Power Electronics SD700FL Series User manual

Low Harmonics Notch Filter
Hardware and Installation Manual
FL

Variable Speed Drive
Hardware and Installation Manual
Edition: December 2012
SD7FLMTHW02AI Rev. A

SD700FL SERIES
POWER ELECTRONICS
2

POWER ELECTRONICS
SD700FL SERIES
3
SAFETY SYMBOLS
Always follow safety instructions to prevent accidents and potential hazards from occurring.
Edition of December 2012
This publication could present technical imprecision or misprints. The information here included will be
periodically modified and updated, and all those modifications will be incorporated in later editions.
To consult the most updated information of this product you might access through our website
www.power-electronics.com where the latest version of this manual can be downloaded.
WARNING
This symbol means improper operation may results in serious personal
injury or death.
CAUTION
Identifies shock hazards under certain conditions.Particular attention should
be given because dangerous voltage may be present. Maintenance
operation should be done by qualified personnel.
Identifies potential hazards under certain conditions. Read the message and
follow the instructions carefully.
Identifies shock hazards under certain conditions.Particular attention should
be given because dangerous voltage may be present.

SD700FL SERIES
POWER ELECTRONICS
4
Revisions
Date Revision Description
14 / 12 / 2012 A First edition

POWER ELECTRONICS
SD700FL SERIES
INDEX
5
INDEX
SAFETY INSTRUCTIONS........................................................................................................... 7
1. INTRODUCTION .................................................................................................................. 11
2. CONFIGURATION TABLE & STANDARD RATINGS......................................................... 12
2.1. Configuration Table..................................................................................................... 12
2.2. Standard ratings –400Vac ......................................................................................... 13
2.3. Standard ratings –690Vac ......................................................................................... 14
3. TECHNICAL CHARACTERISTICS...................................................................................... 15
4. RECEPTION, HANDLING AND TRANSPORTATION......................................................... 18
4.1. Reception and Storage............................................................................................... 18
4.2. Handling and Transportation....................................................................................... 18
5. MECHANICAL INSTALLATION .......................................................................................... 20
5.1. Environmental ratings................................................................................................. 20
5.2. Drive mounting............................................................................................................ 21
5.3. Clearances.................................................................................................................. 22
5.4. Cooling........................................................................................................................ 23
6. POWER CONNECTION ....................................................................................................... 27
6.1. Basic configuration...................................................................................................... 27
6.2. Topology..................................................................................................................... 28
6.3. Power connection and wiring...................................................................................... 31
6.4. Ground connection...................................................................................................... 35
6.5. EMC Installation Requirements................................................................................... 36
6.6. Protections.................................................................................................................. 38
6.7. IT grids - floating earth drives...................................................................................... 39
6.8. Dynamic Braking Resistors for Equipments of Frames 1 and 2.................................. 40
6.9. Power Terminals of the Freemaq Filter....................................................................... 42
6.10. Power Terminals of the SD700 Drive.......................................................................... 44
6.11. Connection between the Freemaq Filter and the SD700 Drive................................... 55
7. CONTROL CONNECTION................................................................................................... 56
7.1. Wiring recommendations............................................................................................ 56
7.2. Control board terminals description ............................................................................ 57
7.3. Filter control terminals description .............................................................................. 60
7.4. Control connection and configuration.......................................................................... 61
7.5. STO - Safe torque Off................................................................................................. 62
7.6. Connection with ATEX motors.................................................................................... 66
8. MODBUS COMMUNICATION.............................................................................................. 67
8.1. Introduction................................................................................................................. 67
8.2. Hardware technical specifications............................................................................... 68
8.3. RS232 connection....................................................................................................... 69
8.4. RS485 connection....................................................................................................... 69
9. COMMISSIONING................................................................................................................ 70
10. DIMENSIONS....................................................................................................................... 72
10.1. Dimensions of Frames 1 and 2................................................................................... 72
10.2. Dimensions of Frames 3 and 4................................................................................... 73
10.3. Dimensions of Frame 5............................................................................................... 74
10.4. Dimensions of Frame 6............................................................................................... 75
10.5. Dimensions of Frame 7............................................................................................... 76
10.6. Dimensions of Frame 8............................................................................................... 77
10.7. Dimensions of Frame 9............................................................................................... 78
10.8. Dimensions of Frame 10............................................................................................. 79
10.9. Dimensions of Frame 11............................................................................................. 80
11. MAINTENANCE ................................................................................................................... 82
11.1. Warnings..................................................................................................................... 82
11.2. Routine Inspection...................................................................................................... 82

