Polyaire ZoneMaser ZoneTouch V2 User manual

ZoneTouch V2
Zone Control System
User Manual
www.polyaire.com.au
©2014 Polyaire Pty Ltd

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - User Manual
II

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - User Manual 1
1) Features 2
2) Wall Controller Layout (Touch Screen) 3
3) Manual Group Control 4
3.1 Group On/Off/Turbo 4
3.2 Adjusting airflow for a group 5
4) Automated Group Control 5
4.1 Set Program 6
4.2 Select Program for a Group 7
5) User Settings 8
5.1 Time/Date setup 8
5.2 Owner’s Name 9
5.3 Turbo Group 9
5.4 Temperature Display 10
5.5 Touch Tone 10
6) Information Sheets 11
7) Troubleshooting Guide 14
8) Specifications 15
TABLE OF CONTENTS
Liability
Please read the instructions before installing this Zonemaster Zoning Control System.
Polyaire Pty Ltd does not accept any responsibility for loss or damage that may occur as a result of the incorrect
installation of this Zonemaster Control System.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - User Manual
2
1) Features
 • Userfriendlylargetouchscreeninterface
 • Intuitiveuserinterface
 • Controlairowtoindividualzones1and groups2
 • ColourLCDforclearerdisplay
 • Personalizedsystemsettingsandlabelling
 • Wallmountedwithuptotwotouchscreensavailableinasystem
 • 5-1-1ProgrammableOn/Otimeprograms
 • Oneselectableturbo3group to cool/heat a particular area quicker
 • Halfyear,OneyearandTwoyearservicereminderstocalltechnicianforcleaning
andservicingACsystem4.
 • Allzonesautomaticallyresumetheiroriginalon/ostateoncepowerisrestored
afterpoweroutage.
1. A zone is the area where air supply is controlled by one motorized damper
2. A group is a few zones grouped together which have the group name and are controlled (turning on and
o,oradjustingopeningpercentage)atthesametime.Agroupwillhaveatleastonezoneandnomore
than four zones.
3. Turbo function will give the selectedgroupafull-openingwhileallothergroups’(dampers)opening
positions are reduced by 50% of their open percentage value. This will bring a large volume of extra air
into the designated area and cool or heat the area quicker.
4. AC system is the ducted air conditioner which has ZoneTouch V2 as its zone control system.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - User Manual 3
2) Wall Controller Layout (Touch Screen)
The home screen of the system willnormallydisplaygroups’status,dampers’open
 percentagewithadjustingbuttons,date,time,roomtemperature,touchtonestatus
 andZoneTouchlogoasshowninFigure1.
NOTE:
 • The touch screen will go to the sleep mode after 90 seconds of inactivity.
In sleep mode, the screen is blank. Touching any area of the screen will
activate the system.
 • To clean the touch screen, use a dry, soft cloth and very gently wipe the
screen. If necessary, dampen the cloth with distilled water or with an
equal ratio of distilled water to white vinegar.
Home Screen (Figure 1)

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - User Manual
4
3) Manual Group control
3.1  GroupOn/O/Turbo
a) Onthehomescreen,touchagroupbutton(Figure2)tochangetheon/o
groupstatusandthedampersofthegroupwillopenorcloseaccordingly.
b) Thegroupstatuscanbesetto‘TURBO’activewhenthegroupisspecied
asaturbogroup(referto5.3)andthegreyturboindicatorwillturnblueto
    indicatetheTURBOfunctionisactive.Figure3showsthegroupstatus
sequence alternated by touching the group button.
c)Upto6groupbuttonsareshowninonescreenandtouch<or >to bring up
    previousornextpage.
Figure 2
Figure 3

