Power Max TDM-98 User manual

TDM-98
Treadmill User Manual
OWNER’S MANUAL
Read all instructions carefully before using this product. Retain this owner's manual
for the future's reference. Product may be slightly different with photos, it is subject
to actual product. Thank you for purchasing the product.

www.powermaxfitness.net
2
TABLE OF CONTENTS
WARRANTY
2
PRODUCT BRIEF
3
SECURITY PRECAUTIONS AND WARNINGS
4
INSTALLATION INSTRUCTIONS
7
USING INSTRUCTIONS
9
ROUTINE MAINTENANCE
13
1 YEAR LIMITED WARRANTY
PowerMax Fitness warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it has
been installed and operated in accordance with PowerMax Fitness's Owner's Manual. PowerMax
Fitness's obligation under this warranty is limited to replacing or repairing, free of charge, any
parts which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application. From the date of
purchase, the frame is warranted to be free from defects for 1(one) year*.
Customer Care
Phone: [phone]
Email: [e-mail]
Support / Complaint Generation: support.powermaxfitness.net
This warranty is extended only to the original owner and is not transferable.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase
* Terms and Conditions Apply. For T&C visit www.powermaxfitness.net

www.powermaxfitness.net
3
1. PRODUCT BRIEF
A. Single function home use treadmill:
Main Parameters and Parts List
Main Technical Parameters
No.
Parameters Names
Description
1
Input power voltage
AC 220-240V(50/60Hz)
2
Speed
1.0-10 Km/h
3
Running surface
400*1100 mm
4
Expand dimensions
1330*615*1025mm
5
Functions (Option)
Running(massager)

www.powermaxfitness.net
4
Packing List
No.
Name
Units
Qty
1
Complete machine
set
1
2
Accessory Bag
pc
1
3
Base supporting frame
set
1
4
Massager (Option)
pc
1
Accessory Bag List
No.
Name
Qty
No.
Name
Qty
1
Inner hexagon spanner 5mm
1
6
MP3 cable
1
2
Combination wrench
1
7
ScrewM8*25
2
3
Safety key
1
8
Screw M6*12
4
4
Silicone oil
1
5
Manual
1
2. SECURITY PRECAUTIONS AND WARNINGS
Tips: Before folding the treadmill, make sure that the gradient is "zero".
Notice: Please read the instructions carefully before use.
⚫Indoor using and storing the treadmill, avoid dampness, and can not be spilled by water.
⚫Please wear suitable clothes and sneakers before exercise. Prohibited to exercise on the
treadmill barefoot.
⚫High power plug must be grounded, electric outlet should have a dedicated circuit, do not
share with other electrical equipment.
⚫Keep children away from the machine to avoid accidents.
⚫Avoid too long time and overload operation, otherwise will cause motor and controller
damaged, and will accelerate the deterioration of bearing, running belt and running board.
⚫Should maintain machine on a regular basis.
⚫Keep machine away from dust to avoid strong static.
⚫Please cut the electric power off after using.
⚫Please maintain good ventilation when running.
⚫Please clamp security lock cable on your clothing to make sure the machine stops at
emergency condition.
⚫If you feel not very well when using this machine, please stop and consult a doctor.
⚫Silicone oil must be kept away from children after use.
⚫If power cord is damaged, please contact our qualified maintenance personnel for service
rather than disassemble it at your own discretion.

