Pro-Form Fusion 6.0 LX User manual

Mode!No.PFSY5015.0
SedalNo.
WritetheseriaUnumberinthe
spaceaboveforfuturereference.
SeriaUNumberDecaU(UnderSeat)
Asamanufacturer,wearecom-
mittedto providingcomplete
customersatisfaction,ifyou
havequestions,or ifapartis
damagedormissing,PLEASE
CONTACTOURCUSTOMER
SERVICEDEPARTMENT
DIRECTLY.
CALLTOLL-FREE:
1-888-533-1333
Non.=Fd., 6 a.m.=6 p.m. MST
ON THE WEB:
www.proformservice.com
/ /
/ /
Read all precautions and instruc,
tions in this manual before using
this equipment, Save this manual
for future reference.
ourwe#s teat
www.proform°com
new products, prizes,
fitness tips, and much more!

TABLE OF CONTENTS
WARNING DECAL PLACEMENT ............................................................. 2
HMPORTANT PRECAUTHONS ................................................................ 3
BEFORE YOU BEGIN ...................................................................... 4
ASSEMBLY .............................................................................. 5
ADJUSTMENTS .......................................................................... 24
CABLE DHAGRAM ......................................................................... 27
WEHGHT RESHSTANCE CHART .............................................................. 29
EXERCHSE GUHDELHNES .................................................................. 30
ORDERHNG REPLACEMENT PARTS .................................................. Back Cover
LHMHTEDWARRANTY .............................................................. Back Cover
Note: A PART iDENTiFiCATiON CHART and a PART LiST/EXPLODED DRAWING are attached in the center of
this manual Remove the PART HDENTHFHCATHONCHART and PART LHST/EXPLODED DRAWHNG before begin-
ning assembHy,
WARNING DECAL PLACEMENT
The decaJs shown here have been placed on
the weight system, mfa decal is missing or
illegible, please call the toll-free teJephone
number on the front cover of this manual
and order a free replacement decal. Apply
the decaJ in the location shown.
Misuse of this machine may resumtin serious injury.
Read user's manuamprior to use and follow am_warnings
and instructions.
Do not aH_owchiHdren on or around machine.
Keep body, cHothing, and hair free and cHearof amHmoving
parts. Habelif removed.
hands and
ecs dear of
this area.
PROFORM is a registered trademark of iCON IP, Inc,
2

iMPORTANT PRECAUTIONS
AWARNmNG: Tored.oethedskofse.ousnjury,readthefo,ow ngmportantprecautions
before using the weight system.
Read all instructions in this manual and all
warnings on the weight system before using
the weight system. Use the weight system
only as described in this manual.
2=
that the cables are on the pulleys. Replace aH
cables at least every two years.
It is the responsibility of the owner to ensure
that aH users of the weight system are ade-
quately informed of all precautions.
10. The weight system is designed to support a
maximum user weight of 300 pounds.
11. The weight system is designed to be used
only with the included weight. Do not use the
weight system with dumbbells or any other
3. The weight system is intended for home use type of weight to increase the resistance.
only. Do not use the weight system in any
commercial rental or institutional setting. 12. Always stand on the foot plate when per-
forming an exercise that couJd cause the
4. Keep the weight system indoors, away from weight system to tip.
moisture and dust. Place the weight system
on a level surface, with a mat beneath it to 13. Never release the arms, leg lever, lat bar, leg
protect the floor or carpet. Make sure that press, ab strap_ or handle while weights are
there is enough clearance around the weight raised. The weights will fall with great force.
system to mount, dismount, and use the
weight system. 14. Always disconnect the lat bar from the
weight system when performing an exercise
5. inspect and property tighten aJl parts regular- that does not use the matbar.
ly. Aepiace any worn parts immediately.
6. Keep children under 12 and pets away from
the weight system at aHtimes.
7. Keep bands and feet away from moving parts.
8. Always wear athletic shoes for foot protec-
tion while exercising.
9. Make sure that the cables remain on the puJ°
leys at aJl times, if the cables bind as you are
exercising, stop immediately and make sure
15. Do not use the weight system with the top
weight pinned in an elevated position.
16 Always secure the weight stack with the lock
pin and lock after exercising to prevent
unauthorized use of the weight system (see
LOCKING THE WEIGHT STACK on page 25).
17. if you feel pain or dizziness at any time while
exercising, stop immediateJy and begin cool-
ing down.
A kWAF{NING: Beforebeginningthisoranyexerciseprogram,consultyourphysician.This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read aH instructions before using, iCON assumes no responsibility for personaJ injury or property
damage sustained by or through the use of this product.
3

