Princess 332850 User manual
IMPORTANT SAFETY INSTRUCTIONS:
• Please use standard electricity service voltage (AC
220-240V,50/60Hz). Connecting to the incorrect voltage
may cause damage to the appliance and will invalidate the
warranty.
• Please don’t share the power supply with other high-
powered electric appliances.
• To avoid the electric shock, please don’t submerge the
appliance, plug or powercord in water or other liquids.
• Please don’t leave this appliance unattended while in
operation.
• Please ll the water tank to maximum before using and
observe the water level during use.
• Please don’t lay hose on the ground. Don’t wind hose. Don’t
operate the appliance if cord is damaged.
• Always keep the hose and nozzle elevated above the water
tank, so that the steam can be spouted conveniently. Never
insert any objects into any opening or hose.
• Please don’t cut or extend the steaming hose or power cord.
• Please don’t place the nozzle on any surface or appliance
power cord directly while it is hot or plugged in.
• Please be cautious about steam spraying out from the
nozzle. Do not direct nozzle at people or animals, in case the
steam exploding. Do not use the steamer on garments while
it is being worn.
• Please don’t lay or overturn the appliance when in use, or the
hot water will leakage.
• Turn o, unplug and allow the appliance to cool completely
for at least 30 minutes prior to draining the water tank and
water reservoir and storing.
• Always turn o and unplug unit before relling, draining,
cleaning or storing.
• For indoor use only.
• Please keep the appliance away from ammable materials
and chemicals.
• Please don’t ll the water tank with hot water or corrosive
cleaning agents which would cause damage. Distilled or
ltered water is strongly recommended.
• Only use Princess accessories on your Princess appliance. The
use of accessory attachments rather than those provided by
Princess may result in re, electric or irreversible damage to
the appliance.
• This appliance is not intended to be designed for children
and other persons whose physical, sensory or mental
capabilities is disabled or whom lack of sucient experience
or knowledge, please prevent them from using the appliance
without supervision or instruction by a person who can
ensure that they can use the appliance safely.
PARTS DESCRIPTION
1. Rotate Ironing Board
2. Collar Hanger
3. Water Tank
4. Telescopic Poles
5. Rotate Steam Nozzle
6. Body Base
7. Main Body
8. Fabric Boot Cap
9. Nozzle Hanger
PRODUCT SPECIFICATION
Water Tank Capacity 1.2L
Steam Output Time 60s
Input Voltage 220-240V~50/60Hz
Output Power 1920-2280W
FUNCTION FEATURES
Main Body Display Panel
Handle function buttons
According to your demand, press the rotate
button to adjust the nozzle 90° to the left.
Nozzle rotate button
On the top: Steaming Gear (with blue light on)
for continuous steam.
At bottom: Ironing Gear(with red light on). To
avoid damage to clothes caused by over time
ironing, if the switch is not turned on by user
for 15 minutes, this steamer will enter Standby
Mode automatically, with its indicator light
blinking, and steam stops working. Turn
on the Power ON/OFF switch again to let it
continue to work.
Sensor Switch on Main Body
When the steamer is working, steamer will
stop producing steam and continue to
heat-up when the Sensor Switch is pressed
down. If the Sensor Switch is pressed down,
with Standby Sleep Lamp on,for over 5
minute, buzzer will alarm once, buzzer will
alarm continually after 30 seconds and enter
Standby Mode. If the sensor switch is released
during this time, Standby Sleep Light goes o
and steamer resume to work.
Pressure release setting
When the pressure inside heater is
too high, the setting at the bottom
of main body would release
pressure automatically.
Auto pressure
release hole
Standby mode
PRODUCT INSTALLATION
STEP 1
Unlock both sides of the body base, insert the Telescopic Poles (the direction of
both poles needs to be accordant) into the base, and lock in place.
STEP 2
Adjust the telescopic poles to appropriate height, and lock in place.
STEP 3
Insert the collar hanger into the top of the ironing board.
STEP 4
Open the lock of the ironing board, install the board along the telescopic
poles, and lock in place.
STEP 5
Put the main body onto the base, then put the steamer nozzle onto
the recess above the main body.
STEP 6
Installation nished, product image as above.
INSTRUCTION FOR USE
STEP 1
Fill in the Water Tank and replace & tighten its cap.
STEP 2
Plug in, sound the main body beeps, then the power pilot lamp icker, and the
appliance switches to the stand by mode.
STEP 3
Touch the Power ON/OFF switch on Touching Screen on steamer, buzzer
will make a “bee” sound, steamer is turned on, and indicator light is on,
or is on(depends on the gear on Steam Nozzle Handle). Indicator light
blinks and steamer is ready to use after 48-second heat-up time, then
indicator light is on.
STEP 4
Steamer enters Working Mode after 48 seconds. Set the gear on Steam Nozzle
Handle upwards to enter Steaming Gear, with blue light on and on, steam will
spray out. Set the gear on Steam Nozzle Handle downwards to enter Ironing
Gear, with the red light on and on, no steam is produced.
STEP 5
Keep pressing on the red button behind the ironing board, so that you can
adjust the slope angle of the ironing board at random.
STEP 6
Ready for garment steaming.
MAINTENANCE AND CLEANING
STEP 1
Touch the Power ON/OFF switch on Touching Screen on steamer to turn o the
steamer, buzzer will make a “bee” sound, steamer is turned o, Indicator Light
blinks and steamer is under Standby Mode. Pull out the Plug and wait for at
least 30 minutes till the steamer cools down completely.
STEP 2
Take out the water tank and drug out the water. Adjust the telescopic poles to
appropriate place for easy storage.
DISASSEMBLY INSTRUCTION FOR IRONING CLOTH
STEP 1
Unlock the ironing board on both sides.And remove the ironing board with
both hands.
STEP 2
Remove the collar hanger and the decoration board.
STEP 3
Loosen the string behind the ironing board, then remove the ironing cloth.
STEP 4
Cover the ironing board with new ironing cloth and lace in place. Pull the
string upward and x it to the hook. Then install the decoration board back in
place, the ironing board is ready for use.
ACCESSORIES INSTRUCTION FOR USE
Rotate nozzle
mode changing-over
Recommended Recommended for
for horizontal ironing vertical or oblique ironing
Fabric Boot Cap Installation
Warm prompt: To prevent the fabric from being damaged by the high
temperature, please choose to use the boot cap in appropriate according to
how the temperature resistant of the fabric is.
Attention: When the appliance is still operating or the nozzle panel doesn't
drop to room temperature, please don't install or dismantle the boot cap so as
not to be scalded.
Nozzle Hanger Installation
Install the hanger to the middle of the telescopic poles, adjust it to appropriate
height and then lock in place.
To prevent fabric and ironing
board from being scalded, please
don't put the nozzle on the same
position for more than 30 seconds.
Use of Rotate Ironing Board
Attention: Be cautious of being hurt while adjusting the ironing board.
Separated base
Use of creel
TROUBLE SHOOTING
Problem Reason Solution
Unit fails to work.
Pilot lamp does not
illuminate
• The unit is not
plugged in
• House hold power
system problem /
fuse is blown
• Plug in the unit
• Call a qualied
electrician for help
Unit fails to steam Pilot
lamp illuminates
• Water Tank is empty
• Thermal cut-o is
damaged
• Thermostat is
damaged
• Switch on Handle
or Sensor Switch on
Main Body or Water
pump is damaged
• Rell the Water Tank
• Call a qualied
electrician for help.
• Call a qualied
electrician for help.
• Call a qualied
electrician for help
Nozzle panel heating
and works normally,
Pilot lamp does not
illuminates
Pilot lamp is broken Call a qualied
electrician for help
Less steam spraying out Voltage is too low Please avoid to use
this appliance during
the surge in electricity
demand
Nozzle has water
leakage problem
• It is normal that a
few of water sprayed
out from the nozzle
when turn it on.
• Heating pot does not
work
• This phenomenon
will distinguish after
one minute
• Call a qualied
electrician for help
Water tank leakage • Water tank's screw is
not tightened
• Water tank is broken
• Tighten the screw of
water tank
• Call a qualied
electrician for help
Appliance leakage Inside water tube is
broken
Call a qualied
electrician for help
Water tank is out of
shape
Fill the tank with hot
water
Call a qualied
electrician for help
ENVIRONMENT
This appliance should not be put into the domestic garbage at the end
of its durability, but must be oered at a central point for the recycling
of electric and electronic domestic appliances. This symbol on the appliance,
instruction manual and packaging puts your attention to this important issue.
The materials used in this appliance can be recycled. By recycling of used
domestic appliances you contribute an important push to the protection of
our environment. Ask your local authorities for information regarding the point
of recollection.
EN Instruction manual
service.princess.info
© Princess 2017
PARTS DESCRIPTION /
Garment steamer
EN Instruction manual
AR
1
4
5
7 8 9
3
6
2
To avoid being scalded, please don't rotate the
nozzle when the nozzle panel doesn't drop down to
the room temperature, nor during operation either.
Be cautious about the steam
spraying out from the hole when
the appliance is operating, so as
not to be scalded.
If the appliance enters
standby mode for less
than 3 minutes, reboot the
appliance, it will return to
work without pre-heating.
If the appliance enters
standby mode for more
than 3 minutes, reboot
the appliance, it needs to
pre-heat for 25 seconds to
return to work.
If the appliance enters
standby mode for more
than 5 minutes, reboot the
appliance, it needs to pre-
heat for 48 seconds to return
to work.
332850
- Children being supervised not to play with the appliance
- The iron must not be left unattended while it is connected
to the supply mains
- The plug must be removed from the socket-outlet before
filled with water (for
steam irons
and irons incorporating means for
spraying water)
- The iron must be used and rested on a flat, stable surface
- When placing the iron on its stand, ensure that the
surface on which the stand is
- The iron is not to be used if it has been dropped, if there are visible signs of
-Care should be taken when using the appliance due to the emission of steam
-If the supply cord is damaged, it must be replaced by manufacturer, its service
Agent or similarly qualified person to avoid hazard.
the water reservoir is
placed is stable
damage or if it is leaking
IMPORTANT SAFETY INSTRUCTIONS:
• Please use standard electricity service voltage (AC
220-240V,50/60Hz). Connecting to the incorrect voltage
may cause damage to the appliance and will invalidate the
warranty.
• Please don’t share the power supply with other high-
powered electric appliances.
• To avoid the electric shock, please don’t submerge the
appliance, plug or powercord in water or other liquids.
• Please don’t leave this appliance unattended while in
operation.
• Please ll the water tank to maximum before using and
observe the water level during use.
• Please don’t lay hose on the ground. Don’t wind hose. Don’t
operate the appliance if cord is damaged.
• Always keep the hose and nozzle elevated above the water
tank, so that the steam can be spouted conveniently. Never
insert any objects into any opening or hose.
• Please don’t cut or extend the steaming hose or power cord.
• Please don’t place the nozzle on any surface or appliance
power cord directly while it is hot or plugged in.
• Please be cautious about steam spraying out from the
nozzle. Do not direct nozzle at people or animals, in case the
steam exploding. Do not use the steamer on garments while
it is being worn.
• Please don’t lay or overturn the appliance when in use, or the
hot water will leakage.
• Turn o, unplug and allow the appliance to cool completely
for at least 30 minutes prior to draining the water tank and
water reservoir and storing.
• Always turn o and unplug unit before relling, draining,
cleaning or storing.
• For indoor use only.
• Please keep the appliance away from ammable materials
and chemicals.
• Please don’t ll the water tank with hot water or corrosive
cleaning agents which would cause damage. Distilled or
ltered water is strongly recommended.
• Only use Princess accessories on your Princess appliance. The
use of accessory attachments rather than those provided by
Princess may result in re, electric or irreversible damage to
the appliance.
• This appliance is not intended to be designed for children
and other persons whose physical, sensory or mental
capabilities is disabled or whom lack of sucient experience
or knowledge, please prevent them from using the appliance
without supervision or instruction by a person who can
ensure that they can use the appliance safely.
PARTS DESCRIPTION
1. Rotate Ironing Board
2. Collar Hanger
3. Water Tank
4. Telescopic Poles
5. Rotate Steam Nozzle
6. Body Base
7. Main Body
8. Fabric Boot Cap
9. Nozzle Hanger
PRODUCT SPECIFICATION
Water Tank Capacity 1.2L
Steam Output Time 60s
Input Voltage 220-240V~50/60Hz
Output Power 1920-2280W
FUNCTION FEATURES
Main Body Display Panel
Handle function buttons
According to your demand, press the rotate
button to adjust the nozzle 90° to the left.
