ProLights EclMini CC User manual

USER MANUAL
REV.01-10/22 English version
EclMini CC
18W White LED gallery light, constant cur-
rent. Connects to an external PSU and driver

Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements
for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be
a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively
applicable national accident prevention rules and regulations.
Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other
loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial
PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).
Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad
set of always updated technical documentation: specications, user manual, technical drawings, photometrics,
personalities, xture rmware updates.
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services
or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.
PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc -
04026 - Minturno (LT) ITALY
Visit the download area
of the product page

PROLIGHTS - EclMini CC 01
INDEX
SAFETY INFORMATION 02
1 - PACKAGING 05
PACKAGE CONTENT..................................................................................................... 05
2 - OPTIONAL ACCESSORIES 05
DEDICATED ACCESSORIES........................................................................................... 05
NORDIC ALUMINUM TRACK......................................................................................... 05
3 - TECHNICAL DRAWING 06
4 - TILT RANGE 07
5 - INSTALLATION 08
MOUNTING.................................................................................................................... 08
6 - CONNECTION TO THE EXTERNAL PSU OR LED DRIVER 09
7 - CONNECTION TO EXTERNAL POWER SUPPLIES 10
8 - START UP 11
CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 11
9 - PRODUCT OVERVIEW 11
10 - ACCESSORIES INSTALLATION 12
OPTIC (CODES ECLDISPWASHL1530 / ECLDISPWASHL2550 / MINIECLL / MINIECLTRL
- OPTIONAL)................................................................................................................... 12
BARNDOOR AND FILTER FRAME (CODE ECLMINIBDNFF - OPTIONAL) .................... 13
ANTI-GLARE LOUVRE (CODE ECLMINILOUVRE - OPTIONAL)..................................... 14
HALF SNOOT, FULL SNOOT (CODES ECLMINIHSNOOT, ECLMINIFSNOOT -
OPTIONAL)..................................................................................................................... 15
11 - MAINTENANCE 16
MAINTENANCE AND CLEANING THE PRODUCT........................................................ 16
VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 16
TROUBLESHOOTING..................................................................................................... 17

PROLIGHTS - EclMini CC02
SAFETY INFORMATION
WARNING!
• Please read carefully the instruction reported in this section before installing, power-
ing, operating or servicing the product and observe the indications also for its future
handling.
This unit is not for household and residential use, only professional applications.
Connection to mains supply
• The Connection to the mains supply must be carried out by a qualied electrical
installer.
• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected
to ground (earth).
• Select the cable cross section in according with the maximum current draw of the
product and the possible number of products connected at the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual
current circuit breaker protection.
• Do not connect it to a dimmer system; doing so may damage the product.
Protection and Warning against electrical shock
• Do not remove any cover from the product, always disconnect the product from AC
power before servicing.
• Ensure that the xture is electrically connected to ground (earth). And use only a
source of AC power that complies with local building and electrical codes and has
both overload and ground-fault (earth-fault) protection.
• Before using the xture, check that all power distribution equipment and cables are
in perfect condition and rated for the current requirements of all connected devices.
• Isolate the xture from power immediately if the power plug or any seal, cover, ca-
ble, or other components are damaged, defective, deformed or showing signs of
overheating.
• Do not reapply power until repairs have been completed.
• Refer any service operation not described in this manual to PROLIGHTS Service team
or an authorized PROLIGHTS service center.
Installation
• Make sure that all visible parts of the product are in good visible condition before its
use or installation.
• Make sure the point of anchorage is stable before positioning the projector.
• When suspending the xture above ground level, secure it against failure of primary
attachments by attaching a safety cable that is approved as a safety attachment for
the weight of the xture to the attachment point on the main frame of the product. ln
case the safety cable, enter in action, it needs to be replaced with a new one.
• Install the product only in well ventilated places.
• For non temporary installations, ensure that the xture is securely fastened to a load-
bearing surface with suitable corrosionresistant hardware.
• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or
screws are turned fully, and secured with a suitable safety cable.
0.5 m Minimum distance of illuminated objects
• The projector needs to be positioned so that the objects hit by the beam of light are
at least 0,5 meters (1,64 ft) from the lens of the projector.