BEFORE YOU BEGIN
Thank you for sebcting the versatib PROFORM +_
FUSION 6,0 LX weight system, The weight system
offers a sebction of weight stations designed to deveP
op every major muscle group of the body, Whether
your goal is to tone your body, build dramatic muscb
size and strength, or improve your cardiovascular sys-
tem, the weight system will help you to achieve the
specific results you want,
For your benefit, read this manuaJ carefully before
using the weight system, if you have questions after
reading this manual, see the front cover of this manu-
al, To help us assist you, please note the product
model number and serial number before calling, The
model number is PFSY5015,0, The serial number can
be found on a decal attached to the weight system
(see the front cover of this manual),
To avoid a registration fee for any service needed
under warranty, you must register the weight sys-
tem at www.proformservice.com/registration.
Before reading further, please review the drawing below
and familiarize yourself with the parts that are labeled,
Right Side Left Side High Pulley
Station
Backrest
Cud Pad
]
/
//
Leg Lever
Low Pulley
Station
Foot
Plate
Weight
Note: The terms "right side" and "left side" are determined
relative to a person sitting on the seat; they do not corre-
spond to right and left on the drawings in the manual
\
\
Lat Bar
Military Press Arm
Adjustable Backrest
Press Arm
P ress
ASSEMBLED DiMENSiONS:
Height: 80 in, /203 cm
Width: 80 in, /203 cm
Depth: 96 in, /244 cm
4

Make Assembly Easier for Yourself
Everything in this manual is designed to
ensure that the weight system can be assem-
bled successfully by almost anyone. Before
beginning assembly, make sure to read the
information on this page. This brief intro-
duction will save you much more time than
it takes to read it.
Hire an Authorized Service Technician
To hire an authorized service technician to
assemble the weight system, call toil-free
1-800-445-2480.
Assembly Requires Two Persons
For your convenience and safety, assembb the
weight system with the heUpof another person,
Set Aside Enough Time
Assembling the weight system may require severaU
hours. By deciding to make the task enjoyaMe,
assemMy wHUgo smootHy. You may want to assem-
bb the weight system over a couple of evenings,
SeJect a Location for the Weight System
Because of its weight and size, the weight system
should be assembled in the location where it will be
used, Make sure that there is enough clearance to
walk around the weight system as you assemble it.
Now to Unpack the Box
To make assembly as easy as possible, we have
divided the assembly process into four stages, The
parts needed for each stage are found in individual
bags, Important: Wait until you begin each stage
to open the parts bag for that stage. Place all
parts of the weight system in a cleared area and
remove the packing materials, Do not dispose of the
packing materials until assembly is completed,
The included AHen wrench _ and grease,
and the following toots (not included} may be
required for assembly:
*Two adjustable wrenches
*One standard screwdriver
*One phillips screwdriver
*One rubber mallet
*A small amount of soapy water, and clear tape or
masking tape.
Note: Assembly may be more convenient if you have
a socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
Now to identify Parts
To help you identify the small parts used in assembly,
we have included a PART IDENTIFICATION CHART
in the center of this manual. Note: Some parts may
have been pre-attached. If a part is not in the parts
bag, check to see if it has been pre-attached.
Now to Orient Parts
As you assemble the weight system, make sure all
parts are oriented exactly as shown in the drawings,
Tightening Parts
Tighten all parts as you assemble them, unless
instructed to do otherwise,
Questions?
if you have questions after reading the assembly
instructions, see the front cover of this manual.
The Four Stages of the Assembly Process
Frame Assembly--You wiii begin by assembling
the base and the uprights that form the skeleton of
the weight system,
Arm AssembJy--During this stage you wiii assem-
ble the arms and the moving parts.
Cable Assembly--During this stage you wiii attach
the cables and pulleys that connect the arms to the
weights,
Seat Assembly--During the final stage you wiii
assemble the seats, the backrests, and other parts,