Nozzle rotate button
On the top: Steaming Gear (with blue light on)
for continuous steam.
At bottom: Ironing Gear(with red light on). To
avoid damage to clothes caused by over time
ironing, if the switch is not turned on by user
for 15 minutes, this steamer will enter Standby
Mode automatically, with its indicator light
blinking, and steam stops working. Turn
on the Power ON/OFF switch again to let it
continue to work.
Sensor Switch on Main Body
When the steamer is working, steamer will
stop producing steam and continue to
heat-up when the Sensor Switch is pressed
down. If the Sensor Switch is pressed down,
with Standby Sleep Lamp on,for over 5
minute, buzzer will alarm once, buzzer will
alarm continually after 30 seconds and enter
Standby Mode. If the sensor switch is released
during this time, Standby Sleep Light goes o
and steamer resume to work.
Pressure release setting
When the pressure inside heater is
too high, the setting at the bottom
of main body would release
pressure automatically.
Auto pressure
release hole
Standby mode
PRODUCT INSTALLATION
STEP 1
Unlock both sides of the body base, insert the Telescopic Poles (the direction of
both poles needs to be accordant) into the base, and lock in place.
STEP 2
Adjust the telescopic poles to appropriate height, and lock in place.
STEP 3
Insert the collar hanger into the top of the ironing board.
STEP 4
Open the lock of the ironing board, install the board along the telescopic
poles, and lock in place.
STEP 5
Put the main body onto the base, then put the steamer nozzle onto
the recess above the main body.
STEP 6
Installation nished, product image as above.
INSTRUCTION FOR USE
STEP 1
Fill in the Water Tank and replace & tighten its cap.
STEP 2
Plug in, sound the main body beeps, then the power pilot lamp icker, and the
appliance switches to the stand by mode.
STEP 3
Touch the Power ON/OFF switch on Touching Screen on steamer, buzzer
will make a “bee” sound, steamer is turned on, and indicator light is on,
or is on(depends on the gear on Steam Nozzle Handle). Indicator light
blinks and steamer is ready to use after 48-second heat-up time, then
indicator light is on.
STEP 4
Steamer enters Working Mode after 48 seconds. Set the gear on Steam Nozzle
Handle upwards to enter Steaming Gear, with blue light on and on, steam will
spray out. Set the gear on Steam Nozzle Handle downwards to enter Ironing
Gear, with the red light on and on, no steam is produced.
STEP 5
Keep pressing on the red button behind the ironing board, so that you can
adjust the slope angle of the ironing board at random.
STEP 6
Ready for garment steaming.
MAINTENANCE AND CLEANING
STEP 1
Touch the Power ON/OFF switch on Touching Screen on steamer to turn o the
steamer, buzzer will make a “bee” sound, steamer is turned o, Indicator Light
blinks and steamer is under Standby Mode. Pull out the Plug and wait for at
least 30 minutes till the steamer cools down completely.
STEP 2
Take out the water tank and drug out the water. Adjust the telescopic poles to
appropriate place for easy storage.
DISASSEMBLY INSTRUCTION FOR IRONING CLOTH
STEP 1
Unlock the ironing board on both sides.And remove the ironing board with
both hands.
STEP 2
Remove the collar hanger and the decoration board.
STEP 3
Loosen the string behind the ironing board, then remove the ironing cloth.
STEP 4
Cover the ironing board with new ironing cloth and lace in place. Pull the
string upward and x it to the hook. Then install the decoration board back in
place, the ironing board is ready for use.
ACCESSORIES INSTRUCTION FOR USE
Rotate nozzle
mode changing-over
Recommended Recommended for
for horizontal ironing vertical or oblique ironing
Fabric Boot Cap Installation
Warm prompt: To prevent the fabric from being damaged by the high
temperature, please choose to use the boot cap in appropriate according to
how the temperature resistant of the fabric is.
Attention: When the appliance is still operating or the nozzle panel doesn't
drop to room temperature, please don't install or dismantle the boot cap so as
not to be scalded.
Nozzle Hanger Installation
Install the hanger to the middle of the telescopic poles, adjust it to appropriate
height and then lock in place.
To prevent fabric and ironing
board from being scalded, please
don't put the nozzle on the same
position for more than 30 seconds.
Use of Rotate Ironing Board
Attention: Be cautious of being hurt while adjusting the ironing board.
Separated base
Use of creel
TROUBLE SHOOTING
Problem Reason Solution
Unit fails to work.
Pilot lamp does not
illuminate
• The unit is not
plugged in
• House hold power
system problem /
fuse is blown
• Plug in the unit
• Call a qualied
electrician for help
Unit fails to steam Pilot
lamp illuminates
• Water Tank is empty
• Thermal cut-o is
damaged
• Thermostat is
damaged
• Switch on Handle
or Sensor Switch on
Main Body or Water
pump is damaged
• Rell the Water Tank
• Call a qualied
electrician for help.
• Call a qualied
electrician for help.
• Call a qualied
electrician for help
Nozzle panel heating
and works normally,
Pilot lamp does not
illuminates
Pilot lamp is broken Call a qualied
electrician for help
Less steam spraying out Voltage is too low Please avoid to use
this appliance during
the surge in electricity
demand
Nozzle has water
leakage problem
• It is normal that a
few of water sprayed
out from the nozzle
when turn it on.
• Heating pot does not
work
• This phenomenon
will distinguish after
one minute
• Call a qualied
electrician for help
Water tank leakage • Water tank's screw is
not tightened
• Water tank is broken
• Tighten the screw of
water tank
• Call a qualied
electrician for help
Appliance leakage Inside water tube is
broken
Call a qualied
electrician for help
Water tank is out of
shape
Fill the tank with hot
water
Call a qualied
electrician for help
ENVIRONMENT
This appliance should not be put into the domestic garbage at the end
of its durability, but must be oered at a central point for the recycling
of electric and electronic domestic appliances. This symbol on the appliance,
instruction manual and packaging puts your attention to this important issue.
The materials used in this appliance can be recycled. By recycling of used
domestic appliances you contribute an important push to the protection of
our environment. Ask your local authorities for information regarding the point
of recollection.
EN Instruction manual
service.princess.info
© Princess 2017
PARTS DESCRIPTION /
Garment steamer
EN Instruction manual
AR
1
4
5
7 8 9
3
6
2
To avoid being scalded, please don't rotate the
nozzle when the nozzle panel doesn't drop down to
the room temperature, nor during operation either.
Be cautious about the steam
spraying out from the hole when
the appliance is operating, so as
not to be scalded.
If the appliance enters
standby mode for less
than 3 minutes, reboot the
appliance, it will return to
work without pre-heating.
If the appliance enters
standby mode for more
than 3 minutes, reboot
the appliance, it needs to
pre-heat for 25 seconds to
return to work.
If the appliance enters
standby mode for more
than 5 minutes, reboot the
appliance, it needs to pre-
heat for 48 seconds to return
to work.
332850
- Children being supervised not to play with the appliance
- The iron must not be left unattended while it is connected
to the supply mains
- The plug must be removed from the socket-outlet before
filled with water (for
steam irons
and irons incorporating means for
spraying water)
- The iron must be used and rested on a flat, stable surface
- When placing the iron on its stand, ensure that the
surface on which the stand is
- The iron is not to be used if it has been dropped, if there are visible signs of
-Care should be taken when using the appliance due to the emission of steam
-If the supply cord is damaged, it must be replaced by manufacturer, its service
Agent or similarly qualified person to avoid hazard.
the water reservoir is
placed is stable
damage or if it is leaking
IMPORTANT SAFETY INSTRUCTIONS:
• Please use standard electricity service voltage (AC
220-240V,50/60Hz). Connecting to the incorrect voltage
may cause damage to the appliance and will invalidate the
warranty.
• Please don’t share the power supply with other high-
powered electric appliances.
• To avoid the electric shock, please don’t submerge the
appliance, plug or powercord in water or other liquids.
• Please don’t leave this appliance unattended while in
operation.
• Please ll the water tank to maximum before using and
observe the water level during use.
• Please don’t lay hose on the ground. Don’t wind hose. Don’t
operate the appliance if cord is damaged.
• Always keep the hose and nozzle elevated above the water
tank, so that the steam can be spouted conveniently. Never
insert any objects into any opening or hose.
• Please don’t cut or extend the steaming hose or power cord.
• Please don’t place the nozzle on any surface or appliance
power cord directly while it is hot or plugged in.
• Please be cautious about steam spraying out from the
nozzle. Do not direct nozzle at people or animals, in case the
steam exploding. Do not use the steamer on garments while
it is being worn.
• Please don’t lay or overturn the appliance when in use, or the
hot water will leakage.
• Turn o, unplug and allow the appliance to cool completely
for at least 30 minutes prior to draining the water tank and
water reservoir and storing.
• Always turn o and unplug unit before relling, draining,
cleaning or storing.
• For indoor use only.
• Please keep the appliance away from ammable materials
and chemicals.
• Please don’t ll the water tank with hot water or corrosive
cleaning agents which would cause damage. Distilled or
ltered water is strongly recommended.
• Only use Princess accessories on your Princess appliance. The
use of accessory attachments rather than those provided by
Princess may result in re, electric or irreversible damage to
the appliance.
• This appliance is not intended to be designed for children
and other persons whose physical, sensory or mental
capabilities is disabled or whom lack of sucient experience
or knowledge, please prevent them from using the appliance
without supervision or instruction by a person who can
ensure that they can use the appliance safely.
PARTS DESCRIPTION
1. Rotate Ironing Board
2. Collar Hanger
3. Water Tank
4. Telescopic Poles
5. Rotate Steam Nozzle
6. Body Base
7. Main Body
8. Fabric Boot Cap
9. Nozzle Hanger
PRODUCT SPECIFICATION
Water Tank Capacity 1.2L
Steam Output Time 60s
Input Voltage 220-240V~50/60Hz
Output Power 1920-2280W
FUNCTION FEATURES
Main Body Display Panel
Handle function buttons
According to your demand, press the rotate
button to adjust the nozzle 90° to the left.
Nozzle rotate button
On the top: Steaming Gear (with blue light on)
for continuous steam.
At bottom: Ironing Gear(with red light on). To
avoid damage to clothes caused by over time
ironing, if the switch is not turned on by user
for 15 minutes, this steamer will enter Standby
Mode automatically, with its indicator light
blinking, and steam stops working. Turn
on the Power ON/OFF switch again to let it
continue to work.
Sensor Switch on Main Body
When the steamer is working, steamer will
stop producing steam and continue to
heat-up when the Sensor Switch is pressed
down. If the Sensor Switch is pressed down,
with Standby Sleep Lamp on,for over 5
minute, buzzer will alarm once, buzzer will
alarm continually after 30 seconds and enter
Standby Mode. If the sensor switch is released
during this time, Standby Sleep Light goes o
and steamer resume to work.
Pressure release setting
When the pressure inside heater is
too high, the setting at the bottom
of main body would release
pressure automatically.
Auto pressure
release hole
Standby mode
PRODUCT INSTALLATION
STEP 1
Unlock both sides of the body base, insert the Telescopic Poles (the direction of
both poles needs to be accordant) into the base, and lock in place.
STEP 2
Adjust the telescopic poles to appropriate height, and lock in place.
STEP 3
Insert the collar hanger into the top of the ironing board.
STEP 4
Open the lock of the ironing board, install the board along the telescopic
poles, and lock in place.
STEP 5
Put the main body onto the base, then put the steamer nozzle onto
the recess above the main body.
STEP 6
Installation nished, product image as above.
INSTRUCTION FOR USE
STEP 1
Fill in the Water Tank and replace & tighten its cap.
STEP 2
Plug in, sound the main body beeps, then the power pilot lamp icker, and the
appliance switches to the stand by mode.
STEP 3
Touch the Power ON/OFF switch on Touching Screen on steamer, buzzer
will make a “bee” sound, steamer is turned on, and indicator light is on,
or is on(depends on the gear on Steam Nozzle Handle). Indicator light
blinks and steamer is ready to use after 48-second heat-up time, then
indicator light is on.
STEP 4
Steamer enters Working Mode after 48 seconds. Set the gear on Steam Nozzle
Handle upwards to enter Steaming Gear, with blue light on and on, steam will
spray out. Set the gear on Steam Nozzle Handle downwards to enter Ironing
Gear, with the red light on and on, no steam is produced.
STEP 5
Keep pressing on the red button behind the ironing board, so that you can
adjust the slope angle of the ironing board at random.
