Pro-Form Activator V7 User manual

-lr| TM
Model No. 83t.14787.0
Serial No.
Write the serial number in the
space above for reference,
Serial
Number
Decal
• Assembly
•Operation
•Troubleshooting
•Part List and Drawing
USER'S MANUAL
Sears, Roebuck and Co., Hoffman Estates, IL 60179

TABLE OF CONTENTS
WARNING DECAL PLACEMENT .............................................................. 2
IMPORTANT PRECAUTIONS ................................................................ 3
BEFORE YOU BEGIN ...................................................................... 5
PART IDENTIFICATION CHART .............................................................. 6
ASSEMBLY ............................................................................... 7
HOW TO USE THE VIBRATION PLATFORM ................................................... 13
TROUBLESHOOTING ..................................................................... 17
PART LIST .............................................................................. 18
EXPLODED DRAWING .................................................................... 19
ORDERING REPLACEMENT PARTS .................................................. Back Cover
90 DAY FULL WARRANTY .......................................................... Back Cover
WARNING DECAL PLACEMENT
The warning decals shown here have been applied in
the locations shown. If a decal is missing or illegible,
call 1-888-533-1333 and request a free replacement
decal. Apply the decal in the location shown. Note:
The decals may not be shown at actual size.
User Weight: Max 300 LBS
Weight Crutch: Max 310 LBS
Leg Developer: Max 150 LBS
Weight Carriage: Max 150 LBS
Chest Fly Per Arm: Max 50 LBS
Product may not offer all listed exercises.
• Misuse of this machine may result in serious injury.
•Read user's manual prior to use and follow all warnings
and instructions.
•Do not allow children on or around machine.
• Keep body, clothing, and hair free and clear of
all moving parts.
label if dama or removed
2

IMPORTANT PRECAUTIONS
3

4

BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM ®
ACTIVATOR V7 vibration platform. The ACTIVATOR
V7 vibration platform offers whole body vibration
options designed to make tour workouts effective and
enjoyable.
For your benefit, read this manual carefully before
you use the vibration platform. If you have ques-
tions after reading this manual, please see the back
cover of this manual. To help us assist you, note the
product model number and serial number before con-
tacting us. The model number and the location of the
serial number decal are shown on the front cover of
this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Console
Dumbbell
Handlebar
Weight Rest
Reset/Off Circuit Breaker
Power Cord
Dumbbell
Stop Button
Start Button
Wheel
Base
5

PART IDENTIFICATION CHART
See the drawings below to identify small parts used in assembly, The number in parentheses by each drawing is
the key number of the part, from the PART LIST near the end of this manual. Note: Some small parts may
have been preattached. If a part is not in the hardware kit, check to see if it has been preattached. If a
part is missing, call t-888-533-t333.
©D
M10 Nylon
Locknut (32)
M5 x 38mm Screw (40)
M!O x 50mm Patch Screw (5!)
MIO Split
Washer (38)
MIO x 20mm
Patch Screw (28)
M4 x 16mm
Patch Screw (26) M4 x 19mm
Screw (45)
M!0 x 35mm Screw (34)
M10 x 55mm Patch Screw (20)
M!0 x 62ram Patch Screw (37)
H
M10 x 68mm Bolt (55)
M10 x 114mm Bolt (33)
6

ASSEMBLY
Before beginning assembly, carefully read the
following information and instructions:
•Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
• For help identifying small parts, see the PART
IDENTIFICATION CHART on page 6.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
• Assembly may require the following tools (not
included):
one adjustable wrench
one rubber mallet
one Phillips screwdriver
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
1, Attach a Rubber Spacer (29) and a Foot (13) to
the Lower Upright (!) with an M!0 x 35mm
Screw (34).
Next, locate the Wire Harness (43) inside the
Lower Upright (!). Connect the Wire Harness to
the base wire as shown. Then, pull the Wire
Harness out of the top of the Lower Upright.
Base
Wire
7

2. Tip: Be careful not to pinch the wires during
this step.
With the help of a second person, carefully tip
the Base (5) onto its side.
Attach the Lower Upright (1) to the Base (5)
with two M10 x 55mm Patch Screws (20), two
M10 Split Washers (38), two M10 x 68ram Bolts
(55), and two M10 Nylon Locknuts (32).
20 38
3. Tip: Orient the Wheel Bracket (35) so that
the arrow sticker is pointing upward.
Attach the Wheel Bracket (35) to the Lower
Upright (1) with two M10 x 20mm Patch Screws
(28).
28
4. Attach the Wheel (30) to the Wheel Bracket (35)
with an M!0 x 114mm Bolt (33) and an M!0
Nylon Locknut (32). Do not overtighten the
Nylon Locknut; the Wheel must rotate freely.
Note: If the Wheel (30) rattles when the
vibration platform is in use, tighten the M1O
Nylon Locknut (32) until the rattling stops.
32 3O
33
8

5. 5
Attach the Weight Rest (42) to the Weight Rest
Frame (41) with eight M5 x 38ram Screws (40).
Do not tighten the Screws yet.
40
42
40
40
6, Locate the wire tie inside the Upper Upright (36).
Insert the wire tie through the hole in the Weight
Rest Frame (41).
Next, attach the Upper Upright (36) to the
Weight Rest Frame (41) with two M10 x 50ram
Patch Screws (51) and two M!0 Split Washers
(38). Wire Tie,..__) Hole
/
7, Have a second person hold the Upper Upright
(36) near the Lower Upright (1).
See the inset drawing. Tie the lower end of the
wire tie to the Wire Harness (43) as shown.
Then, pull the upper end of the wire tie until the
Wire Harness is routed through the Upper
Upright (36).
ire Tie
43
9

8. Tip: Be careful not to pinch the wires during
this step.
Attach the Upper Upright (36) to the Lower
Upright (1) with four M10 x 20mm Patch Screws
(28) and four M!0 Split Washers (38).
See step 5. Tighten the eight M5 x 38ram
Screws (40).
28
28
9. Tip: Orient the Handlebar (39) so that the
sticker with an "R" is in the location shown.
Attach the Handlebar (39) to the Upper Upright
(36) with two M10 x 62mm Patch Screws (37)
and two M10 Split Washers (38).
10
10. Remove the four M4 x 12ram Self-tapping
Screws (27) from the back of the Console (3).
Set the Self-tapping Screws aside until step
13. 27
27
10