Pr lighting Aqua led 1500-w framing User manual

AQUA LED 1500-W FRAMING

PR-8176

This product manual contains important information about the safe installation and use of this projector.

Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

SAFETYAND WARNINGS……………………………………………………………………………………………

INSTRUCTIONS………………………………………………………………………………………………………

APPEARANCE…………………………………………………………………………………………………………

INSTALLATION…………………………………………………………………………………………………………

SETUPAND CONFIGURATION………………………………………………………………………………………

.OPERATION MENU……………………………………………………………………………………………………

DMX PROTOCOL………………………………………………………………………………………………………

LOGOS ON THE SCREEN……………………………………………………………………………………………

ERROR INFORMATION……………………………………………………………………………………………

TECHNICALDATA……………………………………………………………………………………………………

CIRCUIT DIAGRAMAND PCB CONNECTIONS……………………………………………………………………

COMPONENT ORDER CODES………………………………………………………………………………………

The following items are supplied with the projector and please check:

Name

Quantity

Unit

Remark

G clamp

Pcs

XLR connector

Set

Male and female

Safety cord

This manual

Ω clamp

Pcs

Optional

Power Cord

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change

without notice. Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the

course of product improvement.The publishers cannot be held responsible for the accuracy of the information herein, or any

consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are

in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and

do not use the unit.Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

Any future technical changes are not subject to further notice.

Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one year starting from

the delivery date but the light source is not within the warranty.

1. SAFETYAND WARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

the safety information hereinafter!

The following safety signs are used in the user manual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

●When unpacking , check if there is transportation damage before using the projector. Should there be any

damage caused by transportation, consult your dealer and do not use it.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the projector

as he/she likes

●Please be noted that the damage caused by changing the projector at will is not warranted.

●Do not hesitate to contact the dealer or the manufacturer if any questions or advice.

●The projector is for indoor and outdoor use, IP66.

●It can be used in humid and dusty areas.And it can contact water and other non-corrosive liquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

being operated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operation must strictly follow the procedures in the manual

●No repairable parts in the projector and do not open covers for maintenance by yourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Do not connect this device to any type of dimmer pack

●After lamp switched on, the minimum distance between the projector and illuminated surface is 5m

●If there are visible damages on the lamp, lens and protective cover for the screen, i.e., to the extent which affects

its performance like cracking or deformation, please stop using it and contact the manufacture for their

replacement with original parts, otherwise its performance will be compromised

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projector while covers(housing)are off

●Keep the lamp clean and do not touch it with bare hands.

●While operating it, wear protective items.

●Any electrical connection must be carried out by a qualified person .

●Before installation, please confirm the voltage supplied matches what is required for the projector

●Each projector must be properly earthed and installed as per related electrical standards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully or

by pulling the power cable.

●All power cords must conform to related safety and regulations

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened .

●The projector is of class IP66, and not used in the environment higher than it.

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

cord supplied through the safety cord holes for safety support.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

power mains.

●After running for 5minutes, the temperature of the housing of the projector is45℃.After stable operation ,

its temperature is 80℃.

●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not

mean the projector has some defects.

●Don’t touch the covers of the working projector(They are very hot!)

●Do not mount the projector directly on inflammable surface.

●Do not project the beam straightly on combustible items and the minimum distance between the projector

and illuminated items is 5m.

●A projector should be installed with good ventilation and the minimum distance between the projector and

walls is 50cm.At the same time, please ensure the fans and air inlets and outlets are workable.

2. INSTRUCTIONS

●CLEANINGAND MAINTENANCE

If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the

projector has over-temperature protective device. If the temperature is too high, the protective device will be triggered to shut the

projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved,

restart the projector.

The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very necessary to

ensure a reliable use of it. Cooling fans need to be cleaned every 15days. Internal lens, reflector and hot mirror need to be cleaned

periodically to optimize light output.

The cleaning frequency of cooling fans and heat sink is decided by the operations, environment and climate. It is advised to clean

it every 15days or less . Use rubber or bush or other non- metallic tools to carry out cleaning. The tools can’t scratch or deform the

heat sink and fans.

Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning

work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. Keep lens clean

and do not touch optical parts with bare hands.

Special note:

It’s normal phenomena that there will be mild water mist on the lens while the waterproof product is in use.