STEP 6
Ready for garment steaming.
MAINTENANCE AND CLEANING
STEP 1
Touch the Power ON/OFF switch on Touching Screen on steamer to turn o the
steamer, buzzer will make a “bee”sound, steamer is turned o, Indicator Light
blinks and steamer is under Standby Mode. Pull out the Plug and wait for at
least 30 minutes till the steamer cools down completely.
STEP 2
Take out the water tank and drug out the water. Adjust the telescopic poles to
appropriate place for easy storage.
DISASSEMBLY INSTRUCTION FOR IRONING CLOTH
STEP 1
Unlock the ironing board on both sides.And remove the ironing board with
both hands.
STEP 2
Remove the collar hanger and the decoration board.
STEP 3
Loosen the string behind the ironing board, then remove the ironing cloth.
STEP 4
Cover the ironing board with new ironing cloth and lace in place. Pull the
string upward and x it to the hook. Then install the decoration board back in
place, the ironing board is ready for use.
ACCESSORIES INSTRUCTION FOR USE
Rotate nozzle
mode changing-over
Recommended Recommended for
for horizontal ironing vertical or oblique ironing
Fabric Boot Cap Installation
Warm prompt: To prevent the fabric from being damaged by the high
temperature, please choose to use the boot cap in appropriate according to
how the temperature resistant of the fabric is.
Attention: When the appliance is still operating or the nozzle panel doesn't
drop to room temperature, please don't install or dismantle the boot cap so as
not to be scalded.
Nozzle Hanger Installation
Install the hanger to the middle of the telescopic poles, adjust it to appropriate
height and then lock in place.
To prevent fabric and ironing
board from being scalded, please
don't put the nozzle on the same
position for more than 30 seconds.
Use of Rotate Ironing Board
Attention: Be cautious of being hurt while adjusting the ironing board.
Separated base
Use of creel
TROUBLE SHOOTING
Problem Reason Solution
Unit fails to work.
Pilot lamp does not
illuminate
• The unit is not
plugged in
• House hold power
system problem /
fuse is blown
• Plug in the unit
• Call a qualied
electrician for help
Unit fails to steam Pilot
lamp illuminates
• Water Tank is empty
• Thermal cut-o is
damaged
• Thermostat is
damaged
• Switch on Handle
or Sensor Switch on
Main Body or Water
pump is damaged
• Rell the Water Tank
• Call a qualied
electrician for help.
• Call a qualied
electrician for help.
• Call a qualied
electrician for help
Nozzle panel heating
and works normally,
Pilot lamp does not
illuminates
Pilot lamp is broken Call a qualied
electrician for help
Less steam spraying out Voltage is too low Please avoid to use
this appliance during
the surge in electricity
demand
Nozzle has water
leakage problem
• It is normal that a
few of water sprayed
out from the nozzle
when turn it on.
• Heating pot does not
work
• This phenomenon
will distinguish after
one minute
• Call a qualied
electrician for help
Water tank leakage • Water tank's screw is
not tightened
• Water tank is broken
• Tighten the screw of
water tank
• Call a qualied
electrician for help
Appliance leakage Inside water tube is
broken
Call a qualied
electrician for help
Water tank is out of
shape
Fill the tank with hot
water
Call a qualied
electrician for help
ENVIRONMENT
This appliance should not be put into the domestic garbage at the end
of its durability, but must be oered at a central point for the recycling
of electric and electronic domestic appliances. This symbol on the appliance,
instruction manual and packaging puts your attention to this important issue.
The materials used in this appliance can be recycled. By recycling of used
domestic appliances you contribute an important push to the protection of
our environment. Ask your local authorities for information regarding the point
of recollection.
EN Instruction manual
service.princess.info
© Princess 2017
PARTS DESCRIPTION /
Garment steamer
EN Instruction manual
AR
1
4
5
7 8 9
3
6
2
To avoid being scalded, please don't rotate the
nozzle when the nozzle panel doesn't drop down to
the room temperature, nor during operation either.
Be cautious about the steam
spraying out from the hole when
the appliance is operating, so as
not to be scalded.
If the appliance enters
standby mode for less
than 3 minutes, reboot the
appliance, it will return to
work without pre-heating.
If the appliance enters
standby mode for more
than 3 minutes, reboot
the appliance, it needs to
pre-heat for 25 seconds to
return to work.
If the appliance enters
standby mode for more
than 5 minutes, reboot the
appliance, it needs to pre-
heat for 48 seconds to return
to work.
332850
- Children being supervised not to play with the appliance
- The iron must not be left unattended while it is connected
to the supply mains
- The plug must be removed from the socket-outlet before
filled with water (for
steam irons
and irons incorporating means for
spraying water)
- The iron must be used and rested on a flat, stable surface
- When placing the iron on its stand, ensure that the
surface on which the stand is
- The iron is not to be used if it has been dropped, if there are visible signs of
-Care should be taken when using the appliance due to the emission of steam
-If the supply cord is damaged, it must be replaced by manufacturer, its service
Agent or similarly qualified person to avoid hazard.
the water reservoir is
placed is stable
damage or if it is leaking
IMPORTANT SAFETY INSTRUCTIONS:
• Please use standard electricity service voltage (AC
220-240V,50/60Hz). Connecting to the incorrect voltage
may cause damage to the appliance and will invalidate the
warranty.
• Please don’t share the power supply with other high-
powered electric appliances.
• To avoid the electric shock, please don’t submerge the
appliance, plug or powercord in water or other liquids.
• Please don’t leave this appliance unattended while in
operation.
• Please ll the water tank to maximum before using and
observe the water level during use.
• Please don’t lay hose on the ground. Don’t wind hose. Don’t
operate the appliance if cord is damaged.
• Always keep the hose and nozzle elevated above the water
tank, so that the steam can be spouted conveniently. Never
insert any objects into any opening or hose.
• Please don’t cut or extend the steaming hose or power cord.
• Please don’t place the nozzle on any surface or appliance
power cord directly while it is hot or plugged in.
• Please be cautious about steam spraying out from the
nozzle. Do not direct nozzle at people or animals, in case the
steam exploding. Do not use the steamer on garments while
it is being worn.
• Please don’t lay or overturn the appliance when in use, or the
hot water will leakage.
• Turn o, unplug and allow the appliance to cool completely
for at least 30 minutes prior to draining the water tank and
water reservoir and storing.
• Always turn o and unplug unit before relling, draining,
cleaning or storing.
• For indoor use only.
• Please keep the appliance away from ammable materials
and chemicals.
• Please don’t ll the water tank with hot water or corrosive
cleaning agents which would cause damage. Distilled or
ltered water is strongly recommended.
• Only use Princess accessories on your Princess appliance. The
use of accessory attachments rather than those provided by
Princess may result in re, electric or irreversible damage to
the appliance.
• This appliance is not intended to be designed for children
and other persons whose physical, sensory or mental
capabilities is disabled or whom lack of sucient experience
or knowledge, please prevent them from using the appliance
without supervision or instruction by a person who can
ensure that they can use the appliance safely.
PARTS DESCRIPTION
1. Rotate Ironing Board
2. Collar Hanger
3. Water Tank
4. Telescopic Poles
5. Rotate Steam Nozzle
6. Body Base
7. Main Body
8. Fabric Boot Cap
9. Nozzle Hanger
PRODUCT SPECIFICATION
Water Tank Capacity 1.2L
Steam Output Time 60s
Input Voltage 220-240V~50/60Hz
Output Power 1920-2280W
FUNCTION FEATURES
Main Body Display Panel
Handle function buttons
According to your demand, press the rotate
button to adjust the nozzle 90° to the left.
Nozzle rotate button
On the top: Steaming Gear (with blue light on)
for continuous steam.
At bottom: Ironing Gear(with red light on). To
avoid damage to clothes caused by over time
ironing, if the switch is not turned on by user
for 15 minutes, this steamer will enter Standby
Mode automatically, with its indicator light
blinking, and steam stops working. Turn
on the Power ON/OFF switch again to let it
continue to work.
Sensor Switch on Main Body
When the steamer is working, steamer will
stop producing steam and continue to
heat-up when the Sensor Switch is pressed
down. If the Sensor Switch is pressed down,
with Standby Sleep Lamp on,for over 5
minute, buzzer will alarm once, buzzer will
alarm continually after 30 seconds and enter
Standby Mode. If the sensor switch is released
during this time, Standby Sleep Light goes o
and steamer resume to work.
Pressure release setting
When the pressure inside heater is
too high, the setting at the bottom
of main body would release
pressure automatically.
Auto pressure
release hole
Standby mode
PRODUCT INSTALLATION
STEP 1
Unlock both sides of the body base, insert the Telescopic Poles (the direction of
both poles needs to be accordant) into the base, and lock in place.
STEP 2
Adjust the telescopic poles to appropriate height, and lock in place.
STEP 3
Insert the collar hanger into the top of the ironing board.
STEP 4
Open the lock of the ironing board, install the board along the telescopic
poles, and lock in place.
STEP 5
Put the main body onto the base, then put the steamer nozzle onto
the recess above the main body.
STEP 6
Installation nished, product image as above.
INSTRUCTION FOR USE
STEP 1
Fill in the Water Tank and replace & tighten its cap.
STEP 2
Plug in, sound the main body beeps, then the power pilot lamp icker, and the
appliance switches to the stand by mode.
STEP 3
Touch the Power ON/OFF switch on Touching Screen on steamer, buzzer
will make a “bee” sound, steamer is turned on, and indicator light is on,
or is on(depends on the gear on Steam Nozzle Handle). Indicator light
blinks and steamer is ready to use after 48-second heat-up time, then
indicator light is on.
STEP 4
Steamer enters Working Mode after 48 seconds. Set the gear on Steam Nozzle
Handle upwards to enter Steaming Gear, with blue light on and on, steam will
spray out. Set the gear on Steam Nozzle Handle downwards to enter Ironing
Gear, with the red light on and on, no steam is produced.
STEP 5
Keep pressing on the red button behind the ironing board, so that you can
adjust the slope angle of the ironing board at random.
STEP 6
Ready for garment steaming.
MAINTENANCE AND CLEANING
STEP 1
Touch the Power ON/OFF switch on Touching Screen on steamer to turn o the
steamer, buzzer will make a “bee”sound, steamer is turned o, Indicator Light
blinks and steamer is under Standby Mode. Pull out the Plug and wait for at
least 30 minutes till the steamer cools down completely.
STEP 2
Take out the water tank and drug out the water. Adjust the telescopic poles to
appropriate place for easy storage.
DISASSEMBLY INSTRUCTION FOR IRONING CLOTH
STEP 1
Unlock the ironing board on both sides.And remove the ironing board with
both hands.
STEP 2
Remove the collar hanger and the decoration board.
STEP 3
Loosen the string behind the ironing board, then remove the ironing cloth.
STEP 4
Cover the ironing board with new ironing cloth and lace in place. Pull the
string upward and x it to the hook. Then install the decoration board back in
place, the ironing board is ready for use.
ACCESSORIES INSTRUCTION FOR USE
Rotate nozzle
mode changing-over
Recommended Recommended for
for horizontal ironing vertical or oblique ironing
Fabric Boot Cap Installation
Warm prompt: To prevent the fabric from being damaged by the high
temperature, please choose to use the boot cap in appropriate according to
how the temperature resistant of the fabric is.
Attention: When the appliance is still operating or the nozzle panel doesn't
drop to room temperature, please don't install or dismantle the boot cap so as
not to be scalded.
Nozzle Hanger Installation
Install the hanger to the middle of the telescopic poles, adjust it to appropriate
height and then lock in place.
To prevent fabric and ironing
board from being scalded, please
don't put the nozzle on the same
position for more than 30 seconds.
Use of Rotate Ironing Board
Attention: Be cautious of being hurt while adjusting the ironing board.
Separated base
Use of creel
TROUBLE SHOOTING
Problem Reason Solution
Unit fails to work.
Pilot lamp does not
illuminate
• The unit is not
plugged in
• House hold power
system problem /
fuse is blown
• Plug in the unit
• Call a qualied
electrician for help
Unit fails to steam Pilot
lamp illuminates
• Water Tank is empty
• Thermal cut-o is
damaged
• Thermostat is
damaged
• Switch on Handle
or Sensor Switch on
Main Body or Water
pump is damaged
• Rell the Water Tank
• Call a qualied
electrician for help.
• Call a qualied
electrician for help.
