PRO SIGNAL PSG3424 User manual

1
4K 30Hz SDR 10M WIRELESS HDMI EXTENDER
PSG3424

2
IMPORTANT SAFETY INFORMATION
Please read these instructions carefully before use and retain for future reference.
When using electrical appliances basic safety precautions should always be followed.
To prevent re or shock hazard, do not expose this product to rain or moisture.
• Check that the power supply matches the mains voltage.
• Only use the power supply provided or one of identical specication.
• Beware of static electricity which may damage the device. Use ESD precautions
when installing.
• Do not plug or unplug cables while the devices are powered on.
WHAT'S INCLUDED
• HDMI Transmitter and Receiver
• 2 x Power Adapter 230VAC to 5VDC 1A
• Operation Manual
• 60GHz Wireless Extender with zero transmission latency.
• Range up to 1080p @ 30 meters. 10 meters 4K 30Hz SDR.
• Low power consumption.
• Uncompressed transmission, zero latency.
• Support CEC pass through.
• Maximum 30M visible “line of sight” transmission range @ 1080p 60Hz.
• Maximum supported resolution is up to 4K@30Hz standard dynamic range (SDR).
• Supports Dolby, TrueHD, DTS-HD Master Audio and LPCM digital audio streams up
to 7.1 channels audio.
• Supports point to point (Max 2 kits within a room), and 2 to 1 conguration.
• HDMI Wireless “Line of sight “transmission with zero latency.
• The transmitter and receiver can be used to transmit high denition video and audio
to any HDTV display in the same room or area up to 30 meters away without any
transmission delay.
• This product supports resolutions up to 4K@30Hz (3840x2160@30Hz SDR), 1080p
3D, CEC, and 7.1-channels of High Bit Rate (HBR) lossless digital audio such as
Dolby TrueHD, DTS-HD Master Audio.
• Zero signal compression and zero latency, supports point to point conguration,
and 2 to 1 conguration.
IMPORTANT NOTE: This 60GHz wireless extender is intended to be used in the same
room or area. To get the best transmission range both the transmitter and receiver
units must have full line of sight of each other. The 60GHz wireless signals will not pass
through walls, ceilings or oors.
To get the best performance and resolution, position the receiver and transmitter
where no xed or moving obstacles can interrupt the line of sight between the Wireless
transmitter and receiver.
OVERVIEW
FEATURES

3
Receiver
1. Power input Connect with PSU.
2. HDMI input Connect with HDMI source device.
3 Micro USB Connect to the source device USB port (optional).
4. Transmission LED Slow ash LED indicates the unit has started radio
transmission and has not yet found the receiver, transmitter
is in scan mode, searching for a matching receiver.
Fast ash LED indicates the transmitter and receiver have
been connected well with each other;
LED solid on means the transmitter and receiver have
established an audio or video connection, transmission in
operation.
5. Power LED Illuminates when the power is switched on.
6. Reset button Long press (>10 seconds): set to factory default
When the button is short pressed on the receiver if other
transmitter sources are available in its network, the receiver
will give up the change connection to the next available
source
Transmitter
1. Power input Connect with PSU.
2. HDMI input Connect with HDMI source device.
3 Micro USB Connect to the source device USB port (optional).
4. Transmission LED Slow ash LED indicates the unit has started radio
transmission and has not yet found the receiver, transmitter
is in scan mode, searching for a matching receiver.
Fast ash LED indicates the transmitter and receiver have
been connected well with each other;
LED solid on means the transmitter and receiver have
established an audio or video connection, transmission in
operation.
5. Power LED Illuminates when the power is switched on.
6. Reset button Restores the device to factory setting.

4
INSTALLATION
• Connect the transmitter HDMI input to the HDMI source device. Connect the
receiver HDMI output with HDMI display device.
• Connect the power supplies to both transmitter and receiver and plug into the mains
and turn on the power.
• Face the transmitter and receiver directly towards each other for maximum
transmission range and best picture and sound performance.
• In the event of a no picture or sound symptom rstly check that the correct HDMI
input is selected on the display device and also check/change the HDMI output
resolution on the source device, it must not be set to higher than 4K@30Hz. Also
verify that HDR (high Dynamic Range is turned off).
NOTE: If uninterrupted direct line of sight is not possible then transmission range can be
signicantly reduced, also local environmental factors may also affect the transmission
range and the best resolution. This also includes moving objects, people or animals
walking in front of the transmitter or receiver or electrical interference.
2. Two to one connection
1. Point to point connection

5
Voltage/Current DC 5V/1A
Power consumption TX: <2.5W RX: <2.5W
HDMI compliance HDMI 1.4
HDCP compliance HDCP 2.2
HDMI resolution 80i@60Hz, 480p@60Hz, 576i@50Hz. 576p@50Hz.
720p@50/60Hz. 1080i@50/60Hz. 1080p@50/60Hz
1080p@50/60Hz/120Hz, 3840x2160@24/30Hz
Audio formats supported CH 7.1/LPCM/DTS-HD/Dolby-AC3
Maximum transfer rate 10.2Gbps
Input and output TMDS
signal
0.7~1.2Vp-p(TMDS)
Input and output DDC
signal
5Vp-p(TTL)
Transmission method 60GHz wireless
Max Transmission range Line of sight operation only 4K 30Hz SDR 10m
Lower resolutions; range will be higher - max 30m
Latency Zero
Working temperature 0~40°C
Storage temperature -20~70°C
Humidity 0~90%RH (no condensation)
Dimension 79.8(W) x 45.7(D) x 54.0(H)mm
Material Alloy
Weight TX: 120g RX: 120g
SPECIFICATIONS
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical
& Electronic Equipment (WEEE). Any WEEE marked products must not be mixed with
general household waste, but kept separate for the treatment, recovery and recycling
of the materials used. Contact your local authority for details of recycling schemes in
your area.
Made in China. PR2 9PP
Man Rev 1.1
CLEANING & MAINTENANCE
Clean the outside casing with a soft cloth lightly moistened with mild soap and water.
Never use any abrasive or solvents.