Power House M 8539 User manual

LCD display,7-stage switch mode
2-4-8-12 charging current
AUTO
%
M 8539
Imported and distributed by Altronic Distributors Pty. Ltd.
www.altronics.com.au
Made in China

RISK OF EXPLOSION
Only connect the battery leads when the mains supply is disconnected.
Explosive gases may escape from the battery during the charging process.
Prevent flames and sparks and provide adequate ventilation during charging.
Indoor use only.
Unplug the charger from the mains before breaking or making the connection to
the battery.
Not suitable for use with non-rechargeable batteries.
In addition to the battery types and capacity detailed in the specifications,the
charger is suitable for the following only:
Charging only a single battery at any one time
Charging rechargeable lead acid, Gel, EFB, AGM or calcium batteries
with 6 cells
Th Smart Charger automatically adjusts the charge rate applied as the
battery charges. With the battery fully charged the charging process stops, as
the battery naturally discharges further charge is applied until the battery is
again fully charged. This is an ongoing process to ensure a safe connection for an
indefinite period.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
The charger contains no serviceable replaceable parts.
Not for commercial use.
1Safety
2
AC Plug
Battery clips
2Contents
Instructions
3Features
12.4
LCD Dis play
Navigation Keys
LCD Display
AutoCharge/ Memory Saver
Standard lead acid vehicle setting(14.4v)
Start Stop (AGM) vehicle setting (14.6v)
Fault / Incorrect Polarity
1
2
3
4
5
6
Navigation Keys
MEM
Memory
Saver
AUTO
CHARG E
Stan dard
Vehld e
START
STOP
Star t/stop
Vehid e
3
1
2
3
4
5
6
is

%
TEST
%
A
KA
V
AUTO
CCA
EN
!
Bat tery Vol tage
Charging
Current
Fault
Codes
12 . 4 8. 0 F 0 1
%
Performance/
completion
!
Fault
Reverse Polarity
Battery
Capacity EN
Battery
Capacity CCA
AUT O
CHA RGE
OK Check Low/Bed
Charging &
malntenance modes Maintenance charge Winter charge Repair
Charging Modes
%
Battery
Voltage
Battery
Capacity
Battery
Start Power
Alternator
output
Testing Modes
1234567
Amps(A) Volts(V)
Sta nda rd
Vehlde
START
STO P
Start/stop
Vehi de
Battery Charging
SET
Charging &
malntenance modes Maintenance charge
Repair Winter charge
1.
2.
3.
4.
5.
. .
.
.
.
. .
.
.
.
.
.
.
.
.
+ +
+ +
. . . +
.
.
.
.
.
.
.
.
.
.
.
.
4 5
4Features
5Charging stager
7Operation- Battery Charging
6Connection
Normal Battery
Charging
Maintainance
Charging
Winter
Charging
Battery
Recondition
Start/Stop
Vehicles
Standard
Vehicles
√*（Up to 12A）√（0.8）√ √ √√*

%
Battery
Voltage
Battery
Capacity
Battery
Start Power
Alternator
output
Battery Anatysing
TEST SET
%
Pressing theAuto Charge function will automatically apply the fastest charge rate the battery connected can safely take.
With this mode selected`AUTO`is displayed on the LCD display
Charging is complete when 100% is displayed on the LCD screen
Battery Charging Mode
For standard battery charging at temperatures over 5C
Increases the battery voltage to 14.4v(standard vehicle)or 14.6v (start/stop vehicle).
。
Winter Mode
Used for charging batteries at low temperatures(-20C to +5C). Increases the battery voltage to 14.6v
(standard vehicle) or 14.8v(Start/Stop vehicle).
Recondition Mode
Applies a controlled increased charging voltage to allow recovery of deeply discharged batteries
Maintenance Mode
Applies to low 0.8A charging rate, ideal for long term seasonal connection
1.Press the navigation arrows to select the battery charging icon and press SET.
*Default charging modes
Battery analysing modes operate with and without AC mains supply. Connecting the battery clips to the battery
automatically activates the charger
2.Press the navigation arrows to select the required charging mode and press SET.
Pressing EXIT at any stage takes you to the first stage of the menu process.
Battery Voltage Battery Start Power Alternator Output Battery Capacity
√* √√ √
Battery Voltage mode
Displays the battery voltage as a %of its capacity:
Press the navitgation arrows to select the battery % icon and press SET.
12.7v-100% 12.4v-80% 12.2v-60% 11.9v-40% 11.6v-20%
12.5v-90% 12.3v-70% 12.1v-50% 11.8v-30% 11.3v-10%
%SET
+
1.
Battery Start Power
Assesses battery cranking power and recovery. Measures the voltage drop during engine starting to identify potential
starting problems due to battery failure.
SET
+
1.
2.
3.
4.
A1+ With A1 displayed press SET - measures static battery voltage
A2+ With A2 displayed start the vehicle engine.
Min battery voltage recorded during cranking displayed and good, check or bad status displayed
Good>8v, check 7-8v and bad <7v
SET
A
Assesses battery caranking power and recovery. Measures the voltage drop during engine starting to identify potential
starting problems due to battery failure.
SET
1. + = A1 displayed
2. (Rev engine to 3000rpm*)+ Maintain revs during 10 second countdown
SET
3. A2 displayed(Rev engine to 2000rpm**)+ Maintain revs during 10 second countdown
SET
4. Battery voltages then displayed for both 3000rpm and 2000rpm tests
Good or bad status displayed
* 3000rpm with no battery loading. i.e. no lights AC, etc
**2000rpm with battery loading. i.e. no lights AC, etc
8Operation- Battery Charging
9Operation- Battery Analysing
6
10 Operation- Battery Analysing
7
4.
5.