• Call a qualied
electrician for help
Nozzle panel heating
and works normally,
Pilot lamp does not
illuminates
Pilot lamp is broken Call a qualied
electrician for help
Less steam spraying out Voltage is too low Please avoid to use
this appliance during
the surge in electricity
demand
Nozzle has water
leakage problem
• It is normal that a
few of water sprayed
out from the nozzle
when turn it on.
• Heating pot does not
work
• This phenomenon
will distinguish after
one minute
• Call a qualied
electrician for help
Water tank leakage • Water tank's screw is
not tightened
• Water tank is broken
• Tighten the screw of
water tank
• Call a qualied
electrician for help
Appliance leakage Inside water tube is
broken
Call a qualied
electrician for help
Water tank is out of
shape
Fill the tank with hot
water
Call a qualied
electrician for help
ENVIRONMENT
This appliance should not be put into the domestic garbage at the end
of its durability, but must be oered at a central point for the recycling
of electric and electronic domestic appliances. This symbol on the appliance,
instruction manual and packaging puts your attention to this important issue.
The materials used in this appliance can be recycled. By recycling of used
domestic appliances you contribute an important push to the protection of
our environment. Ask your local authorities for information regarding the point
of recollection.
EN Instruction manual
service.princess.info
© Princess 2017
PARTS DESCRIPTION /
Garment steamer
EN Instruction manual
AR
1
4
5
7 8 9
3
6
2
To avoid being scalded, please don't rotate the
nozzle when the nozzle panel doesn't drop down to
the room temperature, nor during operation either.
Be cautious about the steam
spraying out from the hole when
the appliance is operating, so as
not to be scalded.
If the appliance enters
standby mode for less
than 3 minutes, reboot the
appliance, it will return to
work without pre-heating.
If the appliance enters
standby mode for more
than 3 minutes, reboot
the appliance, it needs to
pre-heat for 25 seconds to
return to work.
If the appliance enters
standby mode for more
than 5 minutes, reboot the
appliance, it needs to pre-
heat for 48 seconds to return
to work.
332850
- Children being supervised not to play with the appliance
- The iron must not be left unattended while it is connected
to the supply mains
- The plug must be removed from the socket-outlet before
filled with water (for
steam irons
and irons incorporating means for
spraying water)
- The iron must be used and rested on a flat, stable surface
- When placing the iron on its stand, ensure that the
surface on which the stand is
- The iron is not to be used if it has been dropped, if there are visible signs of
-Care should be taken when using the appliance due to the emission of steam
-If the supply cord is damaged, it must be replaced by manufacturer, its service
Agent or similarly qualified person to avoid hazard.
the water reservoir is
placed is stable
damage or if it is leaking
IMPORTANT SAFETY INSTRUCTIONS:
• Please use standard electricity service voltage (AC
220-240V,50/60Hz). Connecting to the incorrect voltage
may cause damage to the appliance and will invalidate the
warranty.
• Please don’t share the power supply with other high-
powered electric appliances.
• To avoid the electric shock, please don’t submerge the
appliance, plug or powercord in water or other liquids.
• Please don’t leave this appliance unattended while in
operation.
• Please ll the water tank to maximum before using and
observe the water level during use.
• Please don’t lay hose on the ground. Don’t wind hose. Don’t
operate the appliance if cord is damaged.
• Always keep the hose and nozzle elevated above the water
tank, so that the steam can be spouted conveniently. Never
insert any objects into any opening or hose.
• Please don’t cut or extend the steaming hose or power cord.
• Please don’t place the nozzle on any surface or appliance
power cord directly while it is hot or plugged in.
• Please be cautious about steam spraying out from the
nozzle. Do not direct nozzle at people or animals, in case the
steam exploding. Do not use the steamer on garments while
it is being worn.
• Please don’t lay or overturn the appliance when in use, or the
hot water will leakage.
• Turn o, unplug and allow the appliance to cool completely
for at least 30 minutes prior to draining the water tank and
water reservoir and storing.
• Always turn o and unplug unit before relling, draining,
cleaning or storing.
• For indoor use only.
• Please keep the appliance away from ammable materials
and chemicals.
• Please don’t ll the water tank with hot water or corrosive
cleaning agents which would cause damage. Distilled or
ltered water is strongly recommended.
• Only use Princess accessories on your Princess appliance. The
use of accessory attachments rather than those provided by
Princess may result in re, electric or irreversible damage to
the appliance.
• This appliance is not intended to be designed for children
and other persons whose physical, sensory or mental
capabilities is disabled or whom lack of sucient experience
or knowledge, please prevent them from using the appliance
without supervision or instruction by a person who can
ensure that they can use the appliance safely.
PARTS DESCRIPTION
1. Rotate Ironing Board
2. Collar Hanger
3. Water Tank
4. Telescopic Poles
5. Rotate Steam Nozzle
6. Body Base
7. Main Body
8. Fabric Boot Cap
9. Nozzle Hanger
PRODUCT SPECIFICATION
Water Tank Capacity 1.2L
Steam Output Time 60s
Input Voltage 220-240V~50/60Hz
Output Power 1920-2280W
FUNCTION FEATURES
Main Body Display Panel
Handle function buttons
According to your demand, press the rotate
button to adjust the nozzle 90° to the left.
Nozzle rotate button
On the top: Steaming Gear (with blue light on)
for continuous steam.
At bottom: Ironing Gear(with red light on). To
avoid damage to clothes caused by over time
ironing, if the switch is not turned on by user
for 15 minutes, this steamer will enter Standby
Mode automatically, with its indicator light
blinking, and steam stops working. Turn
on the Power ON/OFF switch again to let it
continue to work.
Sensor Switch on Main Body
When the steamer is working, steamer will
stop producing steam and continue to
heat-up when the Sensor Switch is pressed
down. If the Sensor Switch is pressed down,
with Standby Sleep Lamp on,for over 5
minute, buzzer will alarm once, buzzer will
alarm continually after 30 seconds and enter
Standby Mode. If the sensor switch is released
during this time, Standby Sleep Light goes o
and steamer resume to work.
Pressure release setting
When the pressure inside heater is
too high, the setting at the bottom
of main body would release
pressure automatically.
Auto pressure
release hole
Standby mode
PRODUCT INSTALLATION
STEP 1
Unlock both sides of the body base, insert the Telescopic Poles (the direction of
both poles needs to be accordant) into the base, and lock in place.
STEP 2
Adjust the telescopic poles to appropriate height, and lock in place.
STEP 3
Insert the collar hanger into the top of the ironing board.
STEP 4
Open the lock of the ironing board, install the board along the telescopic
poles, and lock in place.
STEP 5
Put the main body onto the base, then put the steamer nozzle onto
the recess above the main body.
STEP 6
Installation nished, product image as above.
INSTRUCTION FOR USE
STEP 1
Fill in the Water Tank and replace & tighten its cap.
STEP 2
Plug in, sound the main body beeps, then the power pilot lamp icker, and the
appliance switches to the stand by mode.
STEP 3
Touch the Power ON/OFF switch on Touching Screen on steamer, buzzer
will make a “bee”sound, steamer is turned on, and indicator light is on,
or is on(depends on the gear on Steam Nozzle Handle). Indicator light
blinks and steamer is ready to use after 48-second heat-up time, then
indicator light is on.
STEP 4
Steamer enters Working Mode after 48 seconds. Set the gear on Steam Nozzle
Handle upwards to enter Steaming Gear, with blue light on and on, steam will
spray out. Set the gear on Steam Nozzle Handle downwards to enter Ironing
Gear, with the red light on and on, no steam is produced.
STEP 5
Keep pressing on the red button behind the ironing board, so that you can
adjust the slope angle of the ironing board at random.
STEP 6
Ready for garment steaming.
MAINTENANCE AND CLEANING
STEP 1
Touch the Power ON/OFF switch on Touching Screen on steamer to turn o the
steamer, buzzer will make a “bee”sound, steamer is turned o, Indicator Light
blinks and steamer is under Standby Mode. Pull out the Plug and wait for at
least 30 minutes till the steamer cools down completely.
STEP 2
Take out the water tank and drug out the water. Adjust the telescopic poles to
appropriate place for easy storage.
DISASSEMBLY INSTRUCTION FOR IRONING CLOTH
STEP 1
Unlock the ironing board on both sides.And remove the ironing board with
both hands.
STEP 2
Remove the collar hanger and the decoration board.
STEP 3
Loosen the string behind the ironing board, then remove the ironing cloth.
STEP 4
Cover the ironing board with new ironing cloth and lace in place. Pull the
string upward and x it to the hook. Then install the decoration board back in
place, the ironing board is ready for use.
ACCESSORIES INSTRUCTION FOR USE
Rotate nozzle
mode changing-over
Recommended Recommended for
for horizontal ironing vertical or oblique ironing
Fabric Boot Cap Installation
Warm prompt: To prevent the fabric from being damaged by the high
temperature, please choose to use the boot cap in appropriate according to
how the temperature resistant of the fabric is.
Attention: When the appliance is still operating or the nozzle panel doesn't
drop to room temperature, please don't install or dismantle the boot cap so as
not to be scalded.
Nozzle Hanger Installation
Install the hanger to the middle of the telescopic poles, adjust it to appropriate
height and then lock in place.
To prevent fabric and ironing
board from being scalded, please
don't put the nozzle on the same
position for more than 30 seconds.
Use of Rotate Ironing Board
Attention: Be cautious of being hurt while adjusting the ironing board.
Separated base
Use of creel
TROUBLE SHOOTING
Problem Reason Solution
Unit fails to work.
Pilot lamp does not
illuminate
• The unit is not
plugged in
• House hold power
system problem /
fuse is blown
• Plug in the unit
• Call a qualied
electrician for help
Unit fails to steam Pilot
lamp illuminates
• Water Tank is empty
• Thermal cut-o is
damaged
• Thermostat is
damaged
• Switch on Handle
or Sensor Switch on
Main Body or Water
pump is damaged
• Rell the Water Tank
• Call a qualied
electrician for help.
• Call a qualied
electrician for help.
• Call a qualied
electrician for help
Nozzle panel heating
and works normally,
Pilot lamp does not
illuminates
Pilot lamp is broken Call a qualied
electrician for help
Less steam spraying out Voltage is too low Please avoid to use
this appliance during
the surge in electricity
demand
Nozzle has water
leakage problem
• It is normal that a
few of water sprayed
out from the nozzle
when turn it on.
• Heating pot does not
work
• This phenomenon
will distinguish after
one minute
• Call a qualied
electrician for help
Water tank leakage • Water tank's screw is
not tightened
• Water tank is broken
• Tighten the screw of
water tank
• Call a qualied
electrician for help
Appliance leakage Inside water tube is
broken
Call a qualied
electrician for help
Water tank is out of
shape
Fill the tank with hot
water
Call a qualied
electrician for help
ENVIRONMENT
This appliance should not be put into the domestic garbage at the end
of its durability, but must be oered at a central point for the recycling
of electric and electronic domestic appliances. This symbol on the appliance,
instruction manual and packaging puts your attention to this important issue.
The materials used in this appliance can be recycled. By recycling of used
domestic appliances you contribute an important push to the protection of
our environment. Ask your local authorities for information regarding the point
of recollection.
EN Instruction manual
service.princess.info
© Princess 2017
PARTS DESCRIPTION /
Garment steamer
EN Instruction manual
AR
1
4
5
7 8 9
3
6
2
To avoid being scalded, please don't rotate the
nozzle when the nozzle panel doesn't drop down to
the room temperature, nor during operation either.
Be cautious about the steam
spraying out from the hole when
the appliance is operating, so as
not to be scalded.
If the appliance enters
standby mode for less
than 3 minutes, reboot the
appliance, it will return to
work without pre-heating.
If the appliance enters
standby mode for more
than 3 minutes, reboot
the appliance, it needs to
pre-heat for 25 seconds to
return to work.
If the appliance enters
standby mode for more
than 5 minutes, reboot the
appliance, it needs to pre-
heat for 48 seconds to return
to work.
332850
- Children being supervised not to play with the appliance
- The iron must not be left unattended while it is connected
to the supply mains
- The plug must be removed from the socket-outlet before
filled with water (for
steam irons
and irons incorporating means for
spraying water)
- The iron must be used and rested on a flat, stable surface
- When placing the iron on its stand, ensure that the
surface on which the stand is
- The iron is not to be used if it has been dropped, if there are visible signs of
-Care should be taken when using the appliance due to the emission of steam
-If the supply cord is damaged, it must be replaced by manufacturer, its service
Agent or similarly qualified person to avoid hazard.
the water reservoir is
placed is stable
damage or if it is leaking
IMPORTANT SAFETY INSTRUCTIONS:
• Please use standard electricity service voltage (AC
220-240V,50/60Hz). Connecting to the incorrect voltage
may cause damage to the appliance and will invalidate the
warranty.