●Before any maintenance and cleaning, please ensure the project is off the power

●Only qualified person is allowed to do maintenance

●During maintenance and before maintenance, the projector must be off power.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens

whether it runs or not

●Do not use alcohol or other organic solvent to clean the housing to avoid damage.

●Do not use any solvent with chemical elements to clean color filters or hot mirror.

●While a lighting fixture works properly under normal ambient temperature, the maximum temperature

of the external surface of the control device(The integrated control device means the external surface of the

housing of the lighting fixture’s electric chamber)allowed is 75 Celsius degrees.

●For the location of a lighting fixture, itshouldn’t be seen in the distance of less than 4 meters.

●LUBRICATION

To ensure smooth movement of gobos and focus lens, it’s advised rotators’bearings and 2 sliding bars for focus lens be lubricated

every 2 months. High quality and high temperature lubricant/grease is advised..

●TROUBLESHOOTING

PROBLEM

ACTION

The projector can’t be switched on

Check if the fuse is burned

Check if the power cord is connected well

Check if the switching power supply is bad or not connected well. A

professional technician is required for the repair

Check if the control board is connected well. .A professional technician

is required for the repair

The projector can be switched on , but the LED

lamp’s brightness can’t be controlled

Check if the LED driver board is connected well. A professional

technician is required for the repair

The projector can be switched on normally, but

not controlled by the DMX controller

Make sure that the fixture’s start address is right

Replace or repair the XLR signal cable.

The beam is not bright and its brightness

decreases sharply

Make sure the fans are working well or fans and their shields are not blocked

by dust.

Makesure thattheinternaloptics is clean.

Beam appears dim, Low in brightness

Make sure the lamp is within its lifespan

Remove dust or grease from the lenses.

The project image appears to have a halo

Carefully clean the LED lamp, optical lenses and other components.

Heavily Defective Beam

Check if lens are in good condition(not cracked)

Clean dust or grease on the lens.

3. APPEARANCE

4. INSTALLATION

●RIGGING

During transportation, please lock the projector well; Before the use of projector please unlock the head. It’s forbidden to run the

projector without unlock Pan and Tilt.

Head

Arm

Base

Take 2 clamps and 1 safety cords out from the package and mount 2 clamps on the underside of fixture with 4 retainers attached to

each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of

the base as shown above) Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning.

Always ensure that the structure that you are going to mount the projector is secure and is strong enough to support the weight of the

fixture.

WARNING:

●The projector MUST be lifted or carried by the HANDLES instead of clamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

●.For safety, it should not be hung by its sides.

●POWER CONNECTIONS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projector be connected with power separately so that they may be individually switched on and off.

Warning

please run the safety cords through 2 safety

cord holes to ensure safety

Note:

1. the distance between the foot

of the base and the front lens

cover(the head facing downward)

2. the distance between mounting

truss and the front lens

cover( the head facing downward)

3. The maximum diameter of the

rotating head ( minimum spacing

between fixtures)

3PIN

DMX512

PIN FUNCTION

1 GND

2 DATA-

3 DATA+

DMX INDMX OUT

5PIN

DMX512

PIN FUNCTION

1 GND

2 DATA-

3 DATA+

4 N/C

5 N/C

DMX IN

DMX OUT

●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in

accordance with the standards concerned.

●If any questions about the electrical installation, do not continue but consult a qualified electrician.

●The lighting fixture is with waterproof power socket, it should be equipped with same IP rating power

plug.

●DMX CONTROLCONNECTION

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The projector accepts digital control signals in protocol

DMX512 (1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminator as shown in the figure below.

控制器

DMX512

回路插

输入输出输入输出输入

NO.1 NO.2 NO.n

●DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain. The connections are illustrated below

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

DMX TERMINATOR

DMX CONTROLLER

OUTPUT

INPUT

OUTPUT

INPUT

图案片安装滤色片安装

●REPLACEMENT OF GOBOS

Lock tilt and unfasten 4 screws of the small cover of the head. Open the cover and you’ll see the structure as above.

Replacement of the color filter. Pull out the color filter directly by hand as the figure hereinafter in the sequence 1→2. It’s installation

is in reverse sequence as the removal（2→1）.

Rotating gobos. Pull out the rotator as the figure hereinafter and the removal is in the sequence 1→2. Remove spring of the gobo

and take the gobo out. Place a new gobo in the rotator with the spring and ensure the spring is in the narrow groove of the

rotator ,i.e. its inner ring, then flatten it. At last use proper tool to push the tightening plate upward for the spring and use

another hand to help place the rotator in the original place. It is in the reverse sequence of the removal2→1.