PROLIGHTS - EclMini CC 03
T 45°C
a
Max operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).
T
-10°
C
a
Minimum operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) is below -10 °C (14 °F).
Protection from burns and re
• The exterior of the xture becomes hot during use. Avoid contact by persons and
materials.
• Ensure that there is free and unobstructed airow around the xture.
• Keep ammable materials well away from the xture
• Do not expose the front glass to sunlight or any other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.
• Do not attempt to bypass thermostatic switches or fuses.
Indoor use
• This product is designed for indoor and dry environments.
• Do not use in wet location and do not expose the xture to rain or moisture.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture.
• Damages caused by inadequate cleaning or maintenance are not covered by the
product warranty.
T
65°
C
c
Temperature of the external surface
• The surface of the xture can reach up to 65 °C (149 °F) during operation. Avoid
contact with people and materials.
Maintenance
• Warning! Disconnect the xture from AC mains power and allow to cool for at least
10 minutes before handling.
• Only technicians who are authorized by PROLIGHTS or Authorised service partners
are permitted to open the xture.
• Users may carry out external cleaning, following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred to a
qualied service technician.
• Important! Excessive dust, smoke uid, and particle build up degrades performance,
causes overheating and will damage the xture. Damages caused by inadequate
cleaning or maintenance is not covered by the product warranty.
Photobiological safety
• This device emits potentially dangerous optical radiation and is identied in the cat-
egory of Risk Group 2 according to EN 62471.
Do not stare at the operating light source
• Do not look directly at the LED source during operation. It can be harmful to the eyes
and skin.
• During Installation, operation and maintenance, be prepared for the xture to light
and move suddenly when connected to power.
• The device should be positioned so that prolonged staring into the luminaire at adis-
tance closer than 2,384 m (7,821 ft) is not expected.

PROLIGHTS - EclMini CC04
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
10.5 m
34.45 ft
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
10.5 m
34.45 ft
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
2,384 m
7,821 ft
Disposal
• This product is supplied in compliance with European Directive 2012/19/EU – Waste
Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-
pose/ recycle this product at the end of its life according to the local regulation.
The products to which this manual refers comply with:
• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).
• 2014/30/EU - Electromagnetic Compatibility (EMC).
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).
The products to which this manual refers comply with:
• UL 1573 + CSA C22.2 No. 166 - Stage and Studio Luminaires and Connector Strips.
• UL 8750 + CSA C22.2 No.250 13-20 / Clause - Standard for power units other than class 2.
FCC Compliance:
• This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
Other approvals
• The product meets the safety requirements of the certification procedures of the
market in which it is placed and sold.