Beforebeginningassembly,makesureyou
understandtheinformationin theboxon
sma!l parts, use the PAR]" mDENTmF!CATmON
CHART in the center of this manual
Attach the Foot Hate (90) to the Right Base (1)
with an M10 x 120mm BoUt(97), two M10
Washers (10% and an M10 NyUonLocknut (111),
Do not overtighten the Loeknut; the Foot Plate
must be able to pivot easily.
Unsertfour M10 x 80mm Carriage BoUts(112) up
through the Right Base (1), Hace a piece of tape
over the boutheads to hoUdthe BoUtsin pUace,
Unserttwo M10 x 80mm Carriage BoUts(112) up
through the Left Base (2), Hace a piece of tape
over the boutheads to hoUdthe BoUtsin place,
Attach the Center Base (5) to the Right and Left
Bases (1, 2) with four M10 x 70mm Bolts (57),
four M10 Washers (10% and two M10 Nylon
Locknuts (111), Do not tighten the Bolts yet.
9O
57
112
112
109 97
112
109 109
6

4, 4
Attach the Center Upright (9) to the Right and
Left Bases (1,2) with four MIO x 70mm Bolts
(57), four MIO Washers (10% and two MIO
Nylon Locknuts (111), Do not tighten the BoJts
yet,
Attach the Right Upright (7) to the Right Base (1)
with two MIO x 90mm Bolts (102) and two MIO
Nylon Locknuts (111), Do not tighten the
Locknuts yet,
9--
02
7

6, 6
Attach the Right Seat Upright (11) to the Right
Base (1) with the indicated MIO x 80mm Carriage
BoUts(112) and two MIO Nybn Locknuts (111),
Attach the CurUPost Upright (10) to the Right
Base (1) with the indicated MIO x 80mm Carriage
BoUts(112) and two MIO Nybn Locknuts (111),
Attach the Left Upright (8) to the Left Base (2)
with two MIO x 90mm BoUts(102) and two MIO
Nybn Locknuts (111). Do not tighten the
Locknuts yet.
lO-¢_/ /
/ /
/111 /
/
/_
111
1
:_111
2
o
8

9, Attach the Left Seat Upright (14) to the Left Base
(2) with the indicated MIO x 80mm Carriage BoUts
(112) and two MIO NyUonLocknuts (111),
10, Attach the Right Top Frame (3) to the Center
Upright (9) with two MIO x 70mm Bolts (57), two
MIO VVashers (10% and an MIO Nylon Locknut
(111), Do not tighten the Bolts yet.
Attach the Right Top Frame (3) to the Right
Upright (7) with two MIO x 90mm Bolts (102) and
two MIO Nylon Locknuts (111), Do not tighten
the Locknuts yet.
11, Attach the Left Top Frame (4) to the Center
Upright (9) with two MIO x 70mm Bolts (57), two
MIO Washers (109), and an MIO Nylon Locknut
(111), Do not tighten the Bolts yet.
Attach the Left Top Frame (4) to the Left Upright
(8) with two MIO x 90mm Bolts (102) and two
MIO Nylon Locknuts (111), Do not tighten the
Locknuts yet.
12, Attach the Butterfly Frame (24) to the Right Top
Frame (3) with two MIO x 65mm Bolts (110) and
an MIO Nylon Locknut (111), Do not tighten the
Bolts yet.
Attach the Butterfly Frame (24) to the Right
Upright (7) with two MIO x 35mm Screws (113),
Do not tighten the Screws yet.
10
11
12
111 .14
,_ 111
2
112
111 111
109
4
1 111
109
9

13, Orient a Weight Guide (30) with the indicated
hoUecloser to the bottom, Attach the Weight
Guide to the Center Base (5) with an MIO x
65mm BoUt(110), two MIO Washers (109), a 1/2"
Spacer (68), and an MIO NyUonLocknut (111),
SHde a Weight Bumper (66) onto the Weight
Guide,
Attach the other three Weight Guides (30) to
the Center Base (5) in the same manner.
Tighten the MIO × 70ram Bolts (57) used in
step 3.
14, SHde eUeven Weights (34), with the pin grooves
on the bottom, onto a set of Weight Guides (30),
Orient a Weight Tube (75) as shown, Unsertthe
Weight Tube into the stack of Weights (34),
SHde another Weight (34) onto the set of Weight
Guides (30),
Repeat this step with the other stack of
Weights (34}.
13
Pin
Groove
10