SD700FL SERIES
POWER ELECTRONICS
6
INDEX
12. OPTIONAL EQUIPMENT..................................................................................................... 84
12.1. Accessories................................................................................................................. 84
12.2. Extension Box............................................................................................................. 85
12.3. Plinths......................................................................................................................... 85
12.4. Dynamic Braking Unit B150........................................................................................ 86
12.5. Touch-Graphic Display ............................................................................................... 87
12.6. Communication boards............................................................................................... 87
12.7. IP54 Solutions for Frames 1 to 4................................................................................. 88
12.8. Input Protection Module for Frames 5 to 11................................................................ 88
13. CE MARKING...........................................................................................................................89
13.1. EMC Directive.................................................................................................................89
13.2. Low Voltage Directive.....................................................................................................89
MANUFACTURER’S DECLARATION OF CONFORMITY CE................................................... 91

POWER ELECTRONICS
SD700FL SERIES
SAFETY INSTRUCTIONS
7
SAFETY INSTRUCTIONS
IMPORTANT!
Read this manual carefully to maximise the performance of this product and to ensure its safe use
and installation.
Power Electronics accepts no responsibility or liability for any damage resulting from
inappropriate use of the equipment.
In this manual, safety messages are classified as follows:
WARNING
Do not remove the metal cover while the power is applied or the unit is in operation. Otherwise
electric shock could occur.
Do not run the drive with the front cover removed.
Otherwise, you may get an electric shock due to the high voltage terminals or exposure of charged
capacitors.
The drive does not remove the voltage from the input busbars of the drive. Before working on the
drive, isolate the whole drive from the supply.
Do not remove the cover except for periodic inspections or wiring, even if the input power is not
applied. Otherwise, you may access to the charged circuits and may get an electric shock.
Wiring and periodic inspections should be performed at least 10 minutes after disconnecting the
input power. To remove the front cover check that the DC Link red LED is off, then remove the
terminals metallic cover and check with a multimeter the following measures:
Measure between the output power busbars U, V, W and the cabinet and check that the
voltage is around 0V.
Measure that the DC link terminals +HVDC, -HVDC and chassis voltage is below 30VDC.
Otherwise, you may get an electric shock.
Operate the switches with dry hands. Otherwise, you may get an electric shock.
Do not use cables with damaged insulation. Otherwise, you may get an electric shock.
Do not subject the cables to abrasions, excessive stress, heavy loads or pinching. Otherwise, you
may get an electric shock.
Do not make any insulation or voltage withstand tests on the motor with the drive connected.

SD700FL SERIES
POWER ELECTRONICS
8
SAFETY INSTRUCTIONS
CAUTION
Install the drive on a non-flammable surface. Do not place flammable material nearby. Otherwise
fire could occur.
Disconnect the input power if the drive is damaged. Otherwise, it could result in a secondary accident
or fire.
After stopping the drive, it will remain hot for a couple of minutes. Touching hot parts may result in
skin burns.
Do not apply power to a damaged drive or to a drive with parts missing even if the installation is
complete. Otherwise, you may get an electric shock.
It is not permitted to weld the cabinet; this can damage the electronic sensitive equipment inside.
Do not allow lint, paper, wood chips, dust, metallic chips or other foreign matter into the drive.
Otherwise fire or accident could occur.
WARNINGS
RECEPTION
The SD700FL is carefully tested and perfectly packed before delivering.
In the event of transport damage, please ensure that you notify the transport agency and POWER
ELECTRONICS: 902 40 20 70 (International [phone]) or your nearest agent, within 24hrs
from receipt of the goods.
UNPACKING
Make sure model and serial number of the variable speed drive are the same on the box, delivery
note and unit.
Each variable speed drive is delivered with Hardware and Software technical manuals.
RECYCLING
Packing of the equipments should be recycled. For this, it is necessary to separate different
materials included (plastic, paper, cardboard, wood ...) and deposit them on proper banks.
Waste products of electric and electronic devices should be selectively collected for your correct
recycling company.
EMC
The drive is intended to be used in industrial environment (Second Environment), it achieve
compliance with C3 category defined in IEC/EN 61800-3 standard following the installation
recommendation within this manual.
Select communication and control system according to the drive EMC environment. Otherwise,
systems could suffer from interferences due to a low EMS level.

