PROAIM P-WV-2PP User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
7' Wave-2 Camera Jib Crane, Pan Tilt, Dolly
Stand Gimbal Compable (P-WV-2PP)
Assem b l y M a n u a l
Proaim Lanc Zoom Controller
Speed Controller
Portable Dolly with
CST-100mm Bowl
Tripod stand
Aluminum Spreader
Jr Pan-Tilt
Head
Allen key
Wave-2 jib Crane
Telescopic Knob
Flat Base Plate
100 mm Bowl
75mm Conversion
Ring
Weight Bar
and Closer

2
Take out the bolt from the center of dolly and
spread it on oor. Then put the bolt back
through the center of dolly again.
Posion the height of the tripod by loosening
all three adjustment knobs, slide the tripod
up to the desired height and re-ghten the
knobs securely.
Now, place the tripod foot on the dolly and
e it down with the help of elasc clips as
shown in the picture.
Camera Jib Crane Setup
ASSEMBLING YOUR PROAIM 7' WAVE -2 JIB WITH CST-100STAND, PORTABLE DOLLY
& JR. PAN TILT HEAD
IN CASE OF ALUMINUM TRIPOD SPREADER, FOLLOW THESE STEPS
In case of spreader, Take out the Spreader
and spread it on floor and open the legs (as
per your requirement) of spreader with the
help of provided knob.
Storage Bags

3
Unscrew the locking lever from the Central
Post of the jib. Place the Central Post in the
bowl of Tripod Stand and re-ghten the
locking mechanism for a secure t. (as shown
in the picture.)
Provided are the jib panning control knobs (as
shown in the picture). Loosen the knobs for
the smooth pan movement of the jib and
ghten these knobs to lock the pan move-
ment of the jib.
NOTE: Inbuilt bubble leveler is also
provided to check accurate set-up of jib on
uneven surface areas.
Now to extend the rear secon of the jib,
loosen the Allen bolts with the provided Allen
key and then, loosen the knob as shown in
the picture.
Now mount the Tripod Stand on Spreader,
lock it in place with the rubber grips
MOUNTING THE JIB
NOTE: It is important to make sure that the Central Fork is seated in the bowl properly. That means
perpendicular to the tripod bowl. O axis installaon may hamper movement of the jib. Also you may need
the assistance of a grip stand to hold the camera end of the arm during installaon prevenng it from fall-
ing as it will be front heavy at this point. You may also need the grip stand or assistance at the rear of the
jib when mounng the camera.
Then, loosen the knob provided at the lower
telescopic secon of the jib arm as shown in
the picture to extend the front secon of the
telescopic jib accordingly to the rear secon.

4
Aach the weight shanks at the rear end of
the jib secon by screwing it in and then add
weights to it.
NOTE: Make sure the opposite end of the jib
arm is secured so that the addion of the
weights does not cause the arm to rise violently.
Camera head mount is provided with a knob
to control 90 degree lt movement of the
camera.
Loosen the knob for the free lt movement of
the camera and ghten it to lock the
movement.
Remove the fluid head mounting bowl by
loosening the bolts as shown and then remove
the 100mm bowl.
Mount your uid head onto the bowl plate in
order to aach the camera. And then nally,
secure your camera properly on the uid
Head.
To mount Jr. Pan Tilt Head, follow these steps:
Attach the flate base plate and secure by
tightening the bolts and then attach the Pan
Tilt Head and secure by tightening the bolts.
Now, mount your camera with camera
mounng screw on Pan Tilt Head.

5
Mount the Joysck on weight rod & ghten
the knob to secure.
Now aach the one end of XLR Cable & AC
Adapter with Joysck. And second end of XLR
cable with Pan Tilt Head.
Aach the LCD Mounng Arm to Jib Fork and
ghten it properly to secure.
Now screw in the LCD to arm and ghten it
knob aer posioning the angle of LCD Arm.
LCD Mounng
•For an over slung setup, attach the flat base
plate on the top and mount the camera
setup and secure the camera properly.
For 100mm fluid head setup mounting,
attach the 100mm bowl on the top, mount
the camera setup and secure it properly.
•

7
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.
YOUR 7' WAVE-2 CAMERA JIB CRANE, PAN TILT, DOLLY STAND GIMBLE COMPATIBLE
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)