Precor SPINNER RALLY User manual

To assemble the Spinner®Rally and Spinner®Shift, follow the steps in the order listed
in this assembly guide. For more product information, visit us at www.precor.com.
WARNING At least two people are required to assemble the equipment.
DO NOT attempt assembly by yourself.
Assembly Requirements
When assembling the bike, we recommend you:
• Assemble the equipment close to where you plan to use it.
• Assemble the equipment on a solid, flat surface, so that it remains level
and stable.
• Leave a minimum of 0.5 m (19.7 in.) on at least once side of the bike
and 0.5 m (19.7 in.) behind or in front of the bike.
Spinner® Rally and Spinner® Shift
Assembly Guide
Hardware Kit
Begin Assembly
Remove the following parts from the packaging: handlebar assembly, handlebar post, hardware kit,
product documentation, seat assembly, seat post, and spare parts.
CAUTION Damage to the bike during assembly is not covered by the Precor Limited
Warranty.
During assembly, you must protect the handlebar and seat adjustment pop-pin
threaded stems from damage.
To attach the rear stabilizer:
1. Stand the bike frame on its front end (toward flywheel) and place a piece of foam under the bike
frame (Figure 1) to protect the handlebar adjustment pop-pin stem from damage.
2. Remove the packaging from the rear stabilizer and gently pry o the plastic protection plate from
the frame. Be careful not to chip the paint.
3. Slide the rear stabilizer attachment bar into the slot in the bike frame (Figure 2).
4. Attach the rear stabilizer to the frame using two bolts and two flat washers (Figure 3).
Using a hex key , tighten to 15.6 ft-lb (21.2 N-m).
To attach the front stabilizer:
1. Stand the bike frame on its back end and place a piece of foam under the bike frame (Figure 4) to
protect the seat adjustment pop-pin stem from damage.
2. Remove the packaging from the front stabilizer and gently pry o the plastic protection plate from
the frame. Be careful not to chip the paint.
3. Slide the front stabilizer attachment bar into the slot in the bike frame (Figure 2).
4. Attach the front stabilizer to the frame using two bolts and two flat washers (Figure 5).
Using a hex key , tighten to 15.6 ft-lb (21.2 N-m).
5. Return the bike to the upright position.
Figure 2
Figure 3
Figure 4 Figure 5
Seat assembly
Handlebar
assembly
Rear
stabilizer
Bike frame
Seat post
Handlebar post
Front
stabilizer
Pedal
Seat adjustment
pop-pin
Handlebar
adjustment
pop-pin
Seat
slider knob
Fore/a ft handlebar
knob
Resistance
knob
Flywheel
Adjustment feet
Crank arm
Component Quantity
Socket head bolt (M8 x 30 mm) 4
Flat washer (8 mm) 4
Socket head bolt (M3 x 8 mm) 7
Socket head bolt (M8 x 16 mm) 2
Hex key (6 mm) 1
Hex key (8 mm) 1
Component Quantity
Hex key (2.5 mm) 1
Seat slider end cap 1
Handlebar post end cap 1
Stabilizer attachment bar 2
Figure 1

Spinner® Rally and Spinner® Shift Assembly Guide | P/N 305002-103 rev C, ENU
©2016 Precor Incorporated | January 2016
Level the Bike
Important Place the equipment on a flat surface. Rotating the adjustable feet does not compensate for extremely uneven surfaces.
Make sure the bike is level before allowing anyone to use it.
To level the bike:
1. Try to rock the bike. If there is any movement, tip the bike to one side to locate the adjustable feet (Figure 14).
2. Correct the height of each adjustable foot by turning it clockwise (+) to lower the bike, or counterclockwise (-) to raise the bike.
3. When you are finished leveling the bike, place it on the floor. Recheck for movement and readjust as necessary.
Attach the Pedals
Hold the pedals with the toe straps facing forward.
To attach the pedals:
1. Insert a pedal into its corresponding crank arm (Figure 12).
2. Use a rubber mallet to lightly tap the center of the pedal into the crank arm to seat it (Figure 12).
3. Secure the pedal using one bolt (Figure 13) and torque to 33 ft-lb (45 N-m) with the hex key .
4. Repeat Steps 1-3 to attach the other pedal.
Figure 12 Figure 13
To attach the seat assembly:
1. Slide the seat assembly onto the seat post (Figure 6).
2. Insert one bolt into the underside of the seat slider and fully tighten it to set the travel limit (Figure 7).
3. Attach the seat slider end cap using three bolts (Figure 8) and fully tighten with the hex key .
Figure 9
Figure 7 Figure 8
Figure 14
Bike Assembly Checklist
Use this checklist to make sure your bike is assembled properly.
 Check that all bolts are tightened to proper torque specification and no parts are missing.
 Check that the handlebar and seat posts move freely and lock in dierent positions.
 Check that the seat is level and does not rotate or tilt. Tighten and adjust as needed.
 Test the seat for movement front to rear.
 Brake tension is adjustable by turning the resistance knob in the front of the seat. Pressing down on the knob will apply the brake if you need to
stop quickly.
 Pedal the bike at a moderate pace and test the resistance knob for smooth resistance changes.
 Press down on the knob to ensure the bike stops quickly.
Once testing is complete, tip the bike forward using the handlebars and roll it on a smooth surface to its final use location. Turn the adjustable feet to level
the bike.
Figure 6
To attach the handlebar assembly:
1. Slide the handlebar assembly onto the handlebar post (Figure 9) by loosening the fore/aft handlebar knob and pulling it up to align with the grooves
on the handlebar post.
2. Insert one bolt into the post and fully tighten it to set the travel limit (Figure 10).
3. Attach the handlebar post end cap using two bolts (Figure 11) and fully tighten with the hex key .
Figure 11Figure 10