POWER ELECTRONICS
SD700FL SERIES
SAFETY INSTRUCTIONS
9
SAFETY
Before operating the drive, read this manual thoroughly to gain and understanding of the unit. If
any doubt exists then please contact POWER ELECTRONICS, (902 40 20 70 / [phone]
57) or your nearest agent.
Wear safety glasses when operating the drive with power applied or the front cover is removed.
Handle and transport the drive following the recommendations within this manual.
Install the drive according to the instructions within this manual and the local regulations.
Do not place heavy objects on the drive.
Ensure that the drive is mounted vertically and keeping the minimum clearances distances.
Do not drop the drive or subject it to impact.
The SD700FL drives contain static sensitive printed circuits boards. Use static safety procedures
when handling these boards.
Avoid installing the drive in conditions that differ from those described in the Technical
Characteristics section.
CONNECTION PRECAUTIONS
To ensure correct operation of the drive it is recommended to use a SCREENED CABLE for the
control wiring.
The motor cable should comply with the requirements within this manual. Due to increased
leakage capacitance between conductors, external ground fault protection threshold value
should be adjusted ad hoc.
Do not disconnect motor cables if input power supply remains connected.
The internal circuits of the SD700 Series will be damaged if the incoming power is connected
and applied to output terminals (U, V, W).
Do not use power factor correction capacitors banks, surge suppressors, or RFI filters on the
output side of the drive. Doing so may damage these components.
Always check whether the DC Link red LED is OFF before wiring terminals. The capacitors may
hold high-voltage even after the input power is disconnected.
TRIAL RUN
Verify all parameters before operating the drive. Setting of parameters may be required
depending on application and load.
Always apply voltage and current signals to each terminal that are between levels indicated
within this manual.
OPERATION PRECAUTIONS
When the Auto Restart function is enabled, keep clear of driven equipment, as the motor will
restart suddenly after the fault reset.
The “STOP / RESET” key on the keypad is active only if the appropriate function setting has
been made. Pushing this button the drive will NOT perform a safe stop. It is available STO
optional board, which installed with an external EMERGENCY STOP pushbutton, will disconnect
the motor power supply and will be unable to generate torque in the motor with high reliability.
If a fault is reseted with the reference signal still active, the drive will unexpectedly restart. Verify
that it is permissible for this to happen. Otherwise, it could cause a personal injury.
Do not modify or alter internal wiring and spare parts without Power Electronics supervision.
Before programming or operating the SD700 Series, initialise all parameters back to factory
default values.

SD700FL SERIES
POWER ELECTRONICS
10
SAFETY INSTRUCTIONS
EARTH CONNECTION
Ground the drive and adjoining cabinets to ensure a safety operation and to reduce
electromagnetic emission.
Connect the input PE wire only to the dedicated PE terminal of the drive. Do not use the cabinet
or the chassis screw for grounding.
Ground the drive chassis through the dedicated and labelled terminals. Use appropriate
conductors to comply with the local regulations. The ground conductor should be connected first
and removed last.
Motor ground cable must be connected to the PE output terminal of the drive and not to the
installation‟s ground. We recommend that the section of the ground conductor (PE) should be
equal or greater than the active conductor (U, V, W).
If the user decides to use shielded motor cable, ensure a correct 360º shield bonding in both the
drive cabinet and the motor terminal box.
HOW TO USE THIS MANUAL
Quick Guide
1- Make sure model and serial number of the drive are the same on the delivery note and unit. See
Chapter 2.
2- Read carefully the safety instructions before installation, commissioning, operation and
maintenance of the drive. See safety instructions section.
3- For reception, handling and transportation see Chapter 4.
4- Before the mechanical installation, check the environmental ratings, drive configuration mounting
and clearances. See chapter 5.
5- Follow the mechanical installation instructions. See Chapter 5.
6- Before the electrical installations, check basic configuration and wiring recommendations, see
Chapter 6 and Chapter 7.
7- Follow the electrical installation instructions in Chapter 6 and Chapter 7.
8- For Modbus Communication hardware, see Chapter 8.
9- Follow the commissioning instructions in Chapter 9.
10- For preventive maintenance instructions, follow the recommendations in Chapter 11.

