PRO SIGNAL PSG3424 User manual

1
4K 30Hz 10M WIRELESS EXTENDER
PSG3424

2
IMPORTANT SAFETY INFORMATION
Please read these instructions carefully before use and retain for future reference.
When using electrical appliances basic safety precautions should always be followed.
• To prevent re or shock hazard, do not expose this product to rain or moisture.
• Check that the power supply matches the mains voltage.
• Only use the power supply provided or one of identical specication.
• Beware of static electricity which may damage the device. Use ESD precautions
when installing.
• Do not plug or unplug cables while the devices are powered on.
WHAT'S INCLUDED
• HDMI Transmitter and Receiver
• 2 x Power Adapter 230VAC to 5VDC 1A
• Operation Manual
• Resolution up to 1080p 3D.
• Low power consumption.
• Uncompressed transmission, zero latency.
• Support CEC.
• <30 meters range transmission in line of sight.
• Resolution supported is up to 4Kx2K@30Hz ultra HD.
• Supports Dolby, TrueHD, DTS-HD Master Audio and LPCM digital audio streams up
to 7.1 channels audio.
• Supports point to point (Max 2kits within a room), and 2 to 1 conguration.
• HDMI Wireless Extender includes zero latency Transmitter and Receiver to transmit
high denition video and audio to any HDTV display up to 30 meters without any
delay.
• Supports resolutions up to 4Kx2K@30Hz(3840x2160@30Hz), supports 1080p 3D,
CEC, and 7.1-channels of High Bit Rate (HBR) lossless digital audio such as Dolby
TrueHD, DTS-HD Master Audio.
• Zero compression and zero latency, supporting point to point conguration, and
also 2 to 1 conguration.
NOTE: Transmission distance will vary due to the environment and to the conguration.
OVERVIEW
FEATURES
Transmitter

3
1. Power input Connect with PSU.
2. HDMI input Connect with HDMI source device.
3 Micro USB Connect to the source device USB port (optional).
4. Transmission LED Slow ash LED indicates the unit has started radio
transmission and has not yet found the receiver, transmitter
is in scan mode, searching for a matching receiver.
Fast ash LED indicates the transmitter and receiver have
been connected well with each other;
LED solid on means the transmitter and receiver have
established an audio or video connection, transmission in
operation.
5. Power LED Illuminates when the power is switched on.
6. Reset button Restores the device to factory setting.
1. Power input Connect with PSU.
2. HDMI input Connect with HDMI source device.
3 Micro USB Connect to the source device USB port (optional).
4. Transmission LED Slow ash LED indicates the unit has started radio
transmission and has not yet found the receiver, transmitter
is in scan mode, searching for a matching receiver.
Fast ash LED indicates the transmitter and receiver have
been connected well with each other;
LED solid on means the transmitter and receiver have
established an audio or video connection, transmission in
operation.
5. Power LED Illuminates when the power is switched on.
6. Reset button Long press (>10 seconds): set to factory default
When the button is short pressed on the receiver if other
transmitter sources are available in its network, the receiver
will give up the change connection to the next available
source
Receiver

4
INSTALLATION
• Connect the transmitter HDMI input with HDMI source device.
• Connect the receiver HDMI output with HDMI display device.
• Connect the power supplies to both transmitter and receiver and plug into the mains
supply and turn on the power.
• It is recommended that the same space should not have more than two groups of
devices working at the same time.
• If possible face the transmitter and receiver towards each other for maximum 30m
transmission range.
• If there is no line of sight possible the transmission range will be reduced
accordingly, also other environmental interference may affect transmission range
and signal quality such as microwave, wireless mouse and wireless keyboard etc.

5
Voltage/Current DC 5V/1A
Power consumption TX: <2.5W RX: <2.5W
HDMI compliance HDMI 1.4
HDCP compliance HDCP 2.2
HDMI resolution 80i@60Hz, 480p@60Hz, 576i@50Hz. 576p@50Hz.
720p@50/60Hz. 1080i@50/60Hz. 1080p@50/60Hz
1080p@50/60Hz/120Hz, 3840x2160@24/30Hz
Audio formats supported CH 7.1/LPCM/DTS-HD/Dolby-AC3
Maximum transfer rate 10.2Gbps
Input and output TMDS
signal
0.7~1.2Vp-p(TMDS)
Input and output DDC
signal
5Vp-p(TTL)
Transmission method 60GHz wireless
Transmission range <30m in line of sight when TX & RX placed face to face
Latency Zero
Working temperature 0~40°C
Storage temperature -20~70°C
Humidity 0~90%RH (no condensation)
Dimension 79.8(W) x 45.7(D) x 54.0(H)mm
Material Alloy
Weight TX: 120g RX: 120g
SPECIFICATIONS
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical
& Electronic Equipment (WEEE). Any WEEE marked products must not be mixed with
general household waste, but kept separate for the treatment, recovery and recycling
of the materials used. Contact your local authority for details of recycling schemes in
your area.
Made in China. PR2 9PP
Man Rev 1.0
CLEANING & MAINTENANCE
Clean the outside casing with a soft cloth lightly moistened with mild soap and water.
Never use any abrasive or solvents.