Note: Do not touch color filters and glass gobos with bare hands. There should be clean and soft paper or cloth between hand and

glass. Install the chamber cover, tighten 4 inner hexagon screws and unlock Tilt.

DANGER!

BEFORE THE REPLACEMENT OF GOBO, THE PROJECTOR MUST BE OFF POWER.

5. SETUPAND CONFIGURATION

●FRONT PANELOPERATION

Gobo Installation

Fix gobo wheel

Rotating gobo wheel

Color wheel

Projector configuration can be set conveniently via push button and color touch screen.

Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the function menu of

the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the

“OPERATION MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the submenu.

Press button UP or DOWN to change values(plus or minus)

Press button FUNC, it will return to the upper menu. Ifbutton FUNC not pressed, the default will show display status automatically.

●DMX STARTADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The projector has 3 DMX modes. There are short mode ,standard mode and extended mode. For example standard mode

has 38 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 039, No. 3 projector’s address 077, No. 4

projector’s address115, and so on.

Launch the projector. Press button ENTER more than 3seconds to unlock panel.

Press button ENTER to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm; after powered on next time, the default will be last value saved

Press button FUNC, it will return to the upper menu

●DMX WIRELESS CONTROL

The projector has wireless control function with wireless receiver module and antenna for remote control.

The setup of it is below:

1. Enter into the projector’s menu. Select the menu “Config Settigns” via the bottoms of UP and DOWN

2. Select DMX control Mode---- Wireless First (Note: Do not select XLR ONLY). The DMX wireless control

function is activated.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it, Press

“Enter” for the menu of Unlink Wireless under the upper level menu of Config Settigns.

●STAND-ALONE MODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVE MODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

StartAddresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’and Slaves’operation mode can

be set accordingly.

After Powered on, the group will run in Master/Slave Mode

回路插

输入输出输入输出输入

主机从机从机

6. OPERATION MENU

1st LEVEL

2nd LEVEL

3rd LEVEL

4th LEVEL

5th LEVEL

Address

DMX Address

1-478 Short mode

1-475 Standard mode

1-459 Extend mode

IP Address

Default IPAddress

2.X.X.X /10.X.X.X

Custom IPAddress

X.X.X.X

SubNet Mask

X.X.X.X

ArtNet Universe

0-255

sACN Universe

1-63999

Reset

Total Reset

Really Reset?

Confirm/ Cancel

Pan&Tilt Reset

Really Reset?

Confirm/ Cancel

Colour System Reset

Really Reset?

Confirm/ Cancel

Gobo Reset

Really Reset?

Confirm/ Cancel

Zo.Fo.Fr.Pr. Reset

Really Reset?

Confirm/ Cancel

Other Reset

Really Reset?

Confirm/ Cancel

Config Settings

DMX Channel Mode

Short Mode 35CH

Standard Mode 38CH

Extended Mode 54CH

View Selected Mode

Strobe

…..

Signal Select

XLR Only

XLR First

Wireless Only

Wireless First

Wireless In/XLR Out

Artnet Only

Artnet In/XLR Out

sACN Only

sACN In /XLR Out

Loss of DMX

Normal time out

Hold Last Value

Display Config

Display Mode

OffAfter Delay

OnAlways

Display Invert

Invert OFF

Invert ON

InvertAuto

Language Setting

English

DMX TERMINATOR

MASTER

SLAVE

INPUT

OUTPUT

INPUT

Chinese

Temperature Unit

Celsius Degree

Fahrenheit Degree

Un-LinkWireless

Really Un-Link?

Confirm/ Cancel

Factory Defaults

Restore Defaults?

Confirm/ Cancel

Option Settings

Pan/Tilt Settings

Pan DMX Invert

OFF/ ON

Tilt DMX Invert

OFF/ ON

Pan Tilt Swap

OFF/ ON

XYFeedback

OFF/ ON

Pan/Tilt mode

Speed/Time

Invert Settings

Iris Invert

OFF/ ON

Zoom Invert

OFF/ ON

CYM Invert

OFF/ ON

CTO Invert

OFF/ ON

Dimmer Settings

Gamma Curve

Gamma 2.0/2.2/2.4/2.6

LED Refresh Rate

1200/2400/4800/10000/1200

0/15000/20000/25000Hz

Dimmer Speed

Fast/Medium/Slow Speed

Fan Settings

Standard/Theatre

Defaults

Restore Defaults?