POWER ELECTRONICS
SD700FL SERIES
INTRODUCTION
11
1. INTRODUCTION
SD700 low voltage drives by Power Electronics is the most extensive product family with a power range
from 1.5kW to 2000kW. It has been designed focused on maximum motor care, components durability and
easy maintenance. SD700 portfolio is divided in 3 products series that comply with specific demands and
standards in worldwide installations thanks to its own specific features: SD700, SD700KOMPAKT,
SD700FREEMAQ (SD700FR & SD700FL).
The Freemaq consist of a Notch Filter connected to the input of the SD700 drive in order to reduce the grid
current Harmonic Distortion (THDi). SD700FL drive is not built-in a common passive filter because the grid
impedance modification, the connection of multiple systems or the grid expansion will not reduce the
filtering features and will never cause resonance. Its design is based in the parallel connection of unitary
filter modules. Each module is smartly designed to optimize the space and the internal cooling system. All
of them are managed and controlled without additional hardware by the SD700 drive. SD700 FL is a
compact solution for installations willing to reduce the harmonic distortion. This robust design reduces the
grid current Harmonic Distortion below the 5% as requested by the regulation IEEE519.
Figure 1.1 SD700FL Series
SD700FL products provide high efficiency, maximum control, functional safety, durability, easy
commissioning and easy maintenance for the whole range. Power Electronics delivers flexible integrated
solutions, fully tested under the most demanding environmental and electrical conditions.

SD700FL SERIES
POWER ELECTRONICS
12
CONFIGURATION TABLE AND STANDARD RATINGS
2. CONFIGURATION TABLE & STANDARD
RATINGS
2.1. Configuration table
EXAMPLE
CODE: SD7FL0370526T
SD7
FL
0370
5
2
6
-
-
T
-
SERIE
SD700
Model
Output current [1]
Input Voltage [2]
Degree of
protection [3]
Pulses
number
Cabinet Plinths
EMC Filter
Floating
Earth [5]
Input
Frequency
SD700FL
Low
Harmonics
Notch Filter
0115
115A
5
380-
500VAC
2
IP20
6
6
Pulses
-
Standard
-
Second
Environment
-
Without
floating
earth
-
50Hz
1800
1800A
6
690VAC
5
IP54
20
[4] Total
Height
2000mm
F
First
Environment [5]
T
With
floating
earth
6
60Hz [6]
…
…
22
Total Height
2200mm
M
IT Filter
Optional
GENERAL CONSIDERATIONS:
[1] Verify the rated current of the motor nameplate to guarantee the compatibility with the selected drive.
[2] Consult Power Electronics for different input voltages.
[3] Degree of protection values exposed in the table correspond to the drive. Filters‟ modules degree of protection is
always IP42.
[4] SD700 frame 4 available with 1712mm and 2000mm total height.
[5] Floating earth drive not available with first environment filter.
[6] Consult availability.
CODIFICATION EXAMPLES:
oSD7FL180062620 SD700FL, 1800A, 690Vac, Degree of protection IP20, 6 pulses, 2000mm Height,
Second Environment, Without floating earth, 50Hz.
oSD7FL180062620F SD700FL, 1800A, 690Vac, Degree of protection IP20, 6 pulses, 2000mm Height,
First environment, Without floating earth, 50 Hz.
oSD7FL065055620 SD700FL, 650A, 400Vac, IP54, 6 pulses, 2000mm Height, Second Environment,
Without floating earth, 50Hz.
The following figure shows an example of designation label:
Figure 2.1 Type designation label (located on lateral panel)

