Prem-I-Air EH1710 User manual

1
2580 Ver. 3 –0918
EH1710 / EH1710BLK
2kW Convector Heater
This product is only suitable for well-insulated
spaces or occasional use.

2
2580 Ver. 3 –0918

3
2580 Ver. 3 –0918
IMPORTANT
Installer and Users please note:
These instructions should be read carefully and left with the user of the product for
future reference. BEFORE USE
You must inspect the appliance including its cable and plug for any signs of
damage. If the product is damaged, DO NOT use it, and contact your supplier
immediately. PRODUCT SAFETY
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
Do not leave this product unattended when in use.
Do not use the heater unless the feet are correctly attached.
Children shall not play with the appliance.
We advise not to use this heater on carpets which have a thick pile.
Please ensure the heater is placed on a firm and level surface.
Cleaning and user maintenance shall not be made by children without
supervision.
Do not cover. This symbol shown on the casing of the heater means
that the heater should not be covered.
For indoor use only.
Do not use in bathrooms,
Do not use in wet or damp locations.
Do not place the mains lead beneath a carpet or rug.
Do not position heater immediately below a socket outlet.
Before using please ensure the intended socket / electrical outlet matches the
recommended rating issued to the heater.
Do not use the heater in locations where paint, petrol or other flammable liquids
are used or stored.
Please ensure heater is switched off and unplug when not in use, also keep
unplug before assembly or disassembling parts.
Please avoid the use of an extension lead with this heater as this could cause
the product to overheat.
Do not use the heater for other than its intended use.
Do no insert any object into the heater through the grilles. This may damage
the heater or result in overheating or electric shock.

4
2580 Ver. 3 –0918
ASSEMBLY / INSTALLATION
For free-standing use: attach the feet to the underneath of the heater
using the four 10 mm screws. The feet are placed at the end of the case.
OPERATION
1. Power 750W
2. Power 1250W
1&2. Power 2000W
3. Thermostat
Note: When heaters are turned on for the first time or when they are turned on after
not being used for long period in time it is normal for that the heater may emit some
smell and fumes. This will disappear when the heater has been on for a short while,
if the smell or fumes do notdisappear we advise toswitch off the heater and contact
a specialist.
Following the above guidelines choose a suitable location for the heater.
Turn the thermostat dial fully in a clockwise direction to the maximum
setting.
2
1
3

5
2580 Ver. 3 –0918
Turn on the heater by the power switches on the side of the heater, once
on these will illuminate. For the maximum heat setting both switches
should be on.
To reach the desired room temperature turn the thermostat anti-clockwise
until the thermostat “clicks off” and the lights on the switches are seen to
go out. The heater will keep the air temperature in the room at the set
temperature by switching on & off automatically.
NOTE: The heater does remain hot / warm for some time after the unit has
been switch off, please handle with care.
PAT TESTING
When used in a workplace, this product should be safety-tested yearly by a
qualified electrician (PAT Tested). We recommend that it is PAT tested regularly
when used in a domestic environment.
GENERAL SAFETY REQUIREMENTS
Domestic wiring must be tested periodically by a qualified electrician at least once
every 10 years or at every change of occupancy.
For office and retail premises, and buildings such as village halls, the wiring must
be inspected at least once every 5 years.
It is recommended that all buildings be fitted with smoke alarms (it is mandatory for
new buildings).
OPERATING COSTS
At time of going to press, the average cost of electricity is £0.145 per unit (kilowatt-
hour). The amount you are being charged will be shown on your electricity bill.
At this cost, the EH1710 / EH1710BLK will cost £0.29 per hour to run with the
thermostat set to its maximum.
If the thermostat is used to regulate the temperature, the operating costs will be
lower, depending on the room temperature.

6
2580 Ver. 3 –0918
MAINTENANCE
Before cleaning, turn the heater off, and disconnect from the mains supply. The
heater may then be cleaned using a damp cloth with a drop of washing-up liquid to
remove any dust or dirt from the case. Do no use stronger detergents or solvents
as these may damage the plastic.
Using a dry 1" (25 mm) paint-brush, remove any dust from the grilles.
If the mains lead is damaged, it must be replaced by the manufacturer or and
authorised service centre. If the mains plug needs to be replaced, proceed
as follows:
Connect the brown wire to the terminal
labelled "L".
Connect the blue wire to the terminal
labelled "N".
Make sure that the cord-grip is
positioned correctly (over the outer sheath of the
cable) and it fully tightened.
DISPOSAL AND RECYCLING
You must not dispose of this appliance with domestic household waste.
Most local authorities have specific collection system for appliances and disposal
is free of charge to the end-user.
When replacing an existing appliance with a similar newappliance your retailer may
take the old appliance for disposal.
TECHNICAL SPECIFICATION
Dimensions (with feet): 383×530×198 mm
Weight: 2 kg
Power supply: 230 V ~
Power consumption: 2 kW

7
2580 Ver. 3 –0918
ERP SPECIFICATIONS
Model Number
EH1710 / EH1710BLK
Item
Symbol
Value
Unit
Heat Output
Nominal Heat Output
Pnom
2,0
kW
Minimum Heat Output
(Indicitive)
Pmin
0,8
kW
Maximum Continuous
Heat Output
Pmax,c
2,0
kW
Auxiliary electricity Consumption
At nominal heat output
elmax
N/A
kW
At minimum heat
output
elmin
N/A
kW
At standby mode
elSB
N/A
kW
Type of heat input, for electric storage local space heaters only (single select)
manual heat charge control, with integrated thermostat
No
manual heat charge control with room and/or outdoor
temperature feedback
No
electronic heat charge control with room and/or outdoor
temperature feedback
No
fan assisted heat output
No
Type of heat output/room temperature control (single select)
single stage heat output and no room temperature control
No
Two or more manual stages, no room temperature control
No
with mechanic thermostat room temperature control
Yes
with electronic room temperature control
No
electronic room temperature control plus day timer
No
electronic room temperature control plus week timer
No

8
2580 Ver. 3 –0918
Other control options (multiple selections possible)
room temperature control, with presence detection
No
room temperature control, with open window detection
No
with distance control option
No
with adaptive start control
No
with working time limitation
No
with black bulb sensor
No
Contact Details
Prem-i-Air Appliances Ltd, Lancots Lane, St Helens,
WA9 3EX
SERVICE WARRANTY
Prem-i-Air guarantees the product free from defects in materials and workmanship
for a period of one years.
Should this unit be operated under conditions other than those recommended, at
voltages other than the voltage indicated on the unit, or any attempts made to
service or modify the unit, then the warranty will be rendered void.
The product you buy may sometimes differ slightly from illustrations. This warranty
is in addition to, and does not affect, your statutory rights.
If you have any problems with this product, please call our Help Desk on (0845)
459 4816.
Prem-i-Air Appliances Ltd.,
Lancots Lane,
Sutton,
St. Helens,
Merseyside.
WA9 3EX
Website: www.prem-i-air.co.uk