Pro-Elec PEL00589 User manual

1
Model No. PEL00589
MAINTAINED
LED SQUARE EMERGENCY CEILING LIGHT

2
Please read these instructions carefully before starting installation and retain for
future reference. The centre page test record can be removed and kept with the
building re safety records.
IMPORTANT SAFETY INFORMATION
NOTE: Before drilling any holes, check that there are no hidden obstructions behind the
mounting surface such as pipes or cables.
1. Loosen the 4 screws on each side of the diffuser and remove it.
2. Remove the 2 screws holding the main assembly plate into the main casing and
allow the plate to swing clear on it’s pivot.
NOTE: the plate assembly can with care, be removed from it’s hinge in the casing,
to aid initial installation of the product to the mounting surface.
3. Create a wiring access hole centrally in the base of the casing where marked.
4. Drill holes through the moulded mounting position indicators as required.
5. Using the casing of the product as a template, mark the position of the xing holes
on your mounting surface.
6. Drill the xing holes and t wall plugs as appropriate.
7. Feed the mains supply wiring through the central hole and secure the casing to the
mounting surface using suitable xings (not supplied).
8. Ret the plate assembly to it’s hinge (if previously removed) and make connection
to the mains supply using the screw terminal block attached to the plate. Ensure
that the correct polarities are observed i.e.:
● Brown – Live terminal ‘L’
● Blue – Neutral terminal ‘N’.
● Green/Yellow – Earth terminal ‘E’
● Link wire ‘L’ to ‘SW’ can be removed to change between maintained and non-
maintained.
9. Write the current date on the battery pack.
10. Connect the battery pack terminal connector to the in-line connector on the wiring
to the emergency module.
INSTALLATION
RISK OF ELECTRICAL SHOCK. ALWAYS ISOLATE THE POWER AT THE MAINS
BEFORE INSTALLING OR MAINTAINING THIS EMERGENCY LIGHT.
• This product must be installed by a competent person in accordance with the
Building Regulations and the current edition of the IET Wiring Regulations
(BS7671).
• This product is suitable for mounting on normally ammable surfaces such as
wood, plasterboard or masonry.
• Emergency light ttings should have their own separate mains circuit, protected
with an appropriate MCB or fuse. They should not share their supply with other
lighting or electrical equipment.
• This product is suitable for connection to a 220-240V~ 50Hz, xed wiring supply.
• This product must be earthed.
• For indoor use only.
• Ensure that after installation the equipment remains accessible for regular
maintenance and testing.

3
Test Record Sheet on reverse
PULL OUT

4
Installation, maintenance and operation check record
Location:
Installation date: Installation test duration:
Installed by:
20__ 20__ 20__ 20__ 20__
Month Test Sign Date Sign Date Sign Date Sign Date Sign Date
1Short
2Short
3Short
4Short
5Short
6 1 h
7Short
8Short
9Short
10 Short
11 Short
12 3h

5
Installation, maintenance and operation check record
Location:
Installation date: Installation test duration:
Installed by:
20__ 20__ 20__ 20__ 20__
Month Test Sign Date Sign Date Sign Date Sign Date Sign Date
1Short
2Short
3Short
4Short
5Short
6 1 h
7Short
8Short
9Short
10 Short
11 Short
12 3h

6
Test Record Sheet on reverse
PULL OUT

7
11. Pivot the plate assembly ush into the casing and x into position with the 2 screws.
Make sure the screws are tightened.
12. Fit the diffuser into position and tighten the 4 screws.
13. Restore the power supply. The green LED should light to show the battery is being
charged.
14. In maintained mode the lamp will illuminate.
15. Perform the electrical tests specied in the Wiring Regulations (BS7671).
Main LED Plate
Assembly locating screws
Battery Connector
Mains connector
and fuses
Maintained
mode link wire
Battery
Battery charge LED
Note: This equipment must be checked regularly in compliance with local regulation and
codes of practice. For your own safety, testing should occur during the day.
• After installation, you should allow 24 hours for the battery pack to charge
fully before testing. Isolate the power supply and check that the lamp remains
illuminated for at least three hours. Restore the power supply.
• Each day: Check that the green charging LED is lit.
• Each month (short test): Isolate the power supply and check that the lamp remains
illuminated. Record the results on the test record sheet included with these
instructions.
• Every six months: Isolate the power supply and check that the lamp remains
illuminated after 1 hour. Record the results on the included test record.
• Once each year: Isolate the power supply and check that the lamp is still illuminated
after 3 hours. Record the results on the included test record.
Please keep these test records in a safe place. A re ofcer or other authorised
person may want to see your record of inspection and testing.
CLEANING AND MAINTENANCE
• Clean the product with a soft, dry cloth only. Do not use any solvents or abrasive
chemical cleaners.
• The LED lamps in this product are non-replaceable.
OPERATIONAL CHECKS

8
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF
ELECTRICAL & ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical
& Electronic Equipment (WEEE). Any WEEE marked products must not be mixed with
general household waste, but kept separate for the treatment, recovery and recycling
of the materials used. Waste batteries can be returned to any waste battery recycling
point which are provided by most battery retailers. Contact your local authority for
details of battery and recycling schemes in your area.
Made in China. PR2 9PP
Man Rev 1.0
Cd
Changing a fuse
• Two fuses are tted to this product and are located on the mains connection
terminal block and can be changed as follows:
1. Isolate from the mains supply.
2. Remove the diffuser and release the main LED plate assembly.
3. Pull the fuse holder out of the terminal block
4. Press the fuse out of the holder and replace with an identical fuse (240V F3A).
5. Insert the fuse holder back into the terminal block.
6. Ret the LED plate assembly. Tighten the screws and ret the diffuser.
7. Restore the mains power and check the operation.
SPECIFICATIONS
Input voltage: 220-240V~, 50Hz
Rated power: 16W
Lamps: SMD2835 LEDs x 60pcs
Luminous ux: 980Lm(AC) / 200Lm(DC)
Continuous emergency illumination: > 3 hours (when the battery is fully charged)
Battery pack: Ni-Cd, 6V, 2Ah
Recharge time: 24 hours – approx.
Ambient temperature: 0 - 40°C
Over-discharge protection: Yes
Ingress protection rating: IP65
Changing the battery
• If after a routine operation check, the lamp does not remain lit for the 3 hour period,
a new battery pack may be required. Change the battery pack as follows:
1. Isolate from the mains supply.
2. Remove the diffuser and release the main LED plate assembly.
3. Unplug the battery pack in line connector.
4. Loosen the battery locating nuts and remove the old battery pack.
5. Write the current date on the new battery pack.
6. Fit the new battery pack and secure in position.
7. Reconnect the battery pack in-line connector.
8. Ret the LED plate assembly. Tighten the screws and ret the diffuser.
9. Restore mains power and allow to charge for 24 hours.
10. Perform the full operation check and update the test record.