Battery Capacity
.
SET
1. +
2. +CCA or EN+ Set the battery standard CCA or EN***
3. +CCA/EN value+ input the battery CCA or EN value***
***markings on a battery will state the battery standard and value
If CCA or EN values not stated, select CCA and use the following table
CCA
1000-1299cc 300 CCA
1300-1599cc 400 CCA
1600-1999cc 500 CCA
1600-1999cc 500 CCA
2000-2999cc 700 CCA
3000-3500cc 800 CCA
4. Actual battery value is displayed plus capacity %
Good, check or bad status displayed
Good>74%, check 50-74% and bad <50%
This function will not operate if the battery voltage is less than 8v
Memory Saver
The memory saver function allows the vehicle electrical and audio settings to be retained when the battery is removed.
1. Connect the SmartCharge battery clips to positive(+) and negative(-) cables on the vehicle that attached to
the battery terminals
2. With the AC mains power connected press the Auto Charge button for 5 seconds. Memory Saver mode is
activated when MEM is displayed on the LCD display
3. Remove the vehicle battery
4. Ensure the vehicle battery is connected correctly before disengaging the SmartCharger to ensure no loss of
Vehicle / audio settings
AUT O
CHARGE
AUT O
CHARGE
5 Seconds
Code Detail Reason Action
F01
F01
Battery voltage below 12v
after charging for 300mins
If after 20 hours(five times in Recondition
mode) due to a faulty battery, the
battery does not enter the float stage
Battery is defective
or Load maybe connected to the battery
Battery is sulphated
beyond reconditioning
Replace the battery
Disconnect load from the battery
Replace the battery
F02
Battery voltage too high Battery rated above 12v Check the battery rating
F03
Actual charging rate
exceeds the charge rate set
Charger error
or Interference from another device
Disconnect the charger and the AC supply, then
reconnect, if error happens again charger faulty
Turn off/ disconnect other devices
that may caues interference.
F04
Charger temperature too high High ambient temperature
or Poor ventilation
Select a lower charging current to charge
Allow the charger to cool for 30mins
Ensure enough space for adequate
ventilation(10cm clearance)
F05
Does not enter float stage within 24hrs Charge current too low
or Load maybe connected to a battery
or Battery is defective
Disconnect battery and AC supply.
Reconnect and select a higher charging rate
Disconnect load from battery
Replace the battery
F06
Reverse polarity Battery clips connected incorrectly
Re-connect the battery clips correctly
Check regulator
Poor functioning regulator
F07
Measured charging voltage is too
high during the alternator test
F08
Measured charging voltage is too
low during the alternator test
Belt maybe loose
or Poor functioning alternator
Check belt and alternator
Input Voltage AC
Charging Voltage
Charging Current
Types of Battery
Dimensions
Weight
200-240VAC, 50Hz
14.4v(winter 14.6v)- Standard vehicle
14.6v(winter 14.8v)- START/STOP(AGM)
Up to 12A Max
Lead acid, Gel, Calcium, AGM, EFB
14-220Ah (Charging)
195x138x78
1.51Kg
11 Operation- Battery Analysing
Operation- Memory Saver
Operation- Fault Codes
14
Specifications
8 9
SET
SET
12
13