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - User Manual 5
4) Automated Group Control
 Automatedon/ocontrolforeachgroupisanimportantfeatureoftheZoneTouchV2
 system.Thissystemhasthreeprogramscenarios,oneforweekdays(Mondayto
 Friday),oneforSaturdayandoneforSundayrespectively.
Eachprogramscenariohas4programmableeventsperday:ontime1,otime1,on
 time2andotime2.Eachprogrameventcanbeenabledanddisabledandthetime
 canbeadjustedasdesired.Allfoureventsaredisabledinthefactorydefaultwith
 settingsaslistedinthetablebelow.Userscancreateupto4programsusingthe
 scenariosanddierenteventtimeslots.
NOTE: A group can have up to a maximum of 4 zones. Your installer would
have already set up your zones and groups.
3.2 Adjustingairowforagroup
•Thedamperopeningpercentageforeverygroupcanbeadjustedtocontrol
theamountofairowateveryoutletbetween10%and100%ofthebalanced
value(setupbyInstaller)at10%increments.
   • Touch or buttons on the home screen to increase or decrease the
percentage opening for the corresponding group.
•TheairowwillbeunadjustableiftheTurbofunctionisactive.Pressing
andwillnotchangetheopeningpercentage.
NOTE: The Turbo function cannot be programmed. It is activated manually from
the touch screen as needed.
On time 1 O time 1 On time 2 O time 2
Monday to Friday 6.30AM 8.00AM 5.30PM 10.00PM
Saturday 7.30AM 12.30PM 6.00PM 11.30PM
Sunday 7.30AM 12.30PM 6.00PM 11.30PM

4.1 Set Program
Uptofourprograms can be created.
Touchingbuttonwillgobackto
the home screen from programming setting pages.
a) Touch Program buttons (e.g. )on‘programming’screen(Figure4)
toenterthescreen(Figure5)toselectscenariosandadjusttheeventtimes.
ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - User Manual
6
Touch the button on the home screen
toenter‘Programming’screen(Figure4).
Figure 4.
Figure 6.
b) TouchadayoptionradiobuttontoselectMonday-Friday,Saturdayor
    Sundayprogramtomodify.Touchthetimeswitchradiobuttonontheright
toenable/disableON/OFFtime.
c) Touchthehour,minuteorAM/PM
eldonthescreentohighlightit,
and then the and buttons
    willappearonthescreen(Figure6).
Touchorbuttonstoadjust
the time.
NOTE: Afteranediteldis
   highlighted,touchingthateldagain
will quit from the editable status and
the and will disappear.
Figure 5

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - User Manual 7
Figure 7.
4.2 Select Program for a Group
Enterthe‘Assignment’screen(Figure
7) by touching on
   programmingscreen(Figure4).
   Assignmentscreenshowsthelistof
the current program of each group.
Touchingbuttonwillgobackto
thehomescreenfromAssignment
page.
Figure 8.
Figure 9.
Figure 10.
   Touchtheprogrameldofagroupto
showallprogramoptions(Figure8).
   Touchingaprogramoptionwillassign
theprogramtothegroup(Figure9).
Eachgroupcanbeassignedwithone
program from program1 to program4
(‘P1’to‘P4’),andthegroupwillnot
haveaprogramif‘No’isselected.Ifa
program has been assigned to a group,
theprogramindicatorwillappearon
thegroup(Figure10)ifanyofthefour
eventsintheprogramisenabled.
NOTE: Programs cannot be
assigned to a group with turbo
status. Record programs and groups
to ‘Table 5: Programs’ on Page 13

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - User Manual
8
a) Touch on the home screen
(Figure1)enter“Settings”screen
(Figure11)
b) Touch to enter ‘user
settings’screen(Figure12)
InUserSetting,youcansetupdate
andtime,owner’sname,Turbogroup,
temperature display and touch tone.
Touchingbuttonwillgobackto
thehomescreenfromUsersetting
pages.
Figure 11.
Figure 12.
5) User Settings
Figure 13.
Figure 14.
5.1 Time/Date setup
a) Touch on the‘User
Settings’screen(Figure12)toenter
the time/date setup screen
(Figure13).
   b) Hour,Minute,AM/PM,day,month
andyeareldswillbeshownonthe
    screen.Touchtheeldwhichneed
tobemodied,thentouchor
buttontochangethevalue
(Figure14).
c) Touch buttontosavethe
    changesandgobacktoUser
Setting page.