PROLIGHTS - EclMini CC 05
1 - PACKAGING
PACKAGE CONTENT
• 1x MINIECLCC.
• User Manual.
2 - OPTIONAL ACCESSORIES
DEDICATED ACCESSORIES
• RSR0630A/B: steel security cable for hanging bodies, inox steel shackle, L=60 cm, silver/black.
• C6002A/B: slim aluminum clamp, 200kg loading, 48-51mm tubes, M10 bolt, silver/black.
• ECLMINIWASHL1530B/W: zoomable Wash Lens 15-30° for EclMini, white/black.
• ECLMINIWASHL2550B/W: zoomable Wash Lens 25-50° for EclMini, white/black.
• MINIECLL19: optics for MINIECL proler, gobo holder included, 19° beam.
• MINIECLL26: optics for MINIECL proler, gobo holder included, 26° beam.
• MINIECLL36: MINIECL proler, gobo holder included, 36° beam.
• MINIECLL50: optics for MINIECL proler, gobo holder included, 50° beam.
• MINIECLTRL19: optics for MINIECLTR proler, gobo holder included, 19° beam.
• MINIECLTRL26: optics for MINIECLTR proler, gobo holder included, 26° beam.
• MINIECLTRL36: optics for MINIECLTR proler, gobo holder included, 36° beam.
• MINIECLTRL50: optics for MINIECLTR proler, gobo holder included, 50° beam.
• ECLMINIHSNOOTB/W: half Snoot for EclMini, white/black.
• ECLMINIFSNOOTB/W: full Snoot for EclMini, white/black.
• ECLMINILOUVREB/W: anti-glare louvre for EclMini, white/black.
• ECLMINIBDNFFB/W: barndoor and lter frame (compatible with Wash Lenses) for EclMini, white/black.
• PLCLD82075: LED Driver PVC cable black 2x0,75 mmq D=6,5mm (BLACK-RED), 1 meter lenght.
• ELTOOLBOXPRO: TOOLbox pro.
• ELECODRIVE360A: ECOdrive, 30W, DALI-2, Pulse dimming, 1 control channel, con. cur., 1x55V output.
NORDIC ALUMINUM TRACK
NOTE: the nal terms "2" and "3" in the codes indicate the corresponding color variant in black and
white respectively.
• NAXTSC61002/3: global Pulse XTSC Lighting Track, 3 circuit DALI, 1000mm, white/black.
• NAXTSC62002/3: global Pulse XTSC Lighting Track, 3 circuit DALI, 2000mm, white/black.
• NAXTSC63002/3: global Pulse XTSC Lighting Track, 3 circuit DALI, 3000mm, white/black.
• NAXTSC64002/3: global Pulse XTSC Lighting Track, 3 circuit DALI, 4000mm, white/black.
• NAXTSC6112/3: global Pulse XTS Connector 3-CCT DALI end feed, earth right, white/black.
• NAXTSC6122/3: global Pulse XTS Connector 3-CCT DALI end feed, earth left, white/black.
• NAXTSC6142/3: global Pulse XTS Connector 3-CCT DALI middle feed, white/black.
• NAXTSC6212/3: global Pulse XTS Connector 3-CCT DALI straight connector, white/black.
• NAXTSC6232/3: global Pulse XTS Connector 3-CCT DALI exible corner connector, white/black.
• NAXTSNC6342/3: global Pulse XTSN Connector 3-CCT DALI L connector, earth right, white/black.
• NAXTSNC6352/3: global Pulse XTSN Connector 3-CCT DALI L connector, earth left, white/black.
• NAXTSNC6362/3: global Pulse XTSN Connector 3-CCT DALI T connector, earth right/right, white/black.
• NAXTSNC6372/3: global Pulse XTSN Connector 3-CCT DALI T connector, earth left/left, white/black.
• NAXTSNC6382/3: global Pulse XTSN Connector 3-CCT DALI X connector, white/black.
• NAXTSNC6392/3: global Pulse XTSN Connector 3-CCT DALI T connector, earth right/left, white/black.
• NAXTSNC6402/3: global Pulse XTSN Connector 3-CCT DALI T connector, earth left/right, white/black.
• NAXTS412/3: global Pulse XTS Connector 3-CCT DALI END cap, white/black.
• NAXTSA682/3: global Pulse 3-Circuit MULTI Adapter, 10A 100N Slot connection, white/black.
• NAGA0172/3: global Pulse 3-Circuit Adapter-Driver, 200-700mA, 8,8-31W, white/black.
• NAGAC6162/3: global Pulse DALI 3-Circuit Adapter-Drivers, 300-1050mA, 12,6-40W, white/black.
• NAGAW0162/3: global Pulse CASAMBI 3-Circuit Adapter-Drivers, white/black.
• NASPW12SK215M: global Pulse Track clip wire suspension set 1.5m, 150N, black.
• NASPW12SK25M: global Pulse Track clip wire suspension set 5m, 150N, black.
• NASPW12SK315M: global Pulse Track clip wire suspension set 1.5m, 150N, white.
• NASPW12SK35M: global Pulse Track clip wire suspension set 5m, 150N, white.
• NAXTSA57129: global Pulse Rotating Nipples 3-Circuit Adapters, M10, H 12mm, D 7,4mm.
• NAXTSA55129: global Pulse Rotating Nipples 3-Circuit Adapters, M13, H 12mm, D 9mm.
• NAGAM109: global Pulse Nut M10 for NAXTSA57129.
• NAGAM139: global Pulse Nut M13 for NAXTSA55129.
• NASKB12/3: global Pulse Track Mounting Clamp for Rod and Wire, 200N, white/black.

PROLIGHTS - EclMini CC06
3 - TECHNICAL DRAWING
Weight: 1,61 kg - 3,55 lbs ECLMINICC with ECLDISPWASHL1530
Weight: 1,6 kg - 3,53 lbs ECLMINICC with ECLDISPWASHL2550
182 mm
[7.2 in]
146 mm
[5.7 in]
224 mm
[8.8 in]
Ø63 mm
[2.5 in]
291 mm
[11.5 in]
92 mm
[3.6 in]
Weight: 1,78 kg - 3,92 lbs ECLMINICC with MINIECLL
Fig. 01

