PROAIM P-18-JS User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Central Post
Weight Rod / Shank
Weight Closers
LCD Mounng Arm
Tools
1st Secon
2nd Secon
3rd Secon
4th Secon
5th Secon
18 Film Crane with Jib Stand (P-18-JS)
Assembly Manua l
Jib Stand
Power Pack

2
Jib Stand Setup
 Loosen knob-1 located on Jib Stand. Slide the legs down to the widest possible posion and ghten
knob-1 to secure.
NOTE: A wider spread ensures more stability.
 Slide Central Post of Jib onto the Jib Stand and ghten knob-2 to secure it.
 Open shank from central post. Leave the black washers at one side. Then insert the end of Secon-3
inside Central Post. Align holes of Secon with Central Post to screw in the shank back.
 Similarly, insert black washers onto other side and push the shank to ghten it with the dome nut.
 Using a wrench, ghten the dome nut from both sides to secure them.
Locking Pin
 Draw Central Post up to the desired height and lock it into place using provided Locking Pin.
Camera Jib Setup
Knob 2
Knob 1

3
 Secon-4 has connecng bars aached on both ends. Slide bars of Secon-4 into Secon-3 & ghten
them together using provided allen key. Connue the Arm build by sliding in secon 2 onto secon 3,
secon 2 onto secon 1 and nally secon 5 onto secon 4 in the same way. Your jib arm is now com-
pletely connected.
 Tighten the Wire Puller and its Central Pool Adapter. Tighten bolts to secure them.
 Connect the Wire/Cable Tensioner with cable.
Simply rotate the mid-secon handle to ghten
the cable adding required amount of strength to
the system.
Tighten Bolts
Connecng Bar
NOTE: Once you discover correct balance, consider marking the weights for that parcular camera;
facilitang an easier set up the next me.
 To accommodate all standard cameras, mulple
slots are provided for aachment on Camera
Plate.
 Insert Weight Shank/Rod and standard exercise
Weights (Not Included) with a 1” hole, according
to your camera setup requirements. Secure them
with Weight Closers.

4
 You can easily mount any Pan Tilt Head
(Not Included) on the provided slots on camera
plate via screws. This assembly is accomplished
in Under slung Mode.
 Removing Locking Pin from Central Post allows
you to frame mul-dimensional lng shots by
using Control Handle.
 The Central Fork has provision to aach LCD
Monitor (Not Included) via LCD Mounng Arm.
YOUR PROAIM 18FT JIB ARM WITH STAND
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)

5
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.