PROAIM Explorer User manual

1
What’s In The
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
Assembly Manua l
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Explorer Pan Tilt Head for Camera Jib Crane
(PT-EXPR-01)
Pan Tilt Head
Controller Box 12V AC Adapter
2 x Fuse
4 x Washers
4 x Knobs
O-Ring
2 x Camera Bolts
(Sizes: 1/4”-20 , 3/8”-16)
15mtr Cable 3mtr Cable
4 x Bolts
(Sizes: 1/4”-1”)
4 x Bolts
(Sizes: 1/4”-3/4”) 4 x Bolts
(Sizes: 1/4”-5/8”)
Bolt
Universal
Adapter

2
3 x T-Type Allen Keys
(Sizes: 2.5mm, 4mm, 5mm)
2 x L-Type Allen keys
(Sizes: 2mm, 3/16”)
1 x Spanner (Size: 13)
Balancing Tips
• Before balancing the camera, Detach the
motor gear assembly from the head.
NOTE: You can only balance the camera on the
head aer detaching the motor gear; otherwise,
the motor will not funcon properly.
• Then mount your camera on the explorer
head's camera plate.
• Horizontally balance your camera by placing
the camera in the center of the camera plate.
• Aer that, vercally balance your camera by
loosening the side knob and increasing it to
the desired height, then ghten the knob
properly.

3
• Loosen the Pan Tilt Head’s Knob and increase
its height.
Explorer Pro Pan Tilt Head Setup
• Then properly ghten the knob, as shown in
the image.
• Connect the male end of the cable to the
female end of the Pan Tilt.
Connecons of Controller Box
NOTE: Proaim Explorer Pan-Tilt head is precisely engineered, easy to operate & a silent companion for
accurate panning & lng moons.
• The camera is now balanced both vercally
and horizontally.
• Now, reaach the motor gear to the head.
NOTE: Make sure that the camera is balanced in
all direcons depending on its weight so that
the motor can funcon properly when aached.

4
• Insert the 12-volt AC adapter (4 pin XLR) in the
controller box.
NOTE: If the Joysck Control is opposite, undo
the connectors of motors, rotate 180° and
re-install.
• Switch ON the controller box, as shown in the
image.
• Increase/decrease the Panning speed as per
your requirements and set the damping.
• Aach the second end of the power cable to
the universal adapter.
• Aach the Power cable to the AC adapter.
• Connect the female end of the cable to the
controller box.
NOTE: Any 12 volt baery may operate this Pan
Tilt Head as long as the Connector and the #1
Negave pin & #4 Posive pin of Cable meet
together.

5
• Insert both the knobs and ghten them
securely. Follow the same process to insert
knobs at the backside as well.
• Properly slide the Pan Tilt into the Jib Arm, as
shown in the image.
NOTE: This 2-Axis pan-lt head facilitates
eortless connuous 360° rotaon on both
horizontal and vercal axis that gives the
operator full freedom to capture any desired
angle.
• To change the direcon of Panning move the
joy-sck to the le and right. And to change
the direcon of the Tilt, move the joysck
back and forth/ up and down.
NOTE: Joysck remote controller provides a
great range of pan and lt speed control with
an excellent rotaon for a complete revoluon
in any axis.
Pan Tilt Setup
NOTE: Speed Controller -The Speed Controller
adjusts the speed of pan & lt based on the
requirement of the shot.
Damping Control -Damping control prevents
the Head from stopping with a jerk enabling
you to achieve smooth endings.
Pan-Tilt Direcon -You can reverse the panning
& lng direcon as & when required.