PROLIGHTS - EclMini CC 07
4 - TILT RANGE
60°
256°
TILR RANGE: 196°
Fig. 02

PROLIGHTS - EclMini CC08
5 - INSTALLATION
MOUNTING
Check that the supporting structure can safely bear the weight of all installed xtures, clamps, cables,
auxiliary equipment, etc. and complies with locally applicable regulations.
When suspending the xture above ground level, secure it against failure of primary attachments by
attaching a safety wire that is approved as a safety attachment for the weight of the xture to an anchor
point on the product main frame.
Do not use removable parts or weak anchors for secondary attachment.
Warning! When clamping the xture to a truss or other structure at any angle, use clamps of half-cou-
pler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
Fig. 03
C6002
clamp
RSR0630A/B
Steel security cable
26 mm
1,02 in
58 mm
2,3 in
Ø13,2 mm
Ø0,51 in
24,59 mm
0,96 in
24,59 mm
0,96 in
Track system

PROLIGHTS - EclMini CC 09
6 - CONNECTION TO THE EXTERNAL PSU OR LED DRIVER
Use only SELV remote control gear (max output voltage 60V). The unit must be powered only by Con-
stant Current PSU. To avoid damage, do not connect the unit to any Constant Voltage PSU. Installation
must be performed by a qualied person.
• ECLMINICC: max current 500mA 36V 18W.
Led driver: constant current 500mA maximum output voltage 60Vdc, min 18W.
NOTE: Please take attention to the polarity of the connection.
1
Loosen and remove the marked four screws. Then remove the arm housing (1).
Fig. 04

PROLIGHTS - EclMini CC10
CONNECTION WIRES
LED - BLACK
LED + RED
LED
driver
MAINS
CONTROL
SIGNAL
Fig. 05
7 - CONNECTION TO EXTERNAL POWER SUPPLIES

PROLIGHTS - EclMini CC 11
Fig. 06
1
5
2
3
4
6
3
2
7
8 - START UP
CONNECT AND DISCONNECT POWER FROM THE PRODUCT
To apply and disconnect power to the product:
• Check that the product is installed and secured as indicated in the Safety Informations, and that
personal safety will not be put at risk when the xture lights up.
• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).
• The product is then ready for its operations and can be controlled through the available input sig-
nals on board.
• To disconnect power from the product, disconnect the Mains from the socket.
9 - PRODUCT OVERVIEW
1. SAFETY EYE to attach safety cable.
2. KNOB for releasing and locking the optic.
3. KNOB for releasing and locking the optic and for zoom.
4. OPTIC (accessory not included, in the gure ECLDISPWASHL1530).
5. RUBBER RING (accessory included in the optic box).
6. PLASTIC CAP for access to connections.
7. LOCK TILT.

PROLIGHTS - EclMini CC12
10 - ACCESSORIES INSTALLATION
OPTIC (CODES ECLDISPWASHL1530 / ECLDISPWASHL2550 / MINIECLL / MINIECLTRL - OPTIONAL)
NOTE: the mounting procedure described below is the same for all lenses.
1
A
C
B
Loosen the two marked knob (A) of the ECLMINICC.
23
A
A
Insert the optic (1-B) and rotate it (1-C) so the marked grooves (2-D) of the optic coincides with the
four marked aps of the unit (3-A).
Fig. 07

PROLIGHTS - EclMini CC 13
1 2
3
Insert the lter frame mounting the four marked
screws into the holes provided on the optic.
Rotate the marked knob of the lter frame (2) and
and move the marked rod upwards (3).
4 6
5
Insert the holder from above throught the track
(4). Then insert the barn door (5).
Move the marked rod down (6).
Fig. 08
BARNDOOR AND FILTER FRAME (CODE ECLMINIBDNFF - OPTIONAL)

PROLIGHTS - EclMini CC14
ANTI-GLARE LOUVRE (CODE ECLMINILOUVRE - OPTIONAL)
NOTE: the rubber ring can also be used to x a lter with a maximum diameter of 79 mm.
1
Rubber ring
Anti-glare louvre
Insert the anti-glare louvre or a lter of maximum size of Ø50 mm into the rubber ring.
2
Mount the anti-glare louvre with the rubber ring on the optic.
Fig. 09

PROLIGHTS - EclMini CC 15
HALF SNOOT, FULL SNOOT (CODES ECLMINIHSNOOT, ECLMINIFSNOOT - OPTIONAL)
1
Loosen the three marked knob. Insert the half snoot on the optic and tighten the knobs in the egraved ring.
2
Loosen the three marked knob. Insert the full snoot on the optic and tighten the knobs in the egraved ring.
Fig. 10