15, Attach the Center Top Frame (6) to the Right and
Left Top Frames (3, 4) with four M10 x 70mm
BoUts(57), four M10 Washers (109), and two M10
NyUonLocknuts (111), Do not tighten the BoJts
yet.
Attach a Weight Guide (30) inside the Center Top
Frame (6) with an M10 x 65mm BoUt(110), two
M10 Washers (109), a 1/2" Spacer (68), and an
M10 NyUonLocknut (111),
Attach the other three Weight Guides (30} to
the Center Top Frame (6} in the same manner.
Tighten the bolts, screws and [ocknuts used
in steps 4, 5, 8, 10, 11, and 12.
16, AppUygrease to 2" Bushing (63), Attach the Leg
Lever (15) and the 2" Bushing to the CurUPost
Upright (10) with an M10 x 70mm BoUt(57) and
an M10 NyUonLocknut (111),
17, AppUygrease to a 3" Bushing (71) and the two
Large Round Bushings (61) in the Right ButtedUy
Arm (23), Attach the ButtedUy Arm and 3" Bushing
to the Butterfly Frame (24) with an M10 x 100mm
BoUt(85) and an M10 NyUonLocknut (111),
Repeat this step with the Left Butterfly Arm
(22}.
15
57
16
17
111 _10
85
61 Grease ,'!!'
// /
/ !J
/ I
/ /
/ i
/ I
//
/ I
_rease 24
111
57
11

18. AppUygrease to the 1 3/4" Bushing (64). Attach
the MHitary Press Frame (20) and the 1 3/4"
Bushing inside the Left Upright (8) with an MIO x
63mm BoUt(104) and an MIO NyUonLocknut
(111).
19. AppUygrease to an MIO x 45mm BoUt(95). Attach
the MHitary Press Arm (21) to the MHitary Press
Frame (20) with the BoUtand an MIO NyUon
Locknut (111). Do not overtighten the Locknut;
the Mititary Press Arm must be able to pivot
easily.
20. AppUygrease to a 2 3/4" Bushing (65). Attach the
Press Frame (13) and the 2 3/4" Bushing to the
Left Base (2) with an MIO x 90mm BoUt(102) and
an MIO NyUonLocknut (111).
21. Attach the Right Press Arm (26) to the Press
Frame (13) with two MIO x 70mm BoUts(57) and
two MIO NyUonLocknuts (111).
Attach the Left Press Arm (25) to the Press
Frame (13} in the same manner.
19
111
2O
\
111
Grease 21
111
12

22, Apply grease to an M10 x 70mm Bolt (57), Attach
a Press Arm Handle (27) to the Left Press Arm
(25) with the Bolt and an M10 Nylon Locknut
(111), Do not overtighten the Locknut; the
Press Arm Handle must be able to pivot easily.
Repeat this step with the other Press Arm
Handle (27} and the Right Press Arm (26}.
23, AppUygrease to a 2 3/4" Bushing (65), Attach the
Leg Press (12) and the 2 3/4" Bushing to the Left
Base (2) with an M10 x 95mm BoUt(108) and an
M10 NyUonLocknut (111),
24, Apply grease to an M10 x 75mm Bolt (96), Attach
the Leg Press Hate (29) and a 2 3/4" Bushing
(65) to the Leg Press (12) with the BoUtand an
M10 Nylon Locknut (111), Do not overtighten the
Locknut; the Leg Press Plate must be able to
pivot easily.
25, During steps 25=54, refer to the CABLE DIA-
GRAMS on pages 27 and 28 to identify the
cables and ensure proper cable routing.
Locate the Butterfly Cable (73}. Attach the
CaMe to the Right Upright (7) with an M8 x 25mm
ShouUder BoUt(92) and an M8 NyUonLocknut
(101), Make sure that the Cable end can pivot
easily around the shoutder of the Bolt.
24
25
111.
26
111
\29
13

26, Wrap the Butterfly CaMe (73) around a Pulley
(43), Attach the Pulley, a CaMe Trap (48), an MIO
Washer (10% and two Finger Guards (45) to the
Left Butterfly Arm (22) with an MIO x 50mm BoUt
(106) and an MIO NyUonLocknut (111), Make
sure that the CabJe Trap is oriented to hold
the Cable in the groove of the Pulley.
27, Wrap the Butterfly CaMe (73) around a Pulley
(43), Attach the Pulley, a CaMe Trap (48), an MIO
Washer (10% and two HaUlFinger Guards (46) to
the Right Upright (7) with an MIO x 120mm BoUt
(97) and an MIO NyUonLocknut (111), Make sure
that the Cable Trap is oriented to hold the
Cable in the groove of the Pulley.
28, Wrap the Butterfly Cable (73) around a Pulley
(43), Attach the Pulley, a CaMe Trap (48), an MIO
Washer (10% and two Finger Guards (45) to the
Right Butterfly Arm (23) with an MIO x 50mm BoUt
(106) and an MIO NyUonLocknut (111), Make
sure that the Cable Trap is oriented to hoJd
the Carte in the groove of the Pulley.
29, Wrap the Butterfly CaMe (73) under the "V"-pulley
(44), Attach the "V"opulley, the Long Cable Trap
(83), an MIO Washer (109), and two Finger
Guards (45) to the Right Upright (7) with an MIO
x 150mm Bolt (94) and an MIO Nylon Locknut
(111), Make sure that the CabJe Trap is orient-
ed to hold the CaMe in the groove of the "V"-
puHeyo
26
27
28
29
46
/
111
,\÷
48
43.
_111
111_ 45
83
14