www.powermaxfitness.net
5
Forbidden
⚫Don't use the machine in the status of the shell break in or break off （the internal structure
exposed）or under the condition of welding-parts may fall off.
---- Otherwise an accident or injury may happen.
⚫Don't jump up and down in the process of movement.
---- May be injuries caused by the fall.
⚫Don't keep machine in or near moist space such as the bathroom.
⚫Don’t place machine in direct sunlight, or high temperature places such as near a stove
or a heating appliance.
----Otherwise may cause the leakage and burst into flames.
⚫Don't use when the power cord is damaged or power plug pin is loose.
----Otherwise will lead to an electric shock, short circuit or fire.
⚫Don't damage or bent by force or reverse the power cord. Don’t place heavy objects on
machine, don't clamp the power line.
----Otherwise will cause fire or get an electric shock.
⚫Don't use machine for more than 2 people at the same time, and don't get close to the
machine when it is in use.
---- Or it may be an accident or injury due to falls.
⚫People who can’t express their consciousness or can’t operate the machine by
themselves cannot use the treadmill.
----May occur accident or injury.
⚫Avoid drinking water or pouring water when operation.
---- May cause electric shock and fire. Forbidden!
⚫People who seldom do exercise shouldn't suddenly do intense exercise.
⚫After eating or when feel tired, do not use machine.
---- May lead damage to your health.
⚫This product is suitable for family use, does not apply to schools, gymnasium and so on. -
--There is the danger of injury.
⚫Don’t use when hard objects are in pants pockets.
----May cause accident or injury.
⚫Don’t use when the power plug is on the needle, garbage, or water.
----May cause electric shock, short circuit, or fire. Do not use with wet hands!
⚫when not in use, pull out the power plug from the socket.
----The dust and moisture can age the insulation, and result in leakage fire.
!

www.powermaxfitness.net
6
⚫This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible
for their safety.
⚫Children should be supervised to ensure that they do not play with the appliance.
Ground protection system!
⚫This product must be grounded. If the machine is dysfunctional, grounding will provide a
good channel for electric current, in order to reduce the electric shock risk.
⚫This product is equipped with power plug with grounding conductor and plug. Completely
insert the plug to standard socket.
⚫If the equipment grounding conductor’s connection is improper, it will cause electric
shock. If you have doubts about whether your product is grounded correct or not, please
entrust professional to check.
⚫Please use the socket which has the same shape with the grounding plug. Don’t use plug
adapter.
This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved, children shall not play with the appliance, cleaning and user
maintenance shall not be made by children without supervision.
!

www.powermaxfitness.net
7
3. INSTALLATION INSTRUCTIONS
When installing, simple fix all screws first, then tighten the screws when the installation of frame
is done.
1. Put the machine flat on the ground. Remove the knob with the direction shown in the
picture bellow. Then stand the columns and console with the direction shown in the
picture bellow.
2. Remove the preinstalled screws M8*22 on the supporting frame and then tighten the
supporting frame with screw M8*22 on the base. Use 5# hexagon wrench and screw
M6*12 to lock and fix the base (two screws for each side).
3. Hold left& right columns, use 6# hexagon wrench and screw M8*25 to lock the console
frame on the columns (Tighten all screws in above steps, and please notice not to clamp
the cable by column).
M6*12
M8*22
M8*2
5

www.powermaxfitness.net
8
4. Use the knob in step one to lock the main base and columns (Rotate clockwise, please
refer to the arrow point direction). Uneven ground may cause trouble when rotate the
knob, please lift the column slightly to left side (as shown below). In order to fold the
machine easily next time, please don’t rotate the knob too tight.
Above are steps of single function installation, multifunctional machines need to be
installed after you complete the steps above and then continue with the following
installation:
5. Put the safety key on the picture showing yellow area, then press the start button to start
the treadmill. (Notice: The treadmill can only start when the safety key is put on the yellow
area on the console.
Note: please confirm that all screws are locked uniformly according to the requirements after
installation, and check no part is left out before plug on.
Safety
key
is
in
red
colour.
Please
find
it
in
the
accessory
bag.

www.powermaxfitness.net
9
Folding instructions
When the treadmill is not in use, you can lift the running deck, then use knob to lock the running
deck and base frame as bellow.
4. USING INSTRUCTIONS
❖Plug in power plug properly and turn on the switch (in red colour) (1). When the light is
on, there will be beep sound, and then the screen will light up.
❖Please keep the safety key away from children when the treadmill is not in use. Please put
the silicon oil bottle in places children cannot reach. If it is eaten or split into eyes by
mistake, please use water to wash and consult doctor immediately.
❖Safety key Introduction
The treadmill can only start when the safety key is put on the yellow area of
the console. Clip the safety key on clothes when using the treadmill to
prevent accidents. Put the safety key back when continue using the
treadmill.
❖Console instructions Overlay:
Button instructions
Start-up Normally starts after 3 seconds of countdown.
Programs 1 manual program, 12 automatic programs, 3 modes Safety key function
Disconnect the safety key, "E7" shows on the screen. The treadmill stops gradually, and a
Di alarm sound is let out. Put the safety key back, all the data will be cleared in 2 seconds.
Under any circumstance, the treadmill will stop when disconnect the safety key. There will
be prompt information on the screen. Put back the safety key, screen data will be back to
the initial interface.
1