POWER ELECTRONICS
SD700FL SERIES
CONFIGURATION TABLE AND STANDARD RATINGS
13
2.2. Standard ratings –400Vac
FRAME
CODE
Operation Temperature 50ºC
HEAVY DUTY
I(A)
Rated
Motor Power
(kW) at 400VAC
150% Overload
(A)
1
SD7FL0006 5 6
6
2.2
9
SD7FL0009 5 6
9
4
14
SD7FL0012 5 6
12
5.5
18
SD7FL0018 5 6
18
7.5
27
SD7FL0024 5 6
24
11
36
2
SD7FL0032 5 6
32
15
48
SD7FL0038 5 6
38
18.5
57
SD7FL0048 5 6
48
22
72
3
SD7FL0060 5 6
60
30
90
SD7FL0075 5 6
75
37
113
SD7FL0090 5 6
90
45
135
SD7FL0115 5 6
115
55
173
4
SD7FL0150 5 6
150
75
225
SD7FL0170 5 6
170
90
255
5
SD7FL0210 5 620
210
110
315
SD7FL0250 5 620
250
132
375
SD7FL0275 5 620
275
150
413
6
SD7FL0330 5 620
330
160
495
SD7FL0370 5 620
370
200
555
SD7FL0460 5 620
460
250
690
7
SD7FL0580 5 620
580
315
870
SD7FL0650 5 620
650
355
975
SD7FL0720 5 620
720
400
1080
8
SD7FL0840 5 620
840
450
1260
SD7FL0925 5 620
925
500
1388
SD7FL0990 5 620
990
560
1485
9
SD7FL1150 5 620
1150
630
1725
SD7FL1260 5 620
1260
710
1890
SD7FL1440 5 620
1440
800
2160
10
SD7FL1580 5 620
1580
900
2370
SD7FL1800 5 620
1800
1000
2700
11
SD7FL2200 5 620
2200
1200
3300
SD7FL2500 5 620
2500
1400
3750

SD700FL SERIES
POWER ELECTRONICS
14
CONFIGURATION TABLE AND STANDARD RATINGS
2.3. Standard ratings –690Vac
FRAME
CODE
Operation Temperature 50ºC
HEAVY DUTY
I(A)
Rated
Motor Power
(kW) at 690VAC
150% Overload
(A)
3
SD7FL0052 6 6
52
45
78
SD7FL0062 6 6
62
55
93
4
SD7FL0080 6 6
80
75
120
SD7FL0105 6 6
105
90
157
5
SD7FL0130 6 620
130
110
195
SD7FL0150 6 620
150
132
225
SD7FL0170 6 620
170
160
255
6
SD7FL0210 6 620
210
200
315
SD7FL0260 6 620
260
250
390
SD7FL0320 6 620
320
315
480
7
SD7FL0385 6 620
385
355
578
SD7FL0460 6 620
460
450
690
8
SD7FL0550 6 620
550
500
825
SD7FL0660 6 620
660
630
990
9
SD7FL0750 6 620
750
710
1125
SD7FL0840 6 620
840
800
1260
SD7FL0950 6 620
950
900
1425
10
SD7FL1140 6 620
1140
1000
1710
SD7FL1270 6 620
1270
1200
1905
SD7FL1420 6 620
1420
1400
2130
11
SD7FL1500 6 620
1500
1500
2250
SD7FL1800 6 620
1800
1800
2700
.