PROLIGHTS - EclMini CC16
11 - MAINTENANCE
MAINTENANCE AND CLEANING THE PRODUCT
WARNING: Disconnect from the mains before starting any maintenance work
It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or
other particles to ensure that the light is radiated at maximum brightness.
• For cleaning, disconnect the main plug from the socket. Use a soft, clean cloth moistened with a
mild detergent. Then carefully wipe the part dry. For cleaning other housing parts use only a soft,
clean cloth. Never use a liquid, it might penetrate the unit and cause damage to it.
• The user must clean the product periodically to maintain optimum performance and cooling. The
user may also upload rmware (product software) to the xture via the DMX signal input port or USB
port using rmware and instructions from PROLIGHTS.
• The frequency of such maintenance operations is to be performed according to various factors, such
as the amount of the use and the condition of the installation environment (air humidity, presence
of dust, salinity, etc.). It is recommended that the product is subject to annual service by a qualied
technician for special maintenance involving at least the following procedures:
• General cleaning of internal parts.
• For all the parts subject to friction, using lubricants specically supplied by PROLIGHTS.
• General visual check of the internal components, cabling, mechanical parts, etc.
• Electrical, photometric and functional checks; eventual repairs.
• Cleaning the lenses. Only use neutral soap and water to clean the lenses, then dry it carefully with
a soft, non-abrasive cloth.
WARNING: the use of alcohol or any other detergent could damage the lenses.
• All other service operations on the product must be carried out by PROLIGHTS, its approved service
agents or trained and qualied personnel.
• It is PROLIGHTS policy to apply the strictest possible calibration procedures and use the best quality
materials available to ensure optimum performance and the longest possible component lifetimes.
However, optical components are subject to wear and tear over the life of the product, resulting
in gradual changes in colours over many thousands of hours of use. The extent of wear and tear
depends heavily on operating conditions and environment, so it is impossible to specify precisely
whether and to what extent performance will be affected. However, you may eventually need to re-
place optical components if their characteristics are affected by wear and tear after an extended pe-
riod of use and if you require xtures to perform within very precise optical and colour parameters.
• Do not apply lters, lenses or other materials on lenses or other optical components. Use only ac-
cessories approved by PROLIGHTS.
VISUAL CHECK OF PRODUCT HOUSING
• The parts of the product cover/housing should be checked for eventual damages and breaking
start at least every two months. In addition, especially the parts of the front lens holder have to be
checked mechanically (by means of movement by the part) if it is rmly fastened to the xture. If
hint of a crack is found on some plastic part, do not use the product until the damaged part will be
replaced.
• Cracks or another damages of the cover/housing parts can be caused by the product transportation
or manipulation and also ageing process may inuence materials.
• This checking is necessary for both xed installations and preparing product for renting. Any free
moving parts inside of the product, cracked cover/housing or any part of front lens not sitting prop-
erly in place need to be immediately replaced.

PROLIGHTS - EclMini CC 17
Problems Possible causes Checks and remedies
Product doesn’t power ON • No power to the
product
• Check that power is switched ON and cables are
plugged in.
Product reset correctly but
does not respond correctly
to the contoller.
• Bad signal connection • Inspect connections and cables. Fix eventual bad
connections. Repair or replace damaged cables.
• Signal connection not
terminated
• Insert DMX termination plug in signal output socket of
the last product on the signal line.
• Incorrect addressing of
the product
• Check the product address and control settings
• One of the product is
defective and is corrupt-
ing the signal transmis-
sion on the signal line
• Unplug the XLR in and out connectors and connect
them directly together to bypass one product at a
time until normal operation is regained. Once found
the error, have that xture serviced by a qualied
technician.
Timeout error after xture
reset.
• One or more hardware
• components requires
• mechanical adjustments
• Check product stored error messages for more
information. Contact PROLIGHTS Service or an
authorized service partner.
Mechanical effect loses
position
• Mechanical hardware
require cleaning, adjust-
ment or lubrication
• Check product stored error messages for more
information. Contact PROLIGHTS Service or an
authorized service partner.
Light output turn OFF
Intermittently
• Fixture is too hot • Check product stored error messages.
• Allow product to cool.
• Clean the product and airow lters.
• Reduce ambient temperature.
• Hardware failure (tem-
perature sensor, fans,
Light source...)
• Check product stored error messages for more
information. Contact. PROLIGHTS Service or an
authorized service partner.
General low light intensity • Dirty lens assembly
• Dirty or damaged lters
• Clean the xture regularly.
• Install lens assembly properly.
Contact an authorized service center in case of technical problems or not reported in the table can not
be resolved by the procedure given in the table.
TROUBLESHOOTING

Note