Confirm/Cancle

Information

View DMX Values

Lamp Hours

Reset Lamp Hours

Total Hours

Temperature

Display Board XX℃/F

Pan Board XX℃/F

Driver Board 1 XX℃/F

Driver Board 2 XX℃/F

Driver Board 3 XX℃/F

Driver Board 4 XX℃/F

Blade Board XX℃/F

Fan Board XX℃/F

Tilt Board XX℃/F

LED Sensor XX℃/F

SoftwareVersion

Display Board

Sys= XXX

Boot =XXX

Pan Board

Sys= XXX

Boot =XXX

Driver Board 1

Sys= XXX

Boot =XXX

Driver Board 2

Sys= XXX

Boot =XXX

Driver Board 3

Sys= XXX

Boot =XXX

Driver Board 4

Sys= XXX

Boot =XXX

Blade Board

Sys= XXX

Boot =XXX

Fan Board

Sys= XXX

Boot =XXX

Tilt Board

Sys= XXX

Boot =XXX

Electronic SN

Electronic SN=

************

RDM Device Label

AQUA LED 1500-W

FRAMING

ANSI E1.20 RDM

Fan Status

Head Fan

Service

Manual Effect Control

Strobe XXX

Dimmer XXX

…

FactoryTest

Operation

Mode

DMX Mode

Change Operation Mode?

Confirm/ Cancel

Master Mode

Preset Memory

Change Operation Mode?

Confirm/ Cancel

User Memory 1

Change Operation Mode?

User Memory 2

Change Operation Mode?

Stand-Alone Mode

Preset Memory

Change Operation Mode?

User Memory 1

Change Operation Mode?

User Memory 2

Change Operation Mode?

Static Scene

Change Operation Mode?

User

Memories

Edit User Memory

Edit User Memory 1

Edit User Memory 2

Scene XX

（1~200 Scenes）

Strobe XXX

Dimmer XXX

…

Delay Time XXX

Delay Unit

Link To Step XXX

Edit Static Scene

Strobe XXX

Dimmer XXX

…

Init User Memory

Reset User Memory 1

Reset User Memory?

Input Password 123

Reset User Memory 2

Reset User Memory?

Input Password 123

Reset Static Scene

Reset Static Scene?

Input Password 123

7.DMX PROTOCOL

Short

mode

Standard

mode

Extended

mode

Function Description

Decimal Low

Decimal High

Strobe

Pulse strobe speed from slow to fast

127

Strobe speed slow to fast

128

255

Dimmer

Dimmer from dark to light (0-100%)