30, Wrap the Butterfly CaMs (73) over a Pulley (43),
Attach the Pulley to the Right Top Frame (3) with
an MIO x 40mm BoUt(116) and an MIO NyUon
Locknut (111),
Repeat this step with another Puttey (43}.
31, Wrap the Butterfly CabUs (73) under a Pulley (43),
Attach the Pulley, a CaMe Trap (48), and two HaUl
Finger Guards (46) at the second hoUsfrom the
top of the pair of Pulley Hates (49) with an MIO x
50mm BoUt(106) and an MIO NyUonLocknut
(111), Makes sure that the Cable Trap is orient-
ed to hold the Cable in the groove of the
Pulley.
32, Wrap the Butterfly Cable (73) over a Pulley (43),
Attach the Pulley to the Right Top Frame (3) with
an MIO x 45mm BoUt(95) and an MIO NyUon
Locknut (111),
33, Wrap the Butterfly CaMs (73) over a Pulley (43),
Attach the Pulley to the Center Top Frame (6)
with an MIO x 45mm BoUt(95) and an MIO NyUon
Locknut (111),
3O
31
32
33
111 43 73
\ 95
\43
73
116
106
95
15

34. Attach the Butterfly CaMe (73) and a Weight Cap
(67) to the indicated Weight Tube (75) with an
MIO x 50mm BoUt(106) and an MIO NyUon
Locknut (111).
35. Locate the Low CabJe (70). Route the CaMe
through the Leg Lever (15) and the CurUPost
Upright (10).
Attach a Pulley (43) to the Leg Lever (15), over
the Low Cable (70), with an MIO x 45mm Bolt
(95) and an MIO Nylon Locknut (111).
36. Attach a Pulley (43) inside the Curl Post Upright
(10), over the Low Cable (70), with an MIO x
65mm Bolt (110), two MIO Washers (109), two
1/2" Spacers (68), and an MIO Nylon Locknut
(111).
37. Route the Low CaMe (70) through the Right Seat
Upright (11) and the Right Upright (7) and under a
PuUUey(43). Attach the PuUUey,an MIO Washer
(109), and two HaUlFinger Guards (46) to the
Right Base (1) with an MIO x 45mm BoUt(95) and
an MIO NyUonLocknut (111).
34
35
,, 73-
11
6]
106
75-
36
111
43
7O
15
95
111 43
110
J
68
37
109
16

38, Wrap the Low CaMe (70) over a Pulley (43),
Attach the Pulley, a CaMe Trap (48), and two HaUl
Finger Guards (46) at the bottom hoUeof the pair
of Pulley Hates (49) with an MIO x 50mm BoUt
(106) and an MIO NyUonLocknut (111), Makes
sure that the CabJe Trap is oriented to hold
the Cable in the groove of the Pulley.
39, Attach the Low CaMe (70) inside the Right Base
(1) with an MIO x 65mm BoUt(110), two MIO
Washers (109), and an MIO NyUonLocknut (111),
40, Locate the High Cable (88}. Route the CaMe up
through the Left Top Frame (4) and over a Pulley
(43), Attach the Pulley inside the Top Frame with
an MIO x 65mm BoUt(110), two MIO Washers
(10% two 1/2" Spacers (68), and an MIO NyUon
Locknut (111),
41, Route the High CaMe (88) over a Pulley (43) and
down through the Left Top Frame (4), Attach the
Pulley inside the Top Frame with an MIO x 65mm
BoUt(110), two MIO Washers (109), two 1/2"
Spacers (68), and an MIO NyUonLocknut (111),
42, Wrap the High CaMe (88) under a Pulley (43),
Attach the Pulley, a CaMe Trap (48), an MIO
Washer (10% and two HaUlFinger Guards (46) to
the Small Pulley Plate (50) with an MIO x 50mm
Bolt (106) and an MIO Nylon Locknut (111),
Makes sure that the CabJe Trap is oriented to
hotd the Cabte in the groove of the Pulley.
38
39
4O
41
42
111 o
49
1 110
110
109
43 111
43
109 109
110 \
\
43
5O
17

