PRO SIGNAL PSG3078 User manual

PSG3078
HDMI 1080P EXTENDER OVER CAT5e/6
1

IMPORTANT SAFETY INFORMATION
Please read these instructions carefully before use and retain for future reference.
• Check that the voltage indicated on the PSU rating plate corresponds with that of the
local network before connecting to the mains power supply.
• Do not expose to excessive heat or locate where damp or moisture may enter the
device.
• Ensure there is sufcient ventilation to allow any generated heat to dissipate.
OVERVIEW
• This device can extend one HD source to a display or projector using CAT5e or CAT6
cables.
• The extending distance is up to 60m.
• Supports 24/50/60fs/1080p/720p/576p/576i/480p/480i CEC modes.
• Audio formats supported DTS-Dolby/Dolby trueHD/LPCM7.1/DTS/Dolby-AC3/DSD.
WHAT’s IN THE BOX
• HDMI Transmitter
• HDMI Receiver
• 5V DC Power Supply x 2
• IR Transmitter
• IR Receiver
• User’s Manual
INSTALLATION
• Please make sure all devices you wish to connect have been powered off.
• Connect the source device to the transmitter using appropriate HDMI cable up to 20m.
• Connect premium CAT5e/6 cable up to 30m/60m long to the output of the transmitter
and to the input of the receiver.
• Connect the IR RX to the IR Input jack on the receiver.
• Ensure the IR receiver is located where it is visible to the source device remote
control unit.
• Connect the IR TX to the IR Output jack on the transmitter and direct the IR sender
towards the source device remote control sensor.
• Connect the HDMI output using appropriate HDMI cable up to 20m long to the display.
NOTE: Premium quality HDMI and CAT6 leads must be used to achieve the maximum
audio/video quality and stability over greater distances.
• Connect the DC side of the 5V power supplies to the transmitter and the receiver then
connect the AC side of the power supplies into the mains supply.
• The S1 LED lights green when the power is applied.
• Power on the source device and the display.
• The device reads the output display EDID information and adjusts output accordingly
for the devices attached.
• The S2 LED lights when a HDMI signal is being processed.
2

CONNECTION DIAGRAM
• Use a soft cloth to wipe off any dust. If the device is very dirty, use a damp cloth and
wipe dry.
• Do not use any chemicals, abrasives or solvents that could damage the casing.
3
SPECIFICATIONS
MAINTENANCE
Operating environment -15 to 55oC, Humidity 5 to 90%
Power requirement 220-240V~50Hz
Power supply 5V DC 1A
Power consumption 800mA
HDMI Input 24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i
Audio formats output LPCM7.1/DTS/Dolby-AC3/DSD
Audio formats input DTS-HD/Dolby-trueHD/LPCM7.1/DTS/Dolby-AC3/DSD
Input video signal 0.5~1.5Volts p-p
Output DDC signal 5 Volts p-p (TT1L)
Max baud rate 4.95Gbps
Max bandwidth 165MHz
Dimensions (each) 83 x 48 x 22mm
Weight (not inc PSU) 104g (each approx)

INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical & Electronic
Equipment (WEEE). Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used. Contact your local
authority for details of recycling schemes in your area.
Made in China. PR2 9PP
Man Rev 1.0
4