www.powermaxfitness.net
10
1. Start button, Stop button：
When the power is on, press the start button to start the treadmill. Stop button: when the
treadmill is in running state, press stop button, all data will be cleared, and the treadmill
gradually comes into a complete stop and returns to the manual mode.
2. Program button
In standby mode, pressing this key can cycle the options from manual mode to P1 to P12
automatic programs. Manual mode is the system defaulting running mode.
3. Mode button
In standby mode, press this key can cycle the options of 3 different countdown running
mode: time countdown running mode, distance countdown running mode and calorie
countdown running mode.
4. Volume ± rotary knob
When connect with mobile phone, rotate the knob clockwise to turn the volume up and
rotate counter clockwise to turn the volume down.
5. Speed ± key rotary knob
Use these keys to adjust the speed of the treadmill. Rotate clockwise to increase the
speed and rotate counter clockwise to decrease the speed. You can also press the knob
to adjust the speed directly by 3.0km/h ,6.0km/h and 9.0km/h.
Display Function
a. Speed Display
Display the current running speed value.
b. Time Display
Display the time of manual mode and the countdown time under automatic modes and
programs.
c. Distance display
Display cumulative distance under manual mode and programs. Display the distance
countdown in automatic mode.
d. Calorie display
Display cumulative calorie under manual mode and programs. Display the calorie
countdown in automatic mode.
e. Heart rate display
Heart rate value will be shown when the signal is detected.

www.powermaxfitness.net
11
Automatic Program
Each program is divided into 10 segments, and the running time of each segment of the
program is evenly distributed. Following is a form of time distribution of 12 programs.
3Modes Parameter Setting
The initial setting of time countdown is 15 minutes. The initial setting of calorie countdown is 50
kcal. The initial setting of distance countdown is 1.0 kilometres. Cycle order: time, distance and
calorie.
Time
Programs
1
2
3
4
5
6
7
8
9
10
P1
SPEED
3
3
6
5
5
4
4
4
4
3
P2
SPEED
3
3
4
4
5
5
5
6
6
4
P3
SPEED
2
4
6
8
7
8
6
2
3
2
P4
SPEED
3
3
5
6
7
6
5
4
3
3
P5
SPEED
3
6
6
6
8
7
7
5
5
4
P6
SPEED
2
6
5
4
8
7
5
3
3
2
P7
SPEED
2
9
9
7
7
6
5
3
2
2
P8
SPEED
2
4
4
4
5
6
8
8
6
2
P9
SPEED
2
4
5
5
6
5
6
3
3
2
P10
SPEED
2
5
7
5
8
6
5
2
4
3
P11
SPEED
2
5
6
7
8
9
10
5
3
2
P12
SPEED
2
3
5
6
8
6
9
6
5
3
Set time / 10 = running time of each period