• Please don’t share the power supply with other high-
powered electric appliances.
• To avoid the electric shock, please don’t submerge the
appliance, plug or powercord in water or other liquids.
• Please don’t leave this appliance unattended while in
operation.
• Please ll the water tank to maximum before using and
observe the water level during use.
• Please don’t lay hose on the ground. Don’t wind hose. Don’t
operate the appliance if cord is damaged.
• Always keep the hose and nozzle elevated above the water
tank, so that the steam can be spouted conveniently. Never
insert any objects into any opening or hose.
• Please don’t cut or extend the steaming hose or power cord.
• Please don’t place the nozzle on any surface or appliance
power cord directly while it is hot or plugged in.
• Please be cautious about steam spraying out from the
nozzle. Do not direct nozzle at people or animals, in case the
steam exploding. Do not use the steamer on garments while
it is being worn.
• Please don’t lay or overturn the appliance when in use, or the
hot water will leakage.
• Turn o, unplug and allow the appliance to cool completely
for at least 30 minutes prior to draining the water tank and
water reservoir and storing.
• Always turn o and unplug unit before relling, draining,
cleaning or storing.
• For indoor use only.
• Please keep the appliance away from ammable materials
and chemicals.
• Please don’t ll the water tank with hot water or corrosive
cleaning agents which would cause damage. Distilled or
ltered water is strongly recommended.
• Only use Princess accessories on your Princess appliance. The
use of accessory attachments rather than those provided by
Princess may result in re, electric or irreversible damage to
the appliance.
• This appliance is not intended to be designed for children
and other persons whose physical, sensory or mental
capabilities is disabled or whom lack of sucient experience
or knowledge, please prevent them from using the appliance
without supervision or instruction by a person who can
ensure that they can use the appliance safely.
PARTS DESCRIPTION
1. Rotate Ironing Board
2. Collar Hanger
3. Water Tank
4. Telescopic Poles
5. Rotate Steam Nozzle
6. Body Base
7. Main Body
8. Fabric Boot Cap
9. Nozzle Hanger
PRODUCT SPECIFICATION
Water Tank Capacity 1.2L
Steam Output Time 60s
Input Voltage 220-240V~50/60Hz
Output Power 1920-2280W
FUNCTION FEATURES
Main Body Display Panel
Handle function buttons
According to your demand, press the rotate
button to adjust the nozzle 90° to the left.
Nozzle rotate button
On the top: Steaming Gear (with blue light on)
for continuous steam.
At bottom: Ironing Gear(with red light on). To
avoid damage to clothes caused by over time
ironing, if the switch is not turned on by user
for 15 minutes, this steamer will enter Standby
Mode automatically, with its indicator light
blinking, and steam stops working. Turn
on the Power ON/OFF switch again to let it
continue to work.
Sensor Switch on Main Body
When the steamer is working, steamer will
stop producing steam and continue to
heat-up when the Sensor Switch is pressed
down. If the Sensor Switch is pressed down,
with Standby Sleep Lamp on,for over 5
minute, buzzer will alarm once, buzzer will
alarm continually after 30 seconds and enter
Standby Mode. If the sensor switch is released
during this time, Standby Sleep Light goes o
and steamer resume to work.
Pressure release setting
When the pressure inside heater is
too high, the setting at the bottom
of main body would release
pressure automatically.
Auto pressure
release hole
Standby mode
PRODUCT INSTALLATION
STEP 1
Unlock both sides of the body base, insert the Telescopic Poles (the direction of
both poles needs to be accordant) into the base, and lock in place.
STEP 2
Adjust the telescopic poles to appropriate height, and lock in place.
STEP 3
Insert the collar hanger into the top of the ironing board.
STEP 4
Open the lock of the ironing board, install the board along the telescopic
poles, and lock in place.
STEP 5
Put the main body onto the base, then put the steamer nozzle onto
the recess above the main body.
STEP 6
Installation nished, product image as above.
INSTRUCTION FOR USE
STEP 1
Fill in the Water Tank and replace & tighten its cap.
STEP 2
Plug in, sound the main body beeps, then the power pilot lamp icker, and the
appliance switches to the stand by mode.
STEP 3
Touch the Power ON/OFF switch on Touching Screen on steamer, buzzer
will make a “bee” sound, steamer is turned on, and indicator light is on,
or is on(depends on the gear on Steam Nozzle Handle). Indicator light
blinks and steamer is ready to use after 48-second heat-up time, then
indicator light is on.
STEP 4
Steamer enters Working Mode after 48 seconds. Set the gear on Steam Nozzle
Handle upwards to enter Steaming Gear, with blue light on and on, steam will
spray out. Set the gear on Steam Nozzle Handle downwards to enter Ironing
Gear, with the red light on and on, no steam is produced.
STEP 5
Keep pressing on the red button behind the ironing board, so that you can
adjust the slope angle of the ironing board at random.
STEP 6
Ready for garment steaming.
MAINTENANCE AND CLEANING
STEP 1
Touch the Power ON/OFF switch on Touching Screen on steamer to turn o the
steamer, buzzer will make a “bee”sound, steamer is turned o, Indicator Light
blinks and steamer is under Standby Mode. Pull out the Plug and wait for at
least 30 minutes till the steamer cools down completely.
STEP 2
Take out the water tank and drug out the water. Adjust the telescopic poles to
appropriate place for easy storage.
DISASSEMBLY INSTRUCTION FOR IRONING CLOTH
STEP 1
Unlock the ironing board on both sides.And remove the ironing board with
both hands.
STEP 2
Remove the collar hanger and the decoration board.
STEP 3
Loosen the string behind the ironing board, then remove the ironing cloth.
STEP 4
Cover the ironing board with new ironing cloth and lace in place. Pull the
string upward and x it to the hook. Then install the decoration board back in
place, the ironing board is ready for use.
ACCESSORIES INSTRUCTION FOR USE
Rotate nozzle
mode changing-over
Recommended Recommended for
for horizontal ironing vertical or oblique ironing
Fabric Boot Cap Installation
Warm prompt: To prevent the fabric from being damaged by the high
temperature, please choose to use the boot cap in appropriate according to
how the temperature resistant of the fabric is.
Attention: When the appliance is still operating or the nozzle panel doesn't
drop to room temperature, please don't install or dismantle the boot cap so as
not to be scalded.
Nozzle Hanger Installation
Install the hanger to the middle of the telescopic poles, adjust it to appropriate
height and then lock in place.
To prevent fabric and ironing
board from being scalded, please
don't put the nozzle on the same
position for more than 30 seconds.
Use of Rotate Ironing Board
Attention: Be cautious of being hurt while adjusting the ironing board.
Separated base
Use of creel
TROUBLE SHOOTING
Problem Reason Solution
Unit fails to work.
Pilot lamp does not
illuminate
• The unit is not
plugged in
• House hold power
system problem /
fuse is blown
• Plug in the unit
• Call a qualied
electrician for help
Unit fails to steam Pilot
lamp illuminates
• Water Tank is empty
• Thermal cut-o is
damaged
• Thermostat is
damaged
• Switch on Handle
or Sensor Switch on
Main Body or Water
pump is damaged
• Rell the Water Tank
• Call a qualied
electrician for help.
• Call a qualied
electrician for help.
• Call a qualied
electrician for help
Nozzle panel heating
and works normally,
Pilot lamp does not
illuminates
Pilot lamp is broken Call a qualied
electrician for help
Less steam spraying out Voltage is too low Please avoid to use
this appliance during
the surge in electricity
demand
Nozzle has water
leakage problem
• It is normal that a
few of water sprayed
out from the nozzle
when turn it on.
• Heating pot does not
work
• This phenomenon
will distinguish after
one minute
• Call a qualied
electrician for help
Water tank leakage • Water tank's screw is
not tightened
• Water tank is broken
• Tighten the screw of
water tank
• Call a qualied
electrician for help
Appliance leakage Inside water tube is
broken
Call a qualied
electrician for help
Water tank is out of
shape
Fill the tank with hot
water
Call a qualied
electrician for help
ENVIRONMENT
This appliance should not be put into the domestic garbage at the end
of its durability, but must be oered at a central point for the recycling
of electric and electronic domestic appliances. This symbol on the appliance,
instruction manual and packaging puts your attention to this important issue.
The materials used in this appliance can be recycled. By recycling of used
domestic appliances you contribute an important push to the protection of
our environment. Ask your local authorities for information regarding the point
of recollection.
EN Instruction manual
service.princess.info
© Princess 2017
PARTS DESCRIPTION /
Garment steamer
EN Instruction manual
AR
1
4
5
7 8 9
3
6
2
To avoid being scalded, please don't rotate the
nozzle when the nozzle panel doesn't drop down to
the room temperature, nor during operation either.
Be cautious about the steam
spraying out from the hole when
the appliance is operating, so as
not to be scalded.
If the appliance enters
standby mode for less
than 3 minutes, reboot the
appliance, it will return to
work without pre-heating.
If the appliance enters
standby mode for more
than 3 minutes, reboot
the appliance, it needs to
pre-heat for 25 seconds to
return to work.
If the appliance enters
standby mode for more
than 5 minutes, reboot the
appliance, it needs to pre-
heat for 48 seconds to return
to work.
332850
- Children being supervised not to play with the appliance
- The iron must not be left unattended while it is connected
to the supply mains
- The plug must be removed from the socket-outlet before
filled with water (for
steam irons
and irons incorporating means for
spraying water)
- The iron must be used and rested on a flat, stable surface
- When placing the iron on its stand, ensure that the
surface on which the stand is
- The iron is not to be used if it has been dropped, if there are visible signs of
-Care should be taken when using the appliance due to the emission of steam
-If the supply cord is damaged, it must be replaced by manufacturer, its service
Agent or similarly qualified person to avoid hazard.
the water reservoir is
placed is stable
damage or if it is leaking
IMPORTANT SAFETY INSTRUCTIONS:
• Please use standard electricity service voltage (AC
220-240V,50/60Hz). Connecting to the incorrect voltage
may cause damage to the appliance and will invalidate the
warranty.
• Please don’t share the power supply with other high-
powered electric appliances.
• To avoid the electric shock, please don’t submerge the
appliance, plug or powercord in water or other liquids.
• Please don’t leave this appliance unattended while in
operation.
• Please ll the water tank to maximum before using and
observe the water level during use.
• Please don’t lay hose on the ground. Don’t wind hose. Don’t
operate the appliance if cord is damaged.
• Always keep the hose and nozzle elevated above the water
tank, so that the steam can be spouted conveniently. Never
insert any objects into any opening or hose.
• Please don’t cut or extend the steaming hose or power cord.
• Please don’t place the nozzle on any surface or appliance
power cord directly while it is hot or plugged in.
• Please be cautious about steam spraying out from the
nozzle. Do not direct nozzle at people or animals, in case the
steam exploding. Do not use the steamer on garments while
it is being worn.
• Please don’t lay or overturn the appliance when in use, or the
hot water will leakage.
• Turn o, unplug and allow the appliance to cool completely
for at least 30 minutes prior to draining the water tank and
water reservoir and storing.
• Always turn o and unplug unit before relling, draining,
cleaning or storing.
• For indoor use only.
• Please keep the appliance away from ammable materials
and chemicals.
• Please don’t ll the water tank with hot water or corrosive
cleaning agents which would cause damage. Distilled or
ltered water is strongly recommended.
• Only use Princess accessories on your Princess appliance. The
use of accessory attachments rather than those provided by
Princess may result in re, electric or irreversible damage to
the appliance.
• This appliance is not intended to be designed for children
and other persons whose physical, sensory or mental
capabilities is disabled or whom lack of sucient experience
or knowledge, please prevent them from using the appliance
without supervision or instruction by a person who can
ensure that they can use the appliance safely.
PARTS DESCRIPTION
1. Rotate Ironing Board
2. Collar Hanger
3. Water Tank
4. Telescopic Poles
5. Rotate Steam Nozzle
6. Body Base
7. Main Body
8. Fabric Boot Cap
9. Nozzle Hanger
PRODUCT SPECIFICATION
Water Tank Capacity 1.2L
Steam Output Time 60s
Input Voltage 220-240V~50/60Hz
Output Power 1920-2280W
FUNCTION FEATURES
Main Body Display Panel
Handle function buttons
According to your demand, press the rotate
button to adjust the nozzle 90° to the left.
