PROAIM P-G-PM User manual

1
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
Power Sucon Mount Camera Gripper (P-G-PM)
Assembly Manual
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
What’s In The Box
2 x Sucon Cups
2 x Ropes
2 x Ropes Hooks
Camera Mounng
Plaorm
3 x Bowl Head
100mm Bowl
Adapter
3 x Sucon Cups with Cap
9 x Aluminum Rods
(Size: 30cm,15cm,7.5cm)
2 x Camera Mounng Bolts
(Size: 2 x 1/4” & 3/8”)
1 x L-Type
Allen Key (Size:4mm)

2
Camera Mount Gripper Setup
 Remove the cap from the Sucon Cup, and
you will see 1/4” thread located in the center,
as shown in the image.
 Remove the dust cover and posion the
sucon cup wherever required.
 Screw in the Ball Tilt Head on suction cups.
Adjustable Ball Tilt Heads allow for an
extensive range of lockable positions for
Aluminum Rods.
 Pull and then remove the cap of the
aluminum rod (30cm).
 Similarly, mount all the Ball Tilt heads onto
the suction cups.
 Press down the sucon cup and keep pushing
the pump to rmly x it on the surface.
Repeat this process for all the sucon cups.
Cauon: Recheck the Pump every 90 minutes.
If the red line is visible, Re-pump the cup
without losing the remaining vacuum ll the
Red Line disappears.
3 x Dierent Aluminum Rods Assembly

3
 Screw the other end of the aluminum rod
(30cm) onto the Ball Tilt head, and then
tighten it.
 First loosen the knob, then set the posion of
the Aluminum rods and nally secure them by
ghtening the knobs.
 Screw the rods into the camera mounng
plaorm and ghten them.
 Firstly, remove the dust cover and place your
sucon cup on the selected place and press
down to x the pump rmly on the surface.
 Remove the cap of the aluminum rod (15cm),
then screw and tighten it properly onto the
Ball Tilt head. Repeat the same process for
attaching the other aluminum rods.
NOTE: Three rods are provided for each length
(30cm,15cm,7.5cm). These rods can be linked
together in any combinaon you need to create
the perfect setup.

4
 Aach one end of Rope with metal Hooks to
camera mounng plaorm and another end
to Metal loop of Sucon cup. Tighten the
Rope properly.
 Adjust the rope with the help of the push-pin
button of the hook, as shown in the image.
 Aach Rope Hooks to your vehicle, then
aach metal hooks to Rope Hooks and
ghten rope properly to secure your gripper.
 Mount the camera (Not Included) onto the
top mounting part of the setup, and then
properly tighten the knob at the bottom.
Bowl Adapter Setup
 Mount the Bowl Adapter onto the camera
platform, and then insert the bolt by aligning
the threads, as shown in the image.
 Rope hooks have been properly aached to
the sucon cups with metal hooks.

5
 Secure all the bolts using the Allen key.
 Remove the knob of the Bowl Fluid Head
(Not Included) and mount it on the Bowl
Adapter .
 Then, properly ghten and secure the knob of
the Fluid Head (Not Included) from the
boom.
 Aach the camera plate to the boom of the
camera (Not Included), then secure it with
the help of a screwdriver, as shown in the
image.
 Pull the knob of the uid head (Not Included),
then slide and mount the camera
(Not Included), as shown in the image.
 Loosen the uid head (Not Included) knob
and then remove the plate.

6
The Camera mounng plaorm of Power Mount Gripper has three leg aachment points that are each ed
with two posive locking ratchet joints, one for lt and one for swivel. Each locking ratchet joint has a quick
turn knurled lock ring for easy adjustment. You can unlock and lock each joint with a slight twist.
To adjust lt or swivel of each leg, rst make sure lock ring on the appropriate joint is in the UNLOCK
posion, then adjust posion of the leg as per need. And then turn lock ring back in the LOCK direcon so
that the camera won’t shake from joint movement while the vehicle is in moon.
Swivel Adjustments
Tilt Adjustments
Features of Camera Mounng Plaorm

7
YOUR PROAIM POWER SUCTION MOUNT CAMERA GRIPPER
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon and
evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.