www.powermaxfitness.net
12
Translation of Error Codes
Error
Code
Description
Solution
E1
Communication Abnormal:
when the power is on, the
connection between lower
controller and the console is
abnormal.
Possible Cause:
The communication between the lower controller and
console is blocked, check each joint between the
controller and console, ensure that each core is fully
plugged in.
Check the connection line, replace it if it’s damaged.
E2
No signal from motor.
Possible Cause:
Check the motor cable to see whether it is connected
well or not, if not, connect the motor wire again.
Check the motor cable to see whether it is damaged
or has a burnt smell, if yes, replace the motor.
Check the speed sensor to see whether it is correctly
installed or damaged.
E5
Over current protection:
In working, the lower controller
detects the current to be over 6A
for more than 3 seconds.
Possible Cause:
Overloading leads to excessive current, and the
system stop out of self-protection, or some part is
stuck, causing the motor to stop.
Adjust the treadmill and restart it.
Check if there is liquid or burnt smell while the motor
is running, if yes, replace the motor.
Check if the controller has a burned smell, if yes,
replace the controller.
Check the power supply voltage, if it does not match
the specifications, change into correct voltage and
test the machine again.
E6
Explosion-proof impact protection:
The abnormal voltage or motor
cause the faulty of circuit that
drive the motor.
Possible Cause:
Check if the power supply voltage is 50% lower than
normal voltage.
use the correct voltage and test the machine again.
check if the controller has a burnt smell and replace
the controller.
Check if the motor cable is connected and connect
the motor wire again.
E7
No safety key
Put the safety key on the right place.

www.powermaxfitness.net
13
5. ROUTINE MAINTENANCE
Warning: Before cleaning or maintaining products, please be sure the power plug of the
treadmill is pulled out.
Cleaning: Comprehensive cleaning will extend the using life of the electric treadmill.
Remove dust periodically in order to keep the parts clean. Be sure to clean running belt with
both sides of the exposed portion, which will reduce the accumulation of impurities. Make sure
to wear clean athletic shoes to avoid carrying the dirty matters into running board and belt.
Treadmill belts shall be cleaned by a damp cloth with soap. And please pay attention to avoid
too wet the electrical components and running belt.
Warning: Make sure power plug disconnect before moving motor cover away, clean the motor
at least once a year.
Running with adjusted alignment and tightness
In order to better use the treadmill and make the treadmill functions work better, it is necessary
for you to adjust the running belt into the best condition.
Running Belt alignment
⚫Put electric treadmill flat on the ground.
⚫Make the electric treadmill run at a speed of about 6-8km/hour.
⚫If the running belt is closer to the right, rotate the right adjusting bolt with 1/2 turn
clockwise, then rotate the left adjusting bolt with 1/2 turn counter-clockwise. (Picture B)
⚫If the running belt is closer to the left, rotate the left adjusting bolt with 1/2 turn clockwise,
then rotate the right adjusting bolt with 1/2 turn counter-clockwise. (Picture A)
Picture A Picture B
Multi-wedge Belt Tension Adjusting
When you use the treadmill for a long time, the multi-wedge belt becomes loose because of the
abrasion, then you have to do some appropriate adjustment to facilitate the safe use.
•Judgment: the feeling of running with the occasional pause phenomenon, which indicating
that the treadmill belt or multi-wedge belt are a little loose and further affirmation need
to be made.

www.powermaxfitness.net
14
•Method of judging which part is loose: Remove the four screws on protective cover, make
the treadmill run at a speed of 1 km/h, and then stand on the running belt, grip the
armrests, and tread the treadmill belt slightly. (we advise treading the treadmill belts with
the user's own weight)
A. The instantaneous step can not stop the belt, the tightness is appropriate.
B. If your instantaneous step stops the running belt, but the multi-wedge belt and former
roller is still running, it indicates that the running belt is loose and appropriate adjustments
must be made to facilitate the safe use.
C. If you observe that the instantaneous step makes the treadmill belt and multi-wedge belt
stop, but the motor is still running, it indicates that the multi-wedge belt is loose and
appropriate adjustments must be made to facilitate the safe use
Step 2: Use a wrench to adjust the screws on the motor base according the condition. Meanwhile,
gently flip the multi-wedge belt between the motor shaft and the front roller, if it is too
loose, you can flip the multi-wedge belt by 100%; if it is too tight, the degree for you to
flip the belt is very limited. It is appropriate to flip the multi-wedge belt by 80% after
adjustment. Please adjust the tightness of the multi-wedge belt into the state that it could
be flipped by 80%.
Step 3: Finally lock the motor base, and install the front cover.
Applying Silicone Oil
Step 1: Lift the running belt slightly.
Step 2: Open the silicone oil bottle, squeeze the silicone oil on the sides of running board, as
shown in the following picture: