Precor QUEENAX PF175 2D User manual

Installation Assembly Guide
QUEENAX™ PF175 2D
WALL SOLUTION

Contents
Introduction 1
Additional Documentation 2
Contact Information 2
General Information 3
Tools 3
Safety Equipment 4
Orientation Convention 4
Equipment Part and Option Identification 5
Torque Specifications 6
Cleaning 7
Getting Started 8
Baseline installation procedure 8
Installation and assembly requirements 8
Receiving Parts 8
Assembly and Installation Tips 9
Unpacking boxes 9
Fastener Tips 9
Assembly and Installation 10
Introduction 10
Procedure 10
Prepare Towers for installation 10
Anchor the towers to the floor 12
Install the Tower Placards 15
Install the Wall Bars 15
Anchor the Floor Fixings to the floor 17
Install remaining panels 20
Install the Unit Optionals 20
Install Placards, Labels, and Decals 21
Horizontal VIPR & Roller Shelf Optional Assembly 22
ii

23
Horizontal Bag Shelf Optional Assembly 23
Universal Rack Element 25
Floor Anchoring Requirements 27
Floor material requirements 27
Anchor bolt requirements 27
Torque specification 27
Approved anchor bolt types 27
Anchor bolt installation Summary 28
Appendix A : Edition Information i
Edition i
Copyright i
Trademarks i
Safety Instruction i
Safety Notices i
iii

Introduction
This document contains information required to install and assembly the Queenax PF175 2D Wall
Solution storage unit. Follow the assembly instructions in the order given to correctly and efficiently
assemble and install the unit.
If you are not a Precor Queenax certified servicer, you must not attempt to install and assemble this
Precor product. Call your dealer for information.
WARNING:Only Precor Queenax certified service providers and technicians are author-
ized to assemble and install this product. Many parts are large and heavy requiring mul-
tiple technicians and specialized lift equipment to assembly. Personal injury or equipment
damage can occur during installation and during use if improperly assembled and
installed.
1
1 Introduction

Additional Documentation
You can also view the install assembly guide online at : Online Service Manual
Contact Information
Contact Precor Queenax installation coordinator or e-mail at [e-mail] with any
issues prior to or during installation.
See Also
"General Information" on page3
"Getting Started" on page8
"Assembly and Installation" on page10
"Floor Anchoring Requirements" on page27
2
1 Introduction

General Information
This section provides general information that will help you to use this guide to assemble and install
the PF175 2D Wall Solution storage unit including the required tools, specifications, parts iden-
tification, unit orientation, cleaning, etc.
Tools
The following tools are required to assemble Queenax products:
Note:One set of power tools per installer is recommended.
The following tools are required to assemble Queenax products:
l½” Drive hammer drill or Concrete drill
omasonry bits appropriately sized for anchor types (refer to mfg's guidelines for select-
ing anchor bolt bit sizes.)
o3 mm, 6 mm, 10.5 mm, and 12.5 mm metal cutting bits
l½” Drive Battery Impact Driver
lBattery Angle Grinder
oCutting disc and abrasive disc (grit #40)
lOscillating Tool (for cutting flooring)
oWood and scraper blades
lMetric tape measure
lLaser measure
lUtility Knife
lTap driver (10 mm & 12 mm cutting threads
lRubber mallet
lHammer
lLadders
lMetric combination wrenches (13 mm, 17 mm, comm, and 22 mm)
l½” and 3/8” drive ratchets
lTorque1wrench 100 ft-lbs (136 N•m
lMetric hex key set
l½” metric hex key sockets from (6 mm – 10 mm, 13 mm, 17 mm, comm, and 22 mm)
1Torque is a measure of the force that can cause an object to rotate about an axis. Bolt/nut
example: 5 nM torque is equivalent to 5 newtons of force applied one meter from the center of the
bolt, 6 ft-lb is equivalent to 6 lb of force applied 1 foot away from the center of the bolt.
3
2 General Information
Tools

o1 short set and 1 long set with ball end
l3/8” metric hex sockets (13 mm, 17 mm, and comm
l½” universal joint
l½” to 3/8” socket adapter
l½” short and long extensions
lVacuum cleaner
Note:One set of power tools per installer is recommended.
Safety Equipment
The following safety equipment is recommended:
lSafety vest
lGloves
lRespirator
lHard hat
lEarplugs
lSafety glasses
lSafety toe work boots
Orientation Convention
The equipment front, right, left, and back orientation.
4
2 General Information
Safety Equipment

Equipment Part and Option Identification
5
2 General Information
Equipment Part and Option Identification

(missing or bad snippet)
Torque Specifications
This table provides a summary of system component specifications.
System Component Specification
M10 Bolt torque [[[Undefined variable Specifications.QNX-
M10Bolt]]]
M12 bolt torque [[[Undefined variable Specifications.QNX-
M12Bolt]]]
M14 bolt torque [[[Undefined variable Specifications.QNX-
M14Bolts]]]
6
2 General Information
Torque Specifications

System Component Specification
Anchor bolt torque1[[[Undefined variable Specifications.QNX-
AnchorBolt]]]
Note: 1) see "Floor Anchoring Requirements" on page1
Cleaning
1. Wipe down equipment with recommended cleaning solution.
lGeneral: 1 oz. mild soap to 30 oz. water. .
(missing or bad snippet)
2. Rinse using a clean lint-free cloth and dampened with water only. Dry completely with
another clean lint-free cloth.
See Also
"Introduction" on page1
"Getting Started" on page8
"Assembly and Installation" on page10
"Floor Anchoring Requirements" on page27
7
2 General Information
Cleaning