43, Route the High CabUe(88) up through the Left
Top Frame (4) and over a Small Pulley (84),
Attach the Pulley inside the Top Frame with an
MIO x 65mm BoUt(110), two MIO Washers (10%
two 1/2" Spacers (68), and an MIO NyUonLocknut
(111),
44, Route the High CaMe (88) over a SmaUUPuUUey
(84) and down through the Left Top Frame (4),
Attach the PuUUeyinside the Top Frame with an
MIO x 65mm BoUt(110), two MIO Washers (10%
two 1/2" Spacers (68), and an MIO NyUonLocknut
(111),
45, Wrap the High CaMe (88) under a PuUUey(43),
Attach the PuUUey,an MIO Washer (109), and two
HaUlFinger Guards (46) to the MiUitaryPress
Frame (20) with an MIO x 45mm BoUt(95) and an
MIO NyUonLocknut (111),
46, Wrap the High CabUe (88) over a PuUUey(43),
Attach the PuUUeyto the Left Top Frame (4) with
an MIO x 45mm BoUt(95) and an MIO NyUon
Locknut (111),
47, Wrap the High CaMe (88) over a PuUUey(43),
Attach the PuUUeyto the Center Top Frame (6)
with an MIO x 45mm Bolt (95) and an MIO Nylon
Locknut (111),
43
44
45
46
47
110
110
109 68
" _84 88
109 68
95
88
84
46
111
/
111
18

48, Attach the High CaMe (88) and a Weight Cap
(67) to the indicated Weight Tube (75) with an
MIO x 50mm BoUt(106) and an MIO NyUon
Locknut (111),
49, Locate the Press CabJe (72}. Attach the CaMe to
the Left Base (2) with an M8 x 25mm ShouUder
BoUt(92), Make sure that the Cable end can
pivot easily around the shoulder of the Bolt.
50, Wrap the Press CaMe (72) over a Pulley (43),
Attach the Pulley, a CaMe Trap (48), an MIO
Washer (10% and two Finger Guards (45) to the
Leg Press (12) with an MIO x 120mm BoUt(97)
and an MIO NyUonLocknut (111), Make sure that
the CabJe Trap is oriented to hold the Cable in
the groove of the Pulley.
51, Wrap the Press CaMe (72) under a Pulley (43),
Attach the Pulley, a CaMe Trap (48), an MIO
Washer (10% and two Finger Guards (45) to the
Left Seat Upright (14) with an MIO x 120mm BoUt
(97) and an MIO NyUonLocknut (111), Make sure
that the Cable Trap is oriented to hold the
Cable in the groove of the Pulley.
52, Wrap the Press CabUe(72) under a Pulley (43),
Attach the Pulley, a CaMe Trap (48), an MIO
Washer (10% and two HaUlFinger Guards (46) to
the Press Frame (13) with an MIO x 45mm Bolt
(95) and an MIO Nylon Locknut (111), Make sure
that the Cable Trap is oriented to hotd the
Cable in the groove of the Pulley.
48 _'_
49
50
51
52
111
-67
10(
72
\
)9 72
45
_-12
43 97
45
111
109
46.
95
72
97
19

53, Wrap the Press CaMe (72) under a Pulley (43),
Attach the Pulley, a CaMe Trap (48), an MIO
Washer (10% and two Haft Finger Guards (46) to
the Left Base (2) with an MIO x 130mm BoUt
(107) and an MIO NyUonLocknut (111), Make
sure that the CabJe Trap is oriented to hold
the Cable in the groove of the Pulley.
54, Attach the Press CaMe (72) to the Small Pulley
Hate (50) with an M6 Washer (114) and an M6
NyUonLocknut (103), See the inset drawing. Do
not completely tighten the Locknut; it should
be tightened so that onJy two threads of the
Cable show past the Locknut.
55, Attach the CurUPad (38) to the CurUPost (16) with
two M6 x 25mm Screws (99),
56, Attach a Backrest (35) to the Right Upright (7)
with four M6 x 25mm Screws (99),
54
55
56
46
48 107
43 72
Q @
-5O
103
7;
/
//
//
/ /
/
/,
'--s
99
2O