Precision Rated Optics VIP-35 User manual

VIP-35 Manual
Video Inspection Probe

Tel: [phone] • Fax: [phone] • Email: [e-mail]
www.PrecisionRatedOptics.com
2
Foreword
Thank you for purchasing our products. Before assembly and use, make certain that all of the parts you
have ordered are present. Check the packaging carefully as some parts are small and can be overlooked.
Also, locate any additional parts and accessories you may have purchased.
Safety Conventions
You should understand the following conventions before using the product described in this manual.
CAUTION
Refers to a potential product hazard, it requires a procedure which, if not correctly followed,
may result in component damage. Do not proceed unless you understand and meet the required
conditions.
Introduction
Hand-held Probe Introduction
The VIP-35 is a portable, video microscope used to inspect fiber optic terminations. More specifically, it
is used to inspect hard-to-reach connectors that are installed on the “backside” of patch panels or inside
hardware devices. It eliminates the need to access the backside of patch panels or disassemble hardware
devices prior to inspection.
Many patch panels are designed to allow the front connector to be easily inspected, but the back one is
often difficult to access. Inspecting the connector on the front side of the panel can usually be performed
with a simple fiber inspection microscope. However, the back connectors are not as easily inspected with
traditional microscopes, thus requiring time-consuming troubleshooting. The product offers a fast and
effective means of installing, troubleshooting or maintaining fiber optic patch panels.
Inspection of Cable Assemblies
When Video Inspection Probe is equipped with proper Adapter Tip, you can also inspect patch cords,
pigtails, and cable assemblies
Information contained in this manual is believed to be accurate and reliable. However, no responsibility is assumed by
Precision Rate Optics for its use nor for any infringements of patents or other rights of third parties that may result
from its use. No license is granted by implication or otherwise under any patent rights of Precision Rated Optics.
The information contained in the publications is subject to change without notice.

Tel: [phone] • Fax: [phone] • Email: [e-mail]
www.PrecisionRatedOptics.com 3
Structure/Parts
A. Analog Probe
This probe utilizes an analog CCD, which outputs an NTSC or a PAL signal. The signal is routed through
a 4-pin connector that routes power into the probe, and the video signal out of the probe. This unit is
suitable for use with our hand held LCD display.
a 1. Barrel Assembly
The barrel assembly houses the optics which accommodates different adapters, such as FC, SC, ST, LC,
E2000, MTRJ and other customized PC or APC adapters.
a 2. Focus Control
When the figure shows on monitor, screw the focus control to make it clearest.
B. Structure / Parts
Top View
4-pin
Connector
Power
Connector
USB Port
SD Card Slot
Brightness
Control

Tel: [phone] • Fax: [phone] • Email: [e-mail]
www.PrecisionRatedOptics.com
4
These monitors can be powered by an output 110-240V DC/AC or a rechargeable Li-ion battery equipped
inside. Video input is dedicated to PAL/NTSC formatted probe. All of the display’s controls are built into
the handle for easy access.
b 1. Photo Snapping
When the ‘Power Switch’ is turned on, pressing ‘Camera’ will allow you to take a photo for the inspection.
b 2. Data Outputting
If you need to check the data sved in the SD card, you can either connect the monitor via USB cable to
your computer, or take the SD card out of the slot and read it with a card reader.
C. Standard Tips
3.5 Inch LCD Monitor
Camera
Camera
Reserved Button
Power Switch
Reserved Button

Tel: [phone] • Fax: [phone] • Email: [e-mail]
www.PrecisionRatedOptics.com 5
Installation
Tip Assembly
Installing Tips on Probe
Assembly & Tip Installed Standard
Step 1
Locate tip you want to install and look at the threaded end. This screw acts as a “key” and is already
mounded with the Key Channel. DO NOT try to screw the Key Channel off from the threaded Key,
which might destroy the whole probe.
Step 2
Slightly screw the Key that you need onto the Key Channel.
LCD Monitor Assembly & Controls
Using the LCD Display with the Probe Connect the Probe to the Display
Step 1
Connect the cable from the probe to the monitor using the 4-pin connector on the
bottom of the monitor.
Step 2
Connect the AC power adapter/charger if necessary.
On/Off Control
(Toggle switch) Press upward to turn the unit on, press downward to shut the unit off.
AC Power
Using the DC/AC power adapter has the following advantages: Use external power (DC/AC power adapter/
charger) to power the LCD directly from a DC/AC power source, or charge the battery pack. Both can be
accomplished simultaneously.

