetooth feature on your phone.
For most phones, select Settings/Tools > Connections >
Bluetooth > On. See your phone’s user guide for more information.
2 Turn the headset on.
Turn on your headset by sliding the power switch forward. Wait until
the indicator light flashes blue and red.
If you don’t see the red/blue flash,turn the headset off, wait, then
turn it on again. Wait until you see the red/blue flash.
3 Use the commands on your phone to locate your headset.
For most phones, select Settings/Tools > Connections > Bluetooth >
Search > 2XXPlantronics. See your phone’s user guide for
more information.
4 When prompted for the passkey, enter 0000.
Pairing is successful when the indicator on your headset flashes
blue. Your headset is now connected and ready to use.
Pairing Your Headset – First Time
3
SET TING S
SET TING S
Time and Date
Phone Set tings
Bluetooth
Sound Set tings
Networ k Services
Security
Reset Set tings
BLUE TOO TH
BLUE TOO TH
Discover/
Search
8BK; JEEJ >
8BK; JEEJ >
(N NFbWdjhed_Y i
PASS KE Y
0000
2
4

5
Pairing Your Headset
How to Pair Your Headset if it Has Been Previously Paired
With Another Device
1 Turn the headset off.
Slide the power switch off, then wait until the indicator turns red
and then turns off.
2 Turn the headset on.
Slide the power switch on. After the headset is powered on, press
and hold the call control button until the indicator light continues to
flash red and blue.
3 Use the commands on your phone to locate your headset.
For most phones, select Settings/Tools > Connections > Bluetooth
> Search > 2XXPlantronics. See your phone’s user guide for
more information.
4 When prompted for the passkey, enter 0000.
Pairing is successful when the indicator on your headset flashes
blue. Your headset is now connected and ready to use.
4
3
BLUE TOO TH
BLUE TOO TH
Discover/
Search
8BK; JEEJ >
8BK; JEEJ >
(N NFbWdjhed_Y i
PASS KE Y
0000
2
1

6
1 To remove the earloop, gently pull up on earloop near the
Plantronics name until you hear a snap.
2 Position earloop as shown above, then gently snap back
onto post.
3 Place the earloop behind your ear.
4 Rotate the headset so that the speaker/eartip rests
comfortably in your ear.
5 Align the microphone with the corner of your mouth.
Callers can hear you best when you point the microphone towards
the corner of your mouth.
Adjusting the Fit
Right Left
2
1
3
4
5

7
Headset Controls
Turn on the headset Slide the power switch on, then wait until the
indicator glows blue. You will hear ascending tones.
Turn off the headset Slide the power switch off, then wait until the
indicator glows red. You will hear descending
tones. When power is off, indicator stays off.
Answer a call Briefly press the call control button.
When you receive a call, your phone may ring
before your headset rings. Wait until you hear
the ring in your headset before you press the call
control button to answer the call.
Reject a call When phone rings, press and hold the call control
button until you hear a single low tone.
Make a call Enter number on your phone, press send, and
the call is automatically transferred to headset;
no need to press call control button.
Adjust the volume Tap the volume + button to increase volume.
At the upper limit you will hear two tones. Tap -
button to decrease volume level. (There are eight
volume levels.)
WARNING Do not use headphones/headsets
at high volumes for an extended period of time.
Doing so can cause hearing loss. Always listen
at moderate levels. See www.plantronics.com/
healthandsafety for more information on headsets
and hearing.

8
Range
To maintain a connection, keep your headset within 10 metres (33 feet)
of the Bluetooth device. If there are obstacles between your headset and
the device, you may experience interference. For optimal performance,
place your headset and phone on the same side of your body.
Audio quality degrades as you move out of range. When you are far
enough away to lose the connection, you hear a high tone in the headset.
NOTE The headset attempts to reconnect for 30 seconds. If you move
back in range after 30 seconds pass, you can manually reconnect by
pressing the call control button.
NOTE Audio quality is also dependent upon the device with which the
headset is paired.
Headset Controls
Transfer a call from
headset to phone
While in a call, press and hold the call control
button until you hear a single low tone.
Transfer a call from
phone to headset
While in a call, press and hold the call control
button until you hear a single low tone.

9
Indicator Lights
Headset Status Headset Indicator Light
Powering on Steady blue, then intermittent flashes
(changes to standby mode)
Powering off Red appears and goes off
Standby Blue intermittent flashes
Charging battery Red solid light. Light indicator turns off when
battery is fully charged and headset is off.
Low battery Triple red flashes
Pairing mode Blue/red alternating flashes
Missed call Purple flashes. Press the call control button
to cancel flashing light.
Incoming call Triple blue flashes when ringing.