Nozzle rotate button
On the top: Steaming Gear (with blue light on)
for continuous steam.
At bottom: Ironing Gear(with red light on). To
avoid damage to clothes caused by over time
ironing, if the switch is not turned on by user
for 15 minutes, this steamer will enter Standby
Mode automatically, with its indicator light
blinking, and steam stops working. Turn
on the Power ON/OFF switch again to let it
continue to work.
Sensor Switch on Main Body
When the steamer is working, steamer will
stop producing steam and continue to
heat-up when the Sensor Switch is pressed
down. If the Sensor Switch is pressed down,
with Standby Sleep Lamp on,for over 5
minute, buzzer will alarm once, buzzer will
alarm continually after 30 seconds and enter
Standby Mode. If the sensor switch is released
during this time, Standby Sleep Light goes o
and steamer resume to work.
Pressure release setting
When the pressure inside heater is
too high, the setting at the bottom
of main body would release
pressure automatically.
Auto pressure
release hole
Standby mode
PRODUCT INSTALLATION
STEP 1
Unlock both sides of the body base, insert the Telescopic Poles (the direction of
both poles needs to be accordant) into the base, and lock in place.
STEP 2
Adjust the telescopic poles to appropriate height, and lock in place.
STEP 3
Insert the collar hanger into the top of the ironing board.
STEP 4
Open the lock of the ironing board, install the board along the telescopic
poles, and lock in place.
STEP 5
Put the main body onto the base, then put the steamer nozzle onto
the recess above the main body.
STEP 6
Installation nished, product image as above.
INSTRUCTION FOR USE
STEP 1
Fill in the Water Tank and replace & tighten its cap.
STEP 2
Plug in, sound the main body beeps, then the power pilot lamp icker, and the
appliance switches to the stand by mode.
STEP 3
Touch the Power ON/OFF switch on Touching Screen on steamer, buzzer
will make a “bee” sound, steamer is turned on, and indicator light is on,
or is on(depends on the gear on Steam Nozzle Handle). Indicator light
blinks and steamer is ready to use after 48-second heat-up time, then
indicator light is on.
STEP 4
Steamer enters Working Mode after 48 seconds. Set the gear on Steam Nozzle
Handle upwards to enter Steaming Gear, with blue light on and on, steam will
spray out. Set the gear on Steam Nozzle Handle downwards to enter Ironing
Gear, with the red light on and on, no steam is produced.
STEP 5
Keep pressing on the red button behind the ironing board, so that you can
adjust the slope angle of the ironing board at random.
STEP 6
Ready for garment steaming.
MAINTENANCE AND CLEANING
STEP 1
Touch the Power ON/OFF switch on Touching Screen on steamer to turn o the
steamer, buzzer will make a “bee” sound, steamer is turned o, Indicator Light
blinks and steamer is under Standby Mode. Pull out the Plug and wait for at
least 30 minutes till the steamer cools down completely.
STEP 2
Take out the water tank and drug out the water. Adjust the telescopic poles to
appropriate place for easy storage.
DISASSEMBLY INSTRUCTION FOR IRONING CLOTH
STEP 1
Unlock the ironing board on both sides.And remove the ironing board with
both hands.
STEP 2
Remove the collar hanger and the decoration board.
STEP 3
Loosen the string behind the ironing board, then remove the ironing cloth.
STEP 4
Cover the ironing board with new ironing cloth and lace in place. Pull the
string upward and x it to the hook. Then install the decoration board back in
place, the ironing board is ready for use.
ACCESSORIES INSTRUCTION FOR USE
Rotate nozzle
mode changing-over
Recommended Recommended for
for horizontal ironing vertical or oblique ironing
Fabric Boot Cap Installation
Warm prompt: To prevent the fabric from being damaged by the high
temperature, please choose to use the boot cap in appropriate according to
how the temperature resistant of the fabric is.
Attention: When the appliance is still operating or the nozzle panel doesn't
drop to room temperature, please don't install or dismantle the boot cap so as
not to be scalded.
Nozzle Hanger Installation
Install the hanger to the middle of the telescopic poles, adjust it to appropriate
height and then lock in place.
To prevent fabric and ironing
board from being scalded, please
don't put the nozzle on the same
position for more than 30 seconds.
Use of Rotate Ironing Board
Attention: Be cautious of being hurt while adjusting the ironing board.
Separated base
Use of creel
TROUBLE SHOOTING
Problem Reason Solution
Unit fails to work.
Pilot lamp does not
illuminate
• The unit is not
plugged in
• House hold power
system problem /
fuse is blown
• Plug in the unit
• Call a qualied
electrician for help
Unit fails to steam Pilot
lamp illuminates
• Water Tank is empty
• Thermal cut-o is
damaged
• Thermostat is
damaged
• Switch on Handle
or Sensor Switch on
Main Body or Water
pump is damaged
• Rell the Water Tank
• Call a qualied
electrician for help.
• Call a qualied
electrician for help.
• Call a qualied
electrician for help
Nozzle panel heating
and works normally,
Pilot lamp does not
illuminates
Pilot lamp is broken Call a qualied
electrician for help
Less steam spraying out Voltage is too low Please avoid to use
this appliance during
the surge in electricity
demand
Nozzle has water
leakage problem
• It is normal that a
few of water sprayed
out from the nozzle
when turn it on.
• Heating pot does not
work
• This phenomenon
will distinguish after
one minute
• Call a qualied
electrician for help
Water tank leakage • Water tank's screw is
not tightened
• Water tank is broken
• Tighten the screw of
water tank
• Call a qualied
electrician for help
Appliance leakage Inside water tube is
broken
Call a qualied
electrician for help
Water tank is out of
shape
Fill the tank with hot
water
Call a qualied
electrician for help
ENVIRONMENT
This appliance should not be put into the domestic garbage at the end
of its durability, but must be oered at a central point for the recycling
of electric and electronic domestic appliances. This symbol on the appliance,
instruction manual and packaging puts your attention to this important issue.
The materials used in this appliance can be recycled. By recycling of used
domestic appliances you contribute an important push to the protection of
our environment. Ask your local authorities for information regarding the point
of recollection.
EN Instruction manual
service.princess.info
© Princess 2017
PARTS DESCRIPTION /
Garment steamer
EN Instruction manual
AR
1
4
5
7 8 9
3
6
2
To avoid being scalded, please don't rotate the
nozzle when the nozzle panel doesn't drop down to
the room temperature, nor during operation either.
Be cautious about the steam
spraying out from the hole when
the appliance is operating, so as
not to be scalded.
If the appliance enters
standby mode for less
than 3 minutes, reboot the
appliance, it will return to
work without pre-heating.
If the appliance enters
standby mode for more
than 3 minutes, reboot
the appliance, it needs to
pre-heat for 25 seconds to
return to work.
If the appliance enters
standby mode for more
than 5 minutes, reboot the
appliance, it needs to pre-
heat for 48 seconds to return
to work.
332850
- Children being supervised not to play with the appliance
- The iron must not be left unattended while it is connected
to the supply mains
- The plug must be removed from the socket-outlet before
filled with water (for
steam irons
and irons incorporating means for
spraying water)
- The iron must be used and rested on a flat, stable surface
- When placing the iron on its stand, ensure that the
surface on which the stand is
- The iron is not to be used if it has been dropped, if there are visible signs of
-Care should be taken when using the appliance due to the emission of steam
-If the supply cord is damaged, it must be replaced by manufacturer, its service
Agent or similarly qualified person to avoid hazard.
the water reservoir is
placed is stable
damage or if it is leaking
IMPORTANT SAFETY INSTRUCTIONS:
• Please use standard electricity service voltage (AC
220-240V,50/60Hz). Connecting to the incorrect voltage
may cause damage to the appliance and will invalidate the
warranty.
• Please don’t share the power supply with other high-
powered electric appliances.
• To avoid the electric shock, please don’t submerge the
appliance, plug or powercord in water or other liquids.
• Please don’t leave this appliance unattended while in
operation.
• Please ll the water tank to maximum before using and
observe the water level during use.
• Please don’t lay hose on the ground. Don’t wind hose. Don’t
operate the appliance if cord is damaged.
• Always keep the hose and nozzle elevated above the water
tank, so that the steam can be spouted conveniently. Never
insert any objects into any opening or hose.
• Please don’t cut or extend the steaming hose or power cord.
• Please don’t place the nozzle on any surface or appliance
power cord directly while it is hot or plugged in.
• Please be cautious about steam spraying out from the
nozzle. Do not direct nozzle at people or animals, in case the
steam exploding. Do not use the steamer on garments while
it is being worn.
• Please don’t lay or overturn the appliance when in use, or the
hot water will leakage.
• Turn o, unplug and allow the appliance to cool completely
for at least 30 minutes prior to draining the water tank and
water reservoir and storing.
• Always turn o and unplug unit before relling, draining,
cleaning or storing.
• For indoor use only.
• Please keep the appliance away from ammable materials
and chemicals.
• Please don’t ll the water tank with hot water or corrosive
cleaning agents which would cause damage. Distilled or
ltered water is strongly recommended.
• Only use Princess accessories on your Princess appliance. The
use of accessory attachments rather than those provided by
Princess may result in re, electric or irreversible damage to
the appliance.
• This appliance is not intended to be designed for children
and other persons whose physical, sensory or mental
capabilities is disabled or whom lack of sucient experience
or knowledge, please prevent them from using the appliance
without supervision or instruction by a person who can
ensure that they can use the appliance safely.
PARTS DESCRIPTION
1. Rotate Ironing Board
2. Collar Hanger
3. Water Tank
4. Telescopic Poles
5. Rotate Steam Nozzle
6. Body Base
7. Main Body
8. Fabric Boot Cap
9. Nozzle Hanger
PRODUCT SPECIFICATION
Water Tank Capacity 1.2L
Steam Output Time 60s
Input Voltage 220-240V~50/60Hz
Output Power 1920-2280W
FUNCTION FEATURES
Main Body Display Panel
Handle function buttons
According to your demand, press the rotate
button to adjust the nozzle 90° to the left.
Nozzle rotate button
On the top: Steaming Gear (with blue light on)
for continuous steam.
At bottom: Ironing Gear(with red light on). To
avoid damage to clothes caused by over time
ironing, if the switch is not turned on by user
for 15 minutes, this steamer will enter Standby
Mode automatically, with its indicator light
blinking, and steam stops working. Turn
on the Power ON/OFF switch again to let it
continue to work.
Sensor Switch on Main Body
When the steamer is working, steamer will
stop producing steam and continue to
heat-up when the Sensor Switch is pressed
down. If the Sensor Switch is pressed down,
with Standby Sleep Lamp on,for over 5
minute, buzzer will alarm once, buzzer will
alarm continually after 30 seconds and enter
Standby Mode. If the sensor switch is released
during this time, Standby Sleep Light goes o
and steamer resume to work.
Pressure release setting
When the pressure inside heater is
too high, the setting at the bottom
of main body would release
pressure automatically.
Auto pressure
release hole
Standby mode
PRODUCT INSTALLATION
STEP 1
Unlock both sides of the body base, insert the Telescopic Poles (the direction of
both poles needs to be accordant) into the base, and lock in place.
STEP 2
Adjust the telescopic poles to appropriate height, and lock in place.
STEP 3
Insert the collar hanger into the top of the ironing board.
STEP 4
Open the lock of the ironing board, install the board along the telescopic
poles, and lock in place.
STEP 5
Put the main body onto the base, then put the steamer nozzle onto
the recess above the main body.
STEP 6
Installation nished, product image as above.
INSTRUCTION FOR USE
STEP 1
Fill in the Water Tank and replace & tighten its cap.
STEP 2
Plug in, sound the main body beeps, then the power pilot lamp icker, and the
appliance switches to the stand by mode.
STEP 3
Touch the Power ON/OFF switch on Touching Screen on steamer, buzzer
will make a “bee” sound, steamer is turned on, and indicator light is on,
or is on(depends on the gear on Steam Nozzle Handle). Indicator light
blinks and steamer is ready to use after 48-second heat-up time, then
indicator light is on.
STEP 4
Steamer enters Working Mode after 48 seconds. Set the gear on Steam Nozzle
Handle upwards to enter Steaming Gear, with blue light on and on, steam will
spray out. Set the gear on Steam Nozzle Handle downwards to enter Ironing
Gear, with the red light on and on, no steam is produced.
STEP 5
Keep pressing on the red button behind the ironing board, so that you can
adjust the slope angle of the ironing board at random.
STEP 6
Ready for garment steaming.
