Potter Amseco EBP-401 User manual

SPK
CHIME SEL.
OUTPUT
OU TPU T
INPUT
12V AC
12V AC
GND +12V
GND +12V
EBP-401
LONG RANGE DOOR
ANNUNCIATOR SYSTEM
Potter Electric Signal Company • 2081 Craig Road, St. Louis, MO, 63146-4161 • Phone: [phone]/Canada 888-882-1833 • www.amseco-kai.com
MKT. #8850053 - REVA
5/06 PAGE 1 OF 2
PRINTED IN USA
A Brand
• Intelligent microprocessor driven system
• 40 ft. detection range across doorway
• Four user selectable chime sounds
• Advanced circuit integrated with active-infrared
beam technology
• High/low volume control
• Expandable using additional chimes (CM-5)
Stock Number - 4130030
The EBP-401 is a surface mount, 40 ft., long range annunciator system using active infrared technology. This invisible single infrared
beam triggers a pleasant chime sound when the infrared beam is interrupted. The system can be installed anywhere inside the buildings
where traffic surveillance is required.
Complete Kit Includes:
1 Electronic chime
1 Infrared sensor
1 Reflector
1 Power transformer (12VAV 20VA)
1 Long plastic bracket
1 Metal short bracket
1 Short plastic bracket
1 6 ft. power cord with in-line switch
1 26 ft. 2-conductor wires
6 3/4” sheet metal screws
1 3/8” bolt w/locking washer
2 5/8” machine screws w/washers and nuts
1 Manual
2~3
Feet
Min.
Power ON/OFF
Switch
Electronic
Chime Infrared
Sensor 26 ft Wires Power Transformer
(12VAC 20VA)
Reflector Long Plastic
and Short
Metal
Mounting
Bracket
Short
Mounting
Bracket
6 ft Power Cords
With In-line ON/
OFF Switch
Hardware
Wiring Diagram
EBPT-401
Transformer
Power
Switch
CM-5
GND: White/Black
+12V :White
Downloaded from Elcodis.com electronic components distributor

MKT. #8850053 - REVA
5/06 PAGE 2 OF 2
PRINTED IN USA
A Brand
Specifications
EBP-401
LONG RANGE DOOR
ANNUNCIATOR SYSTEM
Part Information EBP-401
Description Long Range Wired Annunciator System
Detection method Active infrared
Detection range 40 ft.
Maximum transmission range 1000 ft. AWG#22 2P wire
Power source Sensor: 12VAC/DC, 20VA
Chime: 12V DC, 10VA
Power consumption: Standby Sensor: 50mA
Chime: 100mA
Power consumption: In alarm Sensor: -
Chime: 500mA
Volume level 80dB (low) - 95dB (high)
Chime sounds selection Selectable among 4 sounds by a dip SW
Chime sounds level selection JP1 (Jumper SHORT LOW
Jumper OPEN HIGH)
Response time 4m sec.
Light source Infrared pulse beam 950mm
Installation location Indoor
Infrared beam interception warning Sensor: JP1 selectable
OFF/10 sec/60 secretary
Install setting Transformer Power ON - Red Alignment LED ON - Transformer
Power OFF - Transformer Power ON - Setting
Power switch Yes
Temperature 14°F - 122°F (-10°C - 50°C)
Weight
Dimension: (W x H x D)
Sensor: 125g
Chime: 164.4g
Sensor: 2 1/2” x 1 7/8” x 3 7/16”
Chime: 4 7/8” x 3 1/2” x 1 3/8”
Installation
Reflector
ALIGNMENT LED LIGHTS UP
WHEN THE REFLECT OR
ALIGNMENT IS SUCCESSFUL.
3/8" Bolt
5/8" Screw
Metal Short Bracke
t
NutNut
Short Plastic Bracket
Locking
Washer
Rear Mount Side Mount
Lock Washer
Screw
Lock Washer
Screw
If necessary, use cable
ties to keep wires safely
out of the way to avoid
tripping.
Downloaded from Elcodis.com electronic components distributor