POWER ELECTRONICS
SD700FL SERIES
TECHNICAL CHARACTERISTICS
15
3. TECHNICAL CHARACTERISTICS
SD700FL SERIES
INPUT
POWER RANGE [1]
2.2kW –1800kW
VOLTAGE RANGE [1]
380-500Vac, 690Vac, 3 phases (±10%)
INPUT FREQUENCY [1]
50Hz/60Hz (±6%)
INPUT RECTIFIER TECHNOLOGY
Thyristor-Diode
DISPLACEMENT POWER FACTOR
(DPF = cos Φ )
≥0.99
POWER FACTOR
(PF= I1/Irms· cos Φ)
≥0.98
MOMENTARY POWER LOSS
> 2sec (depending on the load inertia)
EMC INPUT FILTER
Second environment (Industrial): (C3 Standard)
First environment (Domestic): C2 (Optional). C1 consult with Power Electronics
Optional IT filter
HARMONICS FILTER
Notch Filter
CURRENT THD (%)
≤ 5%[2]
REGENERATIVE
NO
OUTPUT
OUTPUT FREQUENCY [3]
0...200% of the motor’s rated frequency
OVERLOAD CAPACITY
150% during 60 sec at 50ºC
EFFICIENCY (At full load)
≥97%
CONTROL METHOD
V/Hz
VECTOR CONTROL
Open Loop: PWM speed / torque control, AVC: speed / torque control
Close Loop (Encoder): PWM speed / torque control, AVC: speed / torque control
CARRIER FREQUENCY
4 to 8kHz –PEWave
OUTPUT DV/DT FILTER
500 to 800V/µs
OUTPUT CABLE LENGTH [4]
USC 300m, SC 150m
DYNAMIC BRAKE
External B150 Dynamic Brake (Frames 1 and 2 integrated)
ENVIRONMENTAL
RATINGS
OPERATION AMBIENT
TEMPERATURE
Minimum: -20°C Maximum: +50°C
STORAGE TEMPERATURE
Minimum: -40°C Maximum: +70°C
ALTITUDE
1000m
POWER ALTITUDE DERATING
>1000m, 1% PN(kW) per 100m; 4000m maximum
AMBIENT HUMIDITY
<95%, non-condensing
DEGREE OF
PROTECTION
FILTER
CABINET
IP20 for frames 1 to 4
IP42 for frames 5 to 11
DRIVE
CABINET
IP20, IP54
VIBRATION
Deflection 0.075mm at 10Hz-57Hz; Acceleration 9.8m/s2at 57Hz-150Hz
HEATING RESISTORS
Optionals
PROTECTIONS
MOTOR PROTECTIONS
Rotor locked, Motor overload (thermal model), Output current limit, Phase current
imbalance, Phase voltage imbalance, Motor over-temperature (PTC signal), Speed limit
Torque limit.
DRIVE PROTECTIONS
IGBT's overload, Input phase loss, Low input voltage, High input voltage, DC Bus voltage
limit, Low DC Bus voltage, High input frequency, Low input frequency, IGBT
temperature, Heat-sink over-temperature, Power supply fault, Drive thermal model,
Ground fault, Software and Hardware fault, Analogue input signal loss (speed reference
loss), Safe stop/Emergency Stop
[1]: Other configuration, consult Power Electronics.
[2]: The harmonics are lower than those in the IEEE519 for Isc/IL
[3]: For operation frequencies higher than 100Hz consult Power Electronics.
[4]: SC: Shielded cable, USC: Unshielded Cable. Follow Power Electronics installation recommendations. For greater cable lengths, consult Power
Electronics.

SD700FL SERIES
POWER ELECTRONICS
16
TECHNICAL CHARACTERISTICS
SD700FL SERIES
HARDWARE
DIGITAL INPUTS
5 programmable, Active high (24Vdc), Isolated power supply
Active high (24Vdc), 1 PTC input, isolated power supply
DIGITAL OUTPUTS
2 programmable changeover relays (250Vac, 8A or 30Vdc, 8A)
ANALOGUE INPUT
2 programmable differential inputs. 0 –20mA, 4 –20mA, 0 –10Vdc and 10Vdc.
(Optically isolated)
ANALOGUE OUTPUTS
2 isolated programmable outputs: 0 –20mA, 4 –20mA, 0 –10Vdc and 10Vdc
ENCODER INPUTS (Optional)
2 differential encoders input. Voltages inputs from 5 to 24Vdc
USER POWER SUPPLY
+24Vdc user power supply ( Max 180mA) regulated and short-circuit protected
+10Vdc user power supply (Max 2 potentiometers R= 1 k ) regulated and short-circuit
protected
I/O EXTENSION BOARD
(Optional)
4 Digital Inputs: Programmable inputs and active high (24Vdc). Optically isolated.
1 Analogue Input: Programmable and differential input.
5 Digital Outputs: programmable multi-function relays.
1 Analogue Output: Programmable outputs in voltage / current.
EXTERNAL POWER SUPPLY
(Optional)
24 V External Power Supply, Fault Relay integrated
COMMUNICATION
STANDARD HARDWARE
USB port
RS232 port
RS485 port
OPTIONAL HARDWARE
Optical fiber
Ethernet
STANDARD PROTOCOL
Modbus-RTU
OPTIONAL PROTOCOL
Profibus-DP
DeviceNet
Ethernet (Modbus TCP)
Ethernet IP
CAN Open
N2 Metasys Gateway
CONTROL PANEL
TYPE
Removable
LENGTH
3 meters and 5 meters (optional)
CONNECTION
RJ45
VISUALIZATION LEDS
LED ON: Control board is energized
LED RUN: Motor receiving power supply
LED FAULT: Flashing displays that a fault has occurred
ALPHANUMERIC DISPLAY
4 lines x 16 characters
Keypad with 6 keys to control and configure the drive, start and stop/reset
Independent memory
COLOUR TOUCH-SCREEN
DISPLAY (Optional)
3,5 " Touch Screen (240x320 pixels) with pen
4Gb MicroSD card | Faults and events log and notification
Quad Band GSM modem integrated to remote start, stop and notification by SMS
Independent memory
Ethernet Switch with two RJ45 connections
Optional 5Vdc external power supply or batteries
DISPLAY INFORMATION
Average current and 3-phase motor current
Average voltage and 3-phase motor voltage
Average input voltage and 3-phase input voltage
3-phase input and output frequency
DC Bus Voltage
Drive Status
Speed, Torque, Power, Power factor of motor
Register of total and partial drive running time with reset function. (hours)
Register of total and partial drive energy consumption with reset function (kWh)
Relay status
Digital inputs / PTC status
Output comparator status
Analogue inputs and sensor values
Analogue output value
Motor overload and equipment status
Drive and rectifier temperature
Fault history (last 6 faults)
OTHERS
Real time clock
Perpetual calendar

