ProSoft Technology MVI56E-61850S User manual

MVI56E-61850S
ControlLogix Platform
IEC 61850 Server Communication
Module
September 3, 2014
USER MANUAL

Your Feedback Please
We always want you to feel that you made the right decision to use our products. If you have suggestions, comments,
compliments or complaints about our products, documentation, or support, please write or call us.
ProSoft Technology
5201 Truxtun Ave., 3rd Floor
Bakersfield, CA 93309
[phone]
[phone] (Fax)
www.prosoft-technology.com
[email protected]
© 2014 ProSoft Technology, Inc. All rights reserved.
MVI56E-61850S User Manual
September 3, 2014
ProSoft Technology®, is a registered copyright of ProSoft Technology, Inc. All other brand or product names are or
may be trademarks of, and are used to identify products and services of, their respective owners.
In an effort to conserve paper, ProSoft Technology no longer includes printed manuals with our product shipments.
User Manuals, Datasheets, Sample Ladder Files, and Configuration Files are provided on the enclosed DVD and are
available at no charge from our web site: http://www.prosoft-technology.com
Content Disclaimer
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of
these products for specific user applications. It is the duty of any such user or integrator to perform the appropriate
and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or
use thereof. Neither ProSoft Technology nor any of its affiliates or subsidiaries shall be responsible or liable for
misuse of the information contained herein. Information in this document including illustrations, specifications and
dimensions may contain technical inaccuracies or typographical errors. ProSoft Technology makes no warranty or
representation as to its accuracy and assumes no liability for and reserves the right to correct such inaccuracies or
errors at any time without notice. If you have any suggestions for improvements or amendments or have found errors
in this publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic or mechanical, including
photocopying, without express written permission of ProSoft Technology. All pertinent state, regional, and local safety
regulations must be observed when installing and using this product. For reasons of safety and to help ensure
compliance with documented system data, only the manufacturer should perform repairs to components. When
devices are used