Pride Mobility VivaLIFT User manual

Included in this document: Hand Control Reference Guide,
Fabric Care, Assembly, Warranty, and Weight Capacity

2
Headrest
Lumbar
Back
Legrest
23
4
6
8
10
5
7
9
11
1
Hand Control referenCe Guide
NOTE: This quick reference guide offers basic hand control functions, general care instructions,
basic assembly information, warranty information and weight capacity information for your
chair. Before operating the chair, thoroughly read the owner’s manual and all other supplemental
documents for information on safety, basic operation and care and maintenance.
NOTE: These products are non-medical devices and are not meant to assist, treat, diagnose or
alleviate any medical condition or disability.
The illustrations reflect those hand controls with the highest level of functionality. The hand control you
receive may have fewer options, but basic functionality is the same.
The premier feature of the ViVaLiFT!™Power Recliner is that you have the ability to adjust your feet and back
independently to achieve your perfect position. For example, the seat back can recline until it is horizontal to the
floor. To achieve this, press and hold seatback recline button (“8”) (as shown in figure 1) until it is fully reclined.
Figure 1. Hand Control - Styles A and B
HAND CONTROL IDENTIFICATION KEY
1. USB PORT
Use to connect to/charge USB enabled
devices.
NOTE: iPhone users must use ONLY MFI-
certified cables when charging iPhone
devices.
2. HEADREST IN BUTTON
Press and hold to move headrest in.
3. HEADREST OUT BUTTON
Press and hold to move headrest out.
4. LUMBAR SUPPORT IN BUTTON
Press and hold to move lumbar support in.
5. LUMBAR SUPPORT OUT BUTTON
Press and hold to move lumbar support out.
AB
Back
23
6
8
7
9
1
6. UP BUTTON
Press and hold to return all chair power options to the neutral position, while lifting you into an upright
position.
7. DOWN BUTTON
Press and hold to lower chair to seated or reclined position.
8. SEATBACK RECLINE BUTTON
Press and hold to recline the seatback.
9. SEATBACK INCLINE BUTTON
Press and hold to raise the seatback.
10.LEG REST UP BUTTON
Press and hold to raise the legrest.
11.LEG REST DOWN BUTTON
Press and hold to lower the legrest.

3
Your ViValift!™Power reCliner
Figure 2. Chair Assembly
FABRIC CARE INSTRUCTIONS
The fabric covering this piece of furniture is very durable for everyday living. Clean only with water-
based shampoo or foam upholstery cleaner. Do not over wet. Do not use solvents to spot clean. Light
scrubbing will help with any tougher spots that may have developed. Always check a small spot of fabric
in an area that is unseen to be sure the cleaning agent being used will not discolor or fade the fabric’s
finishing. Let the chair air dry and vacuum for the best result.
CHAIR BACK ASSEMBLY
NOTE: If your chair is an Infinite model, refer to the assembly instructions provided with the
chair. For the 2-position model, the KD sleeves are located on the inside as shown in figure 2.
1. Check that the locking clip on the back of the chair is in the vertical position. Reposition if necessary.
2. Drape the hand control and cable over the chair base, then slide the back onto the base. Ensure the
hand control cable is routed through the rear of the chair.
NOTE: Depending on chair width, you may need to slide on one side of the back at a time. If this is the
case, level the chair-back before pressing down to lock into position.
3. Push firmly on the top of the back to lock into position. You must hear a click from each side of the chair to
ensure the back is locked in properly.
NOTE: Pull up on the chair-back to ensure that it is locked in place.

4
Your ViValift! Power reCliner
4. Plug in the lumbar and headrest connectors. If
your model is Headrest Only, you only need to
plug in the Headrest.
5. If your model has back wings, align the KD
sleeves, and slide the wing down into place,
see figure 3. Please note there is a label on
the brackets. Please assemble them as indi-
cated (1-1 and 2-2).
6. Connect the Power Transformer cable to the
corresponding plug coming from the back of
the chair, (see figure 2).
7. Connect the Power Cord into the Power Trans-
former (see figure 2).
8. Connect the power cord into an electrical outlet
near where the chair will be used.
Figure 3. Wing Back Installation

5
POWER HEADREST MOTOR CONNECTIONS
For initial use, troubleshooting or chair
reassembly, you may have to connect or
reconnect the power headrest motor wires.
1. Lay the seatback, face down, on the chair
base and route all cables through the wire
access point as shown.
Note: If you do not have a “Y” cable,
proceed to step 3.
2. For chairs equipped with a “Y” cable, plug
the seat base motor cable into the motor box
connector, and plug the hand control cable
and the seatback motor cable into the “Y”
cable connectors.
3. For chairs equipped with a control box, plug
the cable marked “A” into the control box’s
“A” port, and the cable marked “B” into the
control box’s “B” port. Plug the controller
cable into the center wire connector.
Figure 5. Power Headrest Cable Routing
Figure 6. Power Headrest Cable Connections
Figure 7. Power Headrest Control Box Connections
SEAT BASE MOTOR CABLE
HAND CONTROL CABLE
SEATBACKMOTORCABLE
AB
CONTROL BOX
Your ViValift! Power reCliner

6
notes

7
notes

Rev D/June 2021