Tel: [phone] • Fax: [phone] • Email: [e-mail]
www.PrecisionRatedOptics.com
6
Adapter Type Description
VIP-A-25 (2.5mm UPC Male) FC/SC/ST/E2000 patch cord UPC termination
VIP-A-125 (1.25mm UPC Male) LC/MU patch cord UPC termination
VIP-A-25/APC (2.5mm APC Male) FC/SC/ST/E2000 patch cord APC termination
VIP-A-125/APC (1.25mm APC Male) LC/MU patch cord APC termination
VIP-AB-25 (2.5mm UPC) Female) FC/SC/ST/E2000 UPC bulkhead
VIP-AB-125 (LC UPC Female) LC UPC bulkhead
VIP-AB-SC/APC (SC APC Female) SC APC bulkhead
VIP-AB-FC/APC (FC APC Female) FC APC bulkhead
VIP-AB-LC/APC (LC APC Female) LC APC bulkhead
SPECIFICATIONS
Item / Model No. VIP-35 Kit VIP-35 w/Data
Magnification 400X
Display Size 3.5”
Dimensions (HxWxD) 6.69” x 3.94” x 1.77”
Weight 14.1 oz
Display Type TFT Active Matrix
Video Output PAL / NTSC
Power 12V DC Built-in Li-ion Rechargeable Battery
Input Power 110-240VAC Adapter
Power Supply AC or DC Operation
Battery 3 Hours
Charging 3 Hours
Operating Temperature 4ºF ~ 122ºF (-10ºC ~ 50ºC)
Connectors 1.25mm, 2.5mm Patchcord Tips
Data Storage No Yes
Data Download No Yes
Warranty Standard 1-Year Manufacturer Warranty
(Extended Warranty Available)
VIP-35 Kit Standard Package Includes:
VIP-35, 400X Inspection Probe and Monitor, AC/DC Charger, FC/SC Bulkhead Adapter, LC
Bulkhead Adapter, 2.5mm Universal Adapter, 1.25mm Universal Adapter, Soft Carrying Case
VIP-35 w/Data Storage Kit Standard Package Includes:
VIP-35, 400X Inspection Probe and Monitor, AC/DC Charger, FC/SC Bulkhead Adapter, LC Bulkhead
Adapter, 2.5mm Universal Adapter, 1.25mm Universal Adapter, USB Data Cable, Soft Carrying Case

Tel: [phone] • Fax: [phone] • Email: [e-mail]
www.PrecisionRatedOptics.com 7
Warranty
We warrant this equipment against defects in material and workmanship for a period of one year from
the date of original shipment. We also warrant that this equipment will meet applicable specifications
under normal use. During the warranty period, we will, at our sole discretion, repair or replace for any
defective product free of charge should the equipment need to be repaired.
IMPORTANT
The warranty will become null and void if
●the equipment has been tampered with, repaired, or worked upon by unauthorized individuals.
●the warranty label has been removed.
●product enclosure screws, other than those specified in this manual, have been removed.
●the product enclosure has been opened, other than as explained in this manual.
●the equipment serial number has been altered, erased, or removed.
●the equipment has been misused, neglected, or damaged by accident.
P/N: PRO-VIP-35-M v.1.29.18

Precision Rated Optics, Inc.
National Sales Office
2030 Blue Heron Circle
Birmingham, AL 35242
Precision Rated Optics, Inc.
Corporate Office
Billing & Processing
PO Box 877 Trexlertown, PA 18087
Precision Rated Optics, Inc.
Product Distribution Center
Manufacturing & Testing
9999 Hamilton Blvd
Breinigsville, PA 18031