MAINTENANCE AND CLEANING
STEP 1
Touch the Power ON/OFF switch on Touching Screen on steamer to turn o the
steamer, buzzer will make a “bee”sound, steamer is turned o, Indicator Light
blinks and steamer is under Standby Mode. Pull out the Plug and wait for at
least 30 minutes till the steamer cools down completely.
STEP 2
Take out the water tank and drug out the water. Adjust the telescopic poles to
appropriate place for easy storage.
DISASSEMBLY INSTRUCTION FOR IRONING CLOTH
STEP 1
Unlock the ironing board on both sides.And remove the ironing board with
both hands.
STEP 2
Remove the collar hanger and the decoration board.
STEP 3
Loosen the string behind the ironing board, then remove the ironing cloth.
STEP 4
Cover the ironing board with new ironing cloth and lace in place. Pull the
string upward and x it to the hook. Then install the decoration board back in
place, the ironing board is ready for use.
ACCESSORIES INSTRUCTION FOR USE
Rotate nozzle
mode changing-over
Recommended Recommended for
for horizontal ironing vertical or oblique ironing
Fabric Boot Cap Installation
Warm prompt: To prevent the fabric from being damaged by the high
temperature, please choose to use the boot cap in appropriate according to
how the temperature resistant of the fabric is.
Attention: When the appliance is still operating or the nozzle panel doesn't
drop to room temperature, please don't install or dismantle the boot cap so as
not to be scalded.
Nozzle Hanger Installation
Install the hanger to the middle of the telescopic poles, adjust it to appropriate
height and then lock in place.
To prevent fabric and ironing
board from being scalded, please
don't put the nozzle on the same
position for more than 30 seconds.
Use of Rotate Ironing Board
Attention: Be cautious of being hurt while adjusting the ironing board.
Separated base
Use of creel
TROUBLE SHOOTING
Problem Reason Solution
Unit fails to work.
Pilot lamp does not
illuminate
• The unit is not
plugged in
• House hold power
system problem /
fuse is blown
• Plug in the unit
• Call a qualied
electrician for help
Unit fails to steam Pilot
lamp illuminates
• Water Tank is empty
• Thermal cut-o is
damaged
• Thermostat is
damaged
• Switch on Handle
or Sensor Switch on
Main Body or Water
pump is damaged
• Rell the Water Tank
• Call a qualied
electrician for help.
• Call a qualied
electrician for help.
• Call a qualied
electrician for help
Nozzle panel heating
and works normally,
Pilot lamp does not
illuminates
Pilot lamp is broken Call a qualied
electrician for help
Less steam spraying out Voltage is too low Please avoid to use
this appliance during
the surge in electricity
demand
Nozzle has water
leakage problem
• It is normal that a
few of water sprayed
out from the nozzle
when turn it on.
• Heating pot does not
work
• This phenomenon
will distinguish after
one minute
• Call a qualied
electrician for help
Water tank leakage • Water tank's screw is
not tightened
• Water tank is broken
• Tighten the screw of
water tank
• Call a qualied
electrician for help
Appliance leakage Inside water tube is
broken
Call a qualied
electrician for help
Water tank is out of
shape
Fill the tank with hot
water
Call a qualied
electrician for help
ENVIRONMENT
This appliance should not be put into the domestic garbage at the end
of its durability, but must be oered at a central point for the recycling
of electric and electronic domestic appliances. This symbol on the appliance,
instruction manual and packaging puts your attention to this important issue.
The materials used in this appliance can be recycled. By recycling of used
domestic appliances you contribute an important push to the protection of
our environment. Ask your local authorities for information regarding the point
of recollection.
EN Instruction manual
service.princess.info
© Princess 2017
PARTS DESCRIPTION /
Garment steamer
EN Instruction manual
AR
1
4
5
7 8 9
3
6
2
To avoid being scalded, please don't rotate the
nozzle when the nozzle panel doesn't drop down to
the room temperature, nor during operation either.
Be cautious about the steam
spraying out from the hole when
the appliance is operating, so as
not to be scalded.
If the appliance enters
standby mode for less
than 3 minutes, reboot the
appliance, it will return to
work without pre-heating.
If the appliance enters
standby mode for more
than 3 minutes, reboot
the appliance, it needs to
pre-heat for 25 seconds to
return to work.
If the appliance enters
standby mode for more
than 5 minutes, reboot the
appliance, it needs to pre-
heat for 48 seconds to return
to work.
332850
- Children being supervised not to play with the appliance
- The iron must not be left unattended while it is connected
to the supply mains
- The plug must be removed from the socket-outlet before
filled with water (for
steam irons
and irons incorporating means for
spraying water)
- The iron must be used and rested on a flat, stable surface
- When placing the iron on its stand, ensure that the
surface on which the stand is
- The iron is not to be used if it has been dropped, if there are visible signs of
-Care should be taken when using the appliance due to the emission of steam
-If the supply cord is damaged, it must be replaced by manufacturer, its service
Agent or similarly qualified person to avoid hazard.
the water reservoir is
placed is stable
damage or if it is leaking
IMPORTANT SAFETY INSTRUCTIONS:
• Please use standard electricity service voltage (AC
220-240V,50/60Hz). Connecting to the incorrect voltage
may cause damage to the appliance and will invalidate the
warranty.
• Please don’t share the power supply with other high-
powered electric appliances.
• To avoid the electric shock, please don’t submerge the
appliance, plug or powercord in water or other liquids.
• Please don’t leave this appliance unattended while in
operation.
• Please ll the water tank to maximum before using and
observe the water level during use.
• Please don’t lay hose on the ground. Don’t wind hose. Don’t
operate the appliance if cord is damaged.
• Always keep the hose and nozzle elevated above the water
tank, so that the steam can be spouted conveniently. Never
insert any objects into any opening or hose.
• Please don’t cut or extend the steaming hose or power cord.
• Please don’t place the nozzle on any surface or appliance
power cord directly while it is hot or plugged in.
• Please be cautious about steam spraying out from the
nozzle. Do not direct nozzle at people or animals, in case the
steam exploding. Do not use the steamer on garments while
it is being worn.
• Please don’t lay or overturn the appliance when in use, or the
hot water will leakage.
• Turn o, unplug and allow the appliance to cool completely
for at least 30 minutes prior to draining the water tank and
water reservoir and storing.
• Always turn o and unplug unit before relling, draining,
cleaning or storing.
• For indoor use only.
• Please keep the appliance away from ammable materials
and chemicals.
• Please don’t ll the water tank with hot water or corrosive
cleaning agents which would cause damage. Distilled or
ltered water is strongly recommended.
• Only use Princess accessories on your Princess appliance. The
use of accessory attachments rather than those provided by
Princess may result in re, electric or irreversible damage to
the appliance.
• This appliance is not intended to be designed for children
and other persons whose physical, sensory or mental
capabilities is disabled or whom lack of sucient experience
or knowledge, please prevent them from using the appliance
without supervision or instruction by a person who can
ensure that they can use the appliance safely.
PARTS DESCRIPTION
1. Rotate Ironing Board
2. Collar Hanger
3. Water Tank
4. Telescopic Poles
5. Rotate Steam Nozzle
6. Body Base
7. Main Body
8. Fabric Boot Cap
9. Nozzle Hanger
PRODUCT SPECIFICATION
Water Tank Capacity 1.2L
Steam Output Time 60s
Input Voltage 220-240V~50/60Hz
Output Power 1920-2280W
FUNCTION FEATURES
Main Body Display Panel
Handle function buttons
According to your demand, press the rotate
button to adjust the nozzle 90° to the left.
Nozzle rotate button
On the top: Steaming Gear (with blue light on)
for continuous steam.
At bottom: Ironing Gear(with red light on). To
avoid damage to clothes caused by over time
ironing, if the switch is not turned on by user
for 15 minutes, this steamer will enter Standby
Mode automatically, with its indicator light
blinking, and steam stops working. Turn
on the Power ON/OFF switch again to let it
continue to work.
Sensor Switch on Main Body
When the steamer is working, steamer will
stop producing steam and continue to
heat-up when the Sensor Switch is pressed
down. If the Sensor Switch is pressed down,
with Standby Sleep Lamp on,for over 5
minute, buzzer will alarm once, buzzer will
alarm continually after 30 seconds and enter
Standby Mode. If the sensor switch is released
during this time, Standby Sleep Light goes o
and steamer resume to work.
Pressure release setting
When the pressure inside heater is
too high, the setting at the bottom
of main body would release
pressure automatically.
Auto pressure
release hole
Standby mode
PRODUCT INSTALLATION
STEP 1
Unlock both sides of the body base, insert the Telescopic Poles (the direction of
both poles needs to be accordant) into the base, and lock in place.
STEP 2
Adjust the telescopic poles to appropriate height, and lock in place.
STEP 3
Insert the collar hanger into the top of the ironing board.
STEP 4
Open the lock of the ironing board, install the board along the telescopic
poles, and lock in place.
STEP 5
Put the main body onto the base, then put the steamer nozzle onto
the recess above the main body.
STEP 6
Installation nished, product image as above.
INSTRUCTION FOR USE
STEP 1
Fill in the Water Tank and replace & tighten its cap.
STEP 2
Plug in, sound the main body beeps, then the power pilot lamp icker, and the
appliance switches to the stand by mode.
STEP 3
Touch the Power ON/OFF switch on Touching Screen on steamer, buzzer
will make a “bee” sound, steamer is turned on, and indicator light is on,
or is on(depends on the gear on Steam Nozzle Handle). Indicator light
blinks and steamer is ready to use after 48-second heat-up time, then
indicator light is on.
STEP 4
Steamer enters Working Mode after 48 seconds. Set the gear on Steam Nozzle
Handle upwards to enter Steaming Gear, with blue light on and on, steam will
spray out. Set the gear on Steam Nozzle Handle downwards to enter Ironing
Gear, with the red light on and on, no steam is produced.
STEP 5
Keep pressing on the red button behind the ironing board, so that you can
adjust the slope angle of the ironing board at random.
STEP 6
Ready for garment steaming.
MAINTENANCE AND CLEANING
STEP 1
Touch the Power ON/OFF switch on Touching Screen on steamer to turn o the
steamer, buzzer will make a “bee” sound, steamer is turned o, Indicator Light
blinks and steamer is under Standby Mode. Pull out the Plug and wait for at
least 30 minutes till the steamer cools down completely.
STEP 2
Take out the water tank and drug out the water. Adjust the telescopic poles to
appropriate place for easy storage.
DISASSEMBLY INSTRUCTION FOR IRONING CLOTH
STEP 1
Unlock the ironing board on both sides.And remove the ironing board with
both hands.
STEP 2
Remove the collar hanger and the decoration board.
STEP 3
Loosen the string behind the ironing board, then remove the ironing cloth.
STEP 4
Cover the ironing board with new ironing cloth and lace in place. Pull the
string upward and x it to the hook. Then install the decoration board back in
place, the ironing board is ready for use.
ACCESSORIES INSTRUCTION FOR USE
Rotate nozzle
mode changing-over
Recommended Recommended for
for horizontal ironing vertical or oblique ironing
Fabric Boot Cap Installation
Warm prompt: To prevent the fabric from being damaged by the high
temperature, please choose to use the boot cap in appropriate according to
how the temperature resistant of the fabric is.
Attention: When the appliance is still operating or the nozzle panel doesn't
drop to room temperature, please don't install or dismantle the boot cap so as
not to be scalded.
Nozzle Hanger Installation
Install the hanger to the middle of the telescopic poles, adjust it to appropriate
height and then lock in place.
To prevent fabric and ironing
board from being scalded, please
don't put the nozzle on the same
position for more than 30 seconds.
Use of Rotate Ironing Board
Attention: Be cautious of being hurt while adjusting the ironing board.
Separated base
Use of creel
TROUBLE SHOOTING
Problem Reason Solution
Unit fails to work.
Pilot lamp does not
illuminate
• The unit is not
plugged in
• House hold power
system problem /
fuse is blown
• Plug in the unit
• Call a qualied
electrician for help
Unit fails to steam Pilot
lamp illuminates
• Water Tank is empty
• Thermal cut-o is
damaged
• Thermostat is
damaged
• Switch on Handle
or Sensor Switch on
Main Body or Water
pump is damaged
• Rell the Water Tank
• Call a qualied
electrician for help.
• Call a qualied
electrician for help.