255

Dimmer Fine

Fine dimmer

255

CYM Macro

The following functions can be used after CMY,CTO, and Color Wheels1

and Color Wheel2

No Function

Colour Macro 1

Colour Macro 2

Colour Macro 3

Colour Macro 4

Colour Macro 5

Colour Macro 6

Colour Macro 7

Colour Macro 8

Colour Macro 9

Colour Macro 10

Colour Macro 11

Colour Macro 12

Colour Macro 13

Colour Macro 14

Colour Macro 15

Colour Macro 16

Colour Macro 17

Colour Macro 18

Colour Macro 19

Colour Macro 20

Colour Macro 21

Colour Macro 22

Colour Macro 23

Colour Macro 24

Colour Macro 25

Colour Macro 26

Colour Macro 27

Colour Macro 28

Colour Macro 29

Colour Macro 30

Colour Macro 31

Colour Macro 32

Colour Macro 33

Colour Macro 34

Colour Macro 35

Colour Macro 36

Colour Macro 37

Colour Macro 38

Colour Macro 39

Colour Macro 40

Colour Macro 41

Colour Macro 42

Colour Macro 43

Colour Macro 44

Colour Macro 45

Colour Macro 46

Colour Macro 47

100

101

Colour Macro 48

102

103

Colour Macro 49

104

105

Colour Macro 50

106

107

Colour Macro 51

108

109

Colour Macro 52

110

111

Colour Macro 53

112

113

Colour Macro 54

114

115

Colour Macro 55

116

117

Colour Macro 56

118

119

Colour Macro 57

120

121

Colour Macro 58

122

123

Colour Macro 59

124

125

Colour Macro 60

126

127

Colour Macro 61

128

129

Colour Macro 62

130

131

Colour Macro 63

132

133

Colour Macro 64

134

135

Colour Macro 65

136

137

Colour Macro 66

138

139

Colour Macro 67

140

141

Colour Macro 68

142

143

Colour Macro 69

144

145

Colour Macro 70

146

147

Colour Macro 71

148

149

Colour Macro 72

150

151

Colour Macro 73

152

153

Colour Macro 74

154

155

Colour Macro 75

156

157

Colour Macro 76

158

159

Colour Macro 77

160

161

Colour Macro 78

162

163

Colour Macro 79

164

165

Colour Macro 80

166

167

Colour Macro 81

168

169

Colour Macro82

170

171

Colour Macro 83

172

173

Colour Macro 84

174

175

Colour Macro 85

176

177

Colour Macro 86

178

179

Colour Macro 87

180

181

Colour Macro 88

182

183

Colour Macro 89

184

185

Colour Macro 90

186

187

Colour Macro 91

188

189

Colour Macro 92

190

191

Colour Macro 93

192

193

Colour Macro 94

194

195

Colour Macro 95

196

197

Colour Macro 96

198

199

CMY colour mixing from slow to fast

200

255

Cyan

Cyan (Linear 0-100%)

255

Cyan Fine

Cyan in 16 Bit precision

255

Yellow

Yellow (Linear 0-100%)

255

Yellow Fine

Yellow in 16 Bit precision

255

Magenta

Magenta (Linear 0-100%)

255

Magenta Fine

Magenta in 16 Bit precision

255

CTO

Linear adjust from high to low

255

CTO Fine

CTO in 16 Bit precision

255

Colour Wheel

Continual positioning

index 0-360°

positioning

White

White/color1(Blue)

Color1(Blue)

Color1(Blue)/colour 2(Green)

Colour2(Grenn)

Colour 2(Green)/colour 3(Orange)

Colour3(Orange)

Colour 3(Orange) /colour 4 (Magenta)

Colour4 (Magenta)

Colour 4 (Magenta)/colour 5(Red)

100

103

Colour 5(Red)

104

107

Colour 5(Red)/colour 6 (Purple)

108

111

Colour 6 (Purple)

