PRO SIGNAL PSG3084 User manual

PSG3084
HDMI OVER Cat6/6a/7 EXTENDER
1

WHAT’s IN THE BOX
OVERVIEW
IMPORTANT SAFETY INFORMATION
INSTALLATION
• HDMI extender using HDBaseT, transmits audio and HD video signal.
• Extends 1080p video and audio transmission range via Cat6, of up to 50 meters.
Please read these instructions carefully before use and retain for future reference.
Requirements
• An HDMI source device with HDMI OUTPUT interface, DVD, PS3, STB, PC etc set to
a maximum 1080i/p output resolution.
• A display device with HDMI INPUT port, SDTV, HDTV, projector etc.
• When using electrical appliances basic safety precautions should always be followed..
• Do not expose the units to moisture or dust and keep any ventilation slots clear.
• Do not connect or disconnect cables or the units from the source or display devices
while powered on and in use.
• HDMI 1.3 compatible uncompressed HDMI video signal.
• Apply HDBaseT extend technology HDCP 1.2 compatible.
• Supports full HD 1080p@60Hz signal over Cat6 up to 50 meters.
• Support stereo audio.
• Automatically identies and congures a variety of display modes.
• Simple and convenient plug and play installation, no setting up required.
FEATURES
2
• HDMI Transmitter
• HDMI Receiver
• USB Power Cable x2 off
• User Manual
• Network cables UTP/STP Cat6/Cat6A/Cat7 network cables, to IEEE-568B.
Connections
• Connect the transmitter TX unit into the HDMI output port on the signal source
equipment.
• Connect the receiver RX unit into the HDMI input port on the display device.
• Connect both Receiver and Transmitter via Cat6/Cat6A or Cat7 network cables
• Plug the USB cables into the Transmitter and Receiver units and connect to a suitable
USB socket for power, or to a mains adaptor with USB output (not included).
• Power on the signal source and the display.
• Press the ‘LENGTH’ button on the receiver to auto-adjust the setting for the network
cable length. This is then stored in memory until the button is pressed again.
Note: It is recommended to use a network cable length of between 15 and 50metres. If the
cable is too short the signal strength may be too high resulting in loss of display. Too long
and the output may degrade.

3
1. RJ45 network cable socket.
2. HDMI connector (plug into source device HDMI output socket).
3. USB power input socket.
1. RJ45 network cable socket.
2. HDMI connector (plug into source device HDMI output socket).
3. Length set button
4. USB power input socket.
Transmitter Panel Connections
Receiver Panel Connections
Adjustment
• Users can press ”LENGTH” button to adjust the transmission distance of this device
automatically or manually. The previous setting is retained in memory.
• Press twice and the unit will adjust the distance according to the network cable length
automatically.
• Continuing to press the button will select manual mode for adjusting the transmission
distance. There are 10 steps each selected by a further press.
• After all 10 steps the setting will loop back to the auto adjust transmission mode.

INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical & Electronic
Equipment (WEEE). Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used. Contact your local
authority for details of recycling schemes in your area.
Made in China. PR2 9PP
Man Rev 1.0
MAINTENANCE
• Clean the outside casings with a soft cloth lightly moistened with mild soap and water.
Never use any abrasive or solvents.
• Do not allow moisture to enter the devices.
SPECIFICATIONS
Parameter Description
HDMI
Standards HDMI 1.3, HDCP 1.2
Resolution supported
480i@60Hz, 480p@60Hz, 576i@50Hz,
576p@50Hz, 720p@50/60Hz,
1080i @50/60Hz. 1080p@50/60Hz
Audio format Stereo L/R
Max transfer rate 6.75Gbps
Network
Standards Cat6, Cat6a, Cat7
Cat6 Transmission length 50m: Up to 1080P@60Hz 36bpp
Protection
Level
Complete Electrostatic
Protection
1a contact discharge level 3
1b air discharge level 3
Standard IEC61000-4-2
Operating
Environment
Working temperature 0~50oC (0~90% humidity)
Storage temperature -10oC~70oC
Power Voltage 5V DC via USB
Weight TX:10g RX:10g
Dimensions (W x D x H) 71.5 x 26 x 11 mm each unit
4