• Call a qualied
electrician for help
Nozzle panel heating
and works normally,
Pilot lamp does not
illuminates
Pilot lamp is broken Call a qualied
electrician for help
Less steam spraying out Voltage is too low Please avoid to use
this appliance during
the surge in electricity
demand
Nozzle has water
leakage problem
• It is normal that a
few of water sprayed
out from the nozzle
when turn it on.
• Heating pot does not
work
• This phenomenon
will distinguish after
one minute
• Call a qualied
electrician for help
Water tank leakage • Water tank's screw is
not tightened
• Water tank is broken
• Tighten the screw of
water tank
• Call a qualied
electrician for help
Appliance leakage Inside water tube is
broken
Call a qualied
electrician for help
Water tank is out of
shape
Fill the tank with hot
water
Call a qualied
electrician for help
ENVIRONMENT
This appliance should not be put into the domestic garbage at the end
of its durability, but must be oered at a central point for the recycling
of electric and electronic domestic appliances. This symbol on the appliance,
instruction manual and packaging puts your attention to this important issue.
The materials used in this appliance can be recycled. By recycling of used
domestic appliances you contribute an important push to the protection of
our environment. Ask your local authorities for information regarding the point
of recollection.
EN Instruction manual
service.princess.info
© Princess 2017
PARTS DESCRIPTION /
Garment steamer
EN Instruction manual
AR
1
4
5
7 8 9
3
6
2
To avoid being scalded, please don't rotate the
nozzle when the nozzle panel doesn't drop down to
the room temperature, nor during operation either.
Be cautious about the steam
spraying out from the hole when
the appliance is operating, so as
not to be scalded.
If the appliance enters
standby mode for less
than 3 minutes, reboot the
appliance, it will return to
work without pre-heating.
If the appliance enters
standby mode for more
than 3 minutes, reboot
the appliance, it needs to
pre-heat for 25 seconds to
return to work.
If the appliance enters
standby mode for more
than 5 minutes, reboot the
appliance, it needs to pre-
heat for 48 seconds to return
to work.
332850
- Children being supervised not to play with the appliance
- The iron must not be left unattended while it is connected
to the supply mains
- The plug must be removed from the socket-outlet before
filled with water (for
steam irons
and irons incorporating means for
spraying water)
- The iron must be used and rested on a flat, stable surface
- When placing the iron on its stand, ensure that the
surface on which the stand is
- The iron is not to be used if it has been dropped, if there are visible signs of
-Care should be taken when using the appliance due to the emission of steam
-If the supply cord is damaged, it must be replaced by manufacturer, its service
Agent or similarly qualified person to avoid hazard.
the water reservoir is
placed is stable
damage or if it is leaking
IMPORTANT SAFETY INSTRUCTIONS:
• Please use standard electricity service voltage (AC
220-240V,50/60Hz). Connecting to the incorrect voltage
may cause damage to the appliance and will invalidate the
warranty.
• Please don’t share the power supply with other high-
powered electric appliances.
• To avoid the electric shock, please don’t submerge the
appliance, plug or powercord in water or other liquids.
• Please don’t leave this appliance unattended while in
operation.
• Please ll the water tank to maximum before using and
observe the water level during use.
• Please don’t lay hose on the ground. Don’t wind hose. Don’t
operate the appliance if cord is damaged.
• Always keep the hose and nozzle elevated above the water
tank, so that the steam can be spouted conveniently. Never
insert any objects into any opening or hose.
• Please don’t cut or extend the steaming hose or power cord.
• Please don’t place the nozzle on any surface or appliance
power cord directly while it is hot or plugged in.
• Please be cautious about steam spraying out from the
nozzle. Do not direct nozzle at people or animals, in case the
steam exploding. Do not use the steamer on garments while
it is being worn.
• Please don’t lay or overturn the appliance when in use, or the
hot water will leakage.
• Turn o, unplug and allow the appliance to cool completely
for at least 30 minutes prior to draining the water tank and
water reservoir and storing.
• Always turn o and unplug unit before relling, draining,
cleaning or storing.
• For indoor use only.
• Please keep the appliance away from ammable materials
and chemicals.
• Please don’t ll the water tank with hot water or corrosive
cleaning agents which would cause damage. Distilled or
ltered water is strongly recommended.
• Only use Princess accessories on your Princess appliance. The
use of accessory attachments rather than those provided by
Princess may result in re, electric or irreversible damage to
the appliance.
• This appliance is not intended to be designed for children
and other persons whose physical, sensory or mental
capabilities is disabled or whom lack of sucient experience
or knowledge, please prevent them from using the appliance
without supervision or instruction by a person who can
ensure that they can use the appliance safely.
PARTS DESCRIPTION
1. Rotate Ironing Board
2. Collar Hanger
3. Water Tank
4. Telescopic Poles
5. Rotate Steam Nozzle
6. Body Base
7. Main Body
8. Fabric Boot Cap
9. Nozzle Hanger
PRODUCT SPECIFICATION
Water Tank Capacity 1.2L
Steam Output Time 60s
Input Voltage 220-240V~50/60Hz
Output Power 1920-2280W
FUNCTION FEATURES
Main Body Display Panel
Handle function buttons
According to your demand, press the rotate
button to adjust the nozzle 90° to the left.
Nozzle rotate button
On the top: Steaming Gear (with blue light on)
for continuous steam.
At bottom: Ironing Gear(with red light on). To
avoid damage to clothes caused by over time
ironing, if the switch is not turned on by user
for 15 minutes, this steamer will enter Standby
Mode automatically, with its indicator light
blinking, and steam stops working. Turn
on the Power ON/OFF switch again to let it
continue to work.
Sensor Switch on Main Body
When the steamer is working, steamer will
stop producing steam and continue to
heat-up when the Sensor Switch is pressed
down. If the Sensor Switch is pressed down,
with Standby Sleep Lamp on,for over 5
minute, buzzer will alarm once, buzzer will
alarm continually after 30 seconds and enter
Standby Mode. If the sensor switch is released
during this time, Standby Sleep Light goes o
and steamer resume to work.
Pressure release setting
When the pressure inside heater is
too high, the setting at the bottom
of main body would release
pressure automatically.
Auto pressure
release hole
Standby mode
PRODUCT INSTALLATION
STEP 1
Unlock both sides of the body base, insert the Telescopic Poles (the direction of
both poles needs to be accordant) into the base, and lock in place.
STEP 2
Adjust the telescopic poles to appropriate height, and lock in place.
STEP 3
Insert the collar hanger into the top of the ironing board.
STEP 4
Open the lock of the ironing board, install the board along the telescopic
poles, and lock in place.
STEP 5
Put the main body onto the base, then put the steamer nozzle onto
the recess above the main body.
STEP 6
Installation nished, product image as above.
INSTRUCTION FOR USE
STEP 1
Fill in the Water Tank and replace & tighten its cap.
STEP 2
Plug in, sound the main body beeps, then the power pilot lamp icker, and the
appliance switches to the stand by mode.
STEP 3
Touch the Power ON/OFF switch on Touching Screen on steamer, buzzer
will make a “bee” sound, steamer is turned on, and indicator light is on,
or is on(depends on the gear on Steam Nozzle Handle). Indicator light
blinks and steamer is ready to use after 48-second heat-up time, then
indicator light is on.
STEP 4
Steamer enters Working Mode after 48 seconds. Set the gear on Steam Nozzle
Handle upwards to enter Steaming Gear, with blue light on and on, steam will
spray out. Set the gear on Steam Nozzle Handle downwards to enter Ironing
Gear, with the red light on and on, no steam is produced.
STEP 5
Keep pressing on the red button behind the ironing board, so that you can
adjust the slope angle of the ironing board at random.
STEP 6
Ready for garment steaming.
MAINTENANCE AND CLEANING
STEP 1
Touch the Power ON/OFF switch on Touching Screen on steamer to turn o the
steamer, buzzer will make a “bee” sound, steamer is turned o, Indicator Light
blinks and steamer is under Standby Mode. Pull out the Plug and wait for at
least 30 minutes till the steamer cools down completely.
STEP 2
Take out the water tank and drug out the water. Adjust the telescopic poles to
appropriate place for easy storage.
DISASSEMBLY INSTRUCTION FOR IRONING CLOTH
STEP 1
Unlock the ironing board on both sides.And remove the ironing board with
both hands.
STEP 2
Remove the collar hanger and the decoration board.
STEP 3
Loosen the string behind the ironing board, then remove the ironing cloth.
STEP 4
Cover the ironing board with new ironing cloth and lace in place. Pull the
string upward and x it to the hook. Then install the decoration board back in
place, the ironing board is ready for use.
ACCESSORIES INSTRUCTION FOR USE
Rotate nozzle
mode changing-over
Recommended Recommended for
for horizontal ironing vertical or oblique ironing
Fabric Boot Cap Installation
Warm prompt: To prevent the fabric from being damaged by the high
temperature, please choose to use the boot cap in appropriate according to
how the temperature resistant of the fabric is.
Attention: When the appliance is still operating or the nozzle panel doesn't
drop to room temperature, please don't install or dismantle the boot cap so as
not to be scalded.
Nozzle Hanger Installation
Install the hanger to the middle of the telescopic poles, adjust it to appropriate
height and then lock in place.
To prevent fabric and ironing
board from being scalded, please
don't put the nozzle on the same
position for more than 30 seconds.
Use of Rotate Ironing Board
Attention: Be cautious of being hurt while adjusting the ironing board.
Separated base
Use of creel
TROUBLE SHOOTING
Problem Reason Solution
Unit fails to work.
Pilot lamp does not
illuminate
• The unit is not
plugged in
• House hold power
system problem /
fuse is blown
• Plug in the unit
• Call a qualied
electrician for help
Unit fails to steam Pilot
lamp illuminates
• Water Tank is empty
• Thermal cut-o is
damaged
• Thermostat is
damaged
• Switch on Handle
or Sensor Switch on
Main Body or Water
pump is damaged
• Rell the Water Tank
• Call a qualied
electrician for help.
• Call a qualied
electrician for help.
• Call a qualied
electrician for help
Nozzle panel heating
and works normally,
Pilot lamp does not
illuminates
Pilot lamp is broken Call a qualied
electrician for help
Less steam spraying out Voltage is too low Please avoid to use
this appliance during
the surge in electricity
demand
Nozzle has water
leakage problem
• It is normal that a
few of water sprayed
out from the nozzle
when turn it on.
• Heating pot does not
work
• This phenomenon
will distinguish after
one minute
• Call a qualied
electrician for help
Water tank leakage • Water tank's screw is
not tightened
• Water tank is broken
• Tighten the screw of
water tank
• Call a qualied
electrician for help
Appliance leakage Inside water tube is
broken
Call a qualied
electrician for help
Water tank is out of
shape
Fill the tank with hot
water
Call a qualied
electrician for help
ENVIRONMENT
This appliance should not be put into the domestic garbage at the end
of its durability, but must be oered at a central point for the recycling
of electric and electronic domestic appliances. This symbol on the appliance,
instruction manual and packaging puts your attention to this important issue.
The materials used in this appliance can be recycled. By recycling of used
domestic appliances you contribute an important push to the protection of
our environment. Ask your local authorities for information regarding the point
of recollection.
EN Instruction manual
service.princess.info
© Princess 2017
PARTS DESCRIPTION /
Garment steamer
EN Instruction manual
AR
1
4
5
7 8 9
3
6
2
To avoid being scalded, please don't rotate the
nozzle when the nozzle panel doesn't drop down to
the room temperature, nor during operation either.
Be cautious about the steam
spraying out from the hole when
the appliance is operating, so as
not to be scalded.
If the appliance enters
standby mode for less
than 3 minutes, reboot the
appliance, it will return to
work without pre-heating.
If the appliance enters
standby mode for more
than 3 minutes, reboot
the appliance, it needs to
pre-heat for 25 seconds to
return to work.
If the appliance enters
standby mode for more
than 5 minutes, reboot the
appliance, it needs to pre-
heat for 48 seconds to return
to work.
332850
- Children being supervised not to play with the appliance
- The iron must not be left unattended while it is connected
to the supply mains
- The plug must be removed from the socket-outlet before
filled with water (for
steam irons
and irons incorporating means for
spraying water)
- The iron must be used and rested on a flat, stable surface
- When placing the iron on its stand, ensure that the
surface on which the stand is
- The iron is not to be used if it has been dropped, if there are visible signs of
-Care should be taken when using the appliance due to the emission of steam
-If the supply cord is damaged, it must be replaced by manufacturer, its service
Agent or similarly qualified person to avoid hazard.
the water reservoir is
placed is stable
damage or if it is leaking
Table of contents
Other Princess Steam Cleaner manuals