112

115

Colour 6 (Purple) White

116

119

White

120

127

Clockwise rainbow effect rotation speed from slow to fast

128

191

Anti-clockwise rainbow effect rotation speed from slow to fast

192

255

Colour Wheel Fine

Colour Continual positioning in 16 Bit precision

255

Iris

Linear Iris from small to big 0-100%

255

Iris in 16 bit

Iris in 16 bit precision

255

Iris Macro

Iris Macro disabled

Iris Macro1: from big tosmall with speed from slow to fast

Iris Macro2: from small to big with speed from slow to fast

138

Iris Macro3: Iris contracts from slow to fast

139

202

Iris Macro4(Macro1 at random) with speed from slow to fast

203

210

Iris Macro5(Macro2 at random) with speed from slow to fast

211

218

Iris Macro6(Macro3 at random) with speed from slow to fast

219

226

Open

227

255

Fixed gobo wheel

White

Gobo1

Gobo2

Gobo3

Gobo4

Gobo5

Gobo6

111

Gobo7

112

127

Clockwise rotation from slow to fast

128

149

Anti-clockwise rotation from slow to fast

150

171

Gobo1 shake from slow to fast

172

183

Gobo2 shake from slow to fast

184

195

Gobo3 shake from slow to fast

196

207

Gobo4 shake from slow to fast

208

219

Gobo5 shake from slow to fast

220

231

Gobo6 shake from slow to fast

232

243

Gobo7 shake from slow to fast

244

255

Rotating gobo wheel

White

Gobo1

Gobo2

Gobo3

Gobo4

Gobo5

111

Gobo6

112

127

Clockwise rotation from slow to fast

128

143

Anti-clockwise rotation from slow to fast

144

159

Gobo1 shake from slow to fast

160

175

Gobo2 shake from slow to fast

176

191

Gobo3 shake from slow to fast

192

207

Gobo4 shake from slow to fast

208

223

Gobo5 shake from slow to fast

224

239

Gobo6 shake from slow to fast

240

255

Rotating gobo wheel rotation

Indexing 0-360°

128

Clockwise rotation from slow to fast

129

188

Stop

189

195

Anti-clockwise rotation from slow to fast

196

255

Rotating gobo wheel rotation in 16 bit

Rotating gobo wheel fine rotation

255

Framing blade 1 left

Framing blade 1 left linearly closing from big to small

255

Framing blade 1 left in 16 bit

Framing blade 1 left fine adjustment

255

Framing blade 1 right

Framing blade 1 right linearly closing from big to small

255

Framing blade 1 right in 16 bit

Framing blade 1 right fine adjustment

255

Framing blade 2 left

Framing blade2 left linearly closing from big to small

255

Framing blade 2 left in 16 bit

Framing blade 2 left fine adjustment

255

Framing blade 2 right

Framing blade 2 right linearly closing from big to small

255

Framing blade 2 right in 16 bit

Framing blade 2 right fine adjustment

255

Framing blade 3 left

Framing blade 3left linearly closing from big to small

255

Framing blade 3 left in 16 bit

Framing blade 3 left fine adjustment

255

Framing blade 3 right

Framing blade 3 right linearly closing from big to small

255

Framing blade 3right in 16 bit

Framing blade 3right fine adjustment

255

Framing blade 4 left

Framing blade 4left linearly closing from big to small

255

Framing blade 4left in 16 bit

Framing blade 4 left fine adjustment

255

Framing blade 4 right

Framing blade 4 right linearly closing from big to small

255

Framing blade 4right in 16 bit

Framing blade 4right fine adjustment

255

Framing module rotation

Framing module indexing(0-360degrees)

127

Stop

128

Framing module clockwise rotation from slow to fast

129

188

Stop

189

195

Framing module anti-clockwise rotation from slow to fast

196

255

Framing module rotation in 16 bit

Framing module fine rotation

255

Prism

No Prism

Prism

255

Prism rotation

Prism index

127

Prism stops

128

Rotation speed from slow to fast

129

191

Stop rotating

192

Reverse rotation speed from slow to fast

193

255

Effect Wheel

No effect wheel

Effect wheel in

255

Effect Wheel Rotation

Forwards rotation from slow to fast

127

Reverse rotation from slow to fast

128

255

Frost

Light Frost from 0% to 100%

255

Focus

Linearly focusing

255

Focus Fine

Focus in 16 precision

255

Zoom

Linearly zooming

255

Zoom Fine

Zoom in 16 Bit precision

255

Pan

Pan movement

255

Pan Fine

Pan movement in 16 bit precision

255

Tilt

Tilt movement

255

Tilt fine

Tilt movement 16 bit precision

255

Pan/Tilt speed

Fast Speed Mode

Pan &Tilt speed from fast to slow

255

Power/Special functions

No function:

Reserved

To activate following functions, stay in DMX value for at least 5 s

Graphic display On

Graphic display Off

Reserved

Fan standard mode

Fan theater mode

Reserved

Fast speed dimmer

Mid speed dimmer

Slow speed dimmer

Gamma curve 2.0

Gamma curve 2.2

Gamma curve 2.4

Gamma curve 2.6

LED refresh rate 1200Hz

LED refresh rate 2400Hz

LED refresh rate 4800Hz

LED refresh rate 10000Hz

LED refresh rate 12000Hz

LED refresh rate 1500Hz

LED refresh rate 20000Hz

LED refresh rate 25000Hz

Reserved

Pan/Tilt speed mode

Pan/Tilt time mode

Reserved

100

129

Reserved

130

139

Pan/Tilt reset

140

149

Colour system reset

150

159

Gobo wheels reset

160

169

Reserved

170

179

Zoom/focus/frost/prism reset

180

189

Others(Iris/ effect wheel/Framing module) reset

190

199

Total reset

200

209

Reserved

210

229

Reserved

240

255

Note:

1. Fan error can automatically turn the LED lamp off.

2. Note: "Speed Mode" means Pan and Tilt will move from Point A to Point B at their respective maximum speeds."Time Mode"

means both Pan and Tilt will arrive at designated point at the same time. It's advised Time Mode be used if the projector runs circles or

in oblique lines.

8. LOGOS ON THE TOUCH SCREEN

Config Settings

Option Settings

Information

Error Messages

Service

Address

Operation Mode

Reset

User Memories

9. ERROR INFORMATION

The system can detect some errors during the reset, if displayed, touch the logo to view the error.

The error messages are as follows:

Name

Type

Correction

Pan

Timeout/magnet Sensor/Encoder