POWER ELECTRONICS
SD700FL SERIES
TECHNICAL CHARACTERISTICS
17
SD700FL SERIES
REGULATIONS
CERTIFICATIONS
CE, cTick, UL [5], cUL [5]
ELECTROMAGNETIC
COMPATIBILITY
EMC Directive (2004/108/CE)
IEC/EN 61800-3
IEEE519
DESIGN AND CONSTRUCTION
LVD Directive (2006/95/CE)
IEC/EN 61800-2 General requirements
IEC/EN 61800-5-1 Safety
IEC/EN 60146-1-1 Semiconductor converters
IEC60068-2-6 –Vibration
IEC/EN61800-5-2 Safe Torque Off (STO) certified by Tüv Rheinland
[5]: On certification process.

SD700FL SERIES
POWER ELECTRONICS
18
RECEPTION, HANDLING AND TRANSPORTATION
4. RECEPTION, HANDLING AND
TRANSPORTATION
CAUTION
Read carefully the following instructions for a correct handling.
Otherwise, it could lead to people injury and cause damaged to the equipment.
4.1. Reception and Storage
The SD700FL is carefully tested and perfectly packed before delivering. In the event of transport
damage, please ensure that you notify the transport agency and Power Electronics: 902 40 20 70
(International [phone]) or your nearest agent, within 24hrs from receipt of the goods.
Make sure model and serial number of the drive are the same on the delivery note and unit. Check that
the following documentation is attached:
- SD700FL Hardware and Installation Manual.
- General documentation CD including software and programming manual.
Drive‟s storage should be sun and moisture protected and with an ambient temperature between
-40°C and +70°C, < 95 RH without condensation. It is recommended not pile more than two units.
4.2. Handling and Transportation
Only the transport methods described in this document or in the delivery notes are permissible. Any other
transport method or system could damage the unit.
In the case of SD700FL Frame 1, the drive and the filter are delivered separately, horizontally in two
cardboard boxes.
In the case of SD700FL Frames 2 to 4, the drive and the filter are delivered separately, horizontally,
fastened to a wooden pallet and covered with a wooden box.
Depending on the mean of transport, SD700FL frames 5 to 11 is delivered horizontally or vertically.
When the transport is by land, the SD700FL is delivered vertically, fastened to a wooden pallet and
covered with a cardboard box. When the transport is by air, the SD700FL is delivered horizontally,
fastened to a wooden pallet and covered with a wooden box. When the SD700FL is built-in more than 5
filter modules, the filter modules will be delivered separately from the drive.
Depending on the transport method, the drive could be moisture protected with a vacuum plastic bag.
Move the complete pallet as close as possible to its final installation place before unpacking, to avoid any
damage during transportation.
It is mandatory to transport it with a pallet truck, forklift or crane fork, taking care about the load
distribution and centre of gravity. Check the size and weight of the equipment to choose proper lifting
equipment with a capacity greater than the drive weight.
Unpack the drive carefully. Do not use edge tool to protect the product from damage. After open the
package, please check the goods contained. Verify the item numbers contained within the package with
the packing inventory list. Please set aside and reserve, if contained, the case of spare parts shipped
with the product. There should be no evident damage caused by vibration, dropping or moisture.
CAUTION
If the maximum tonnage of cranes cannot meet the requirement, it could lead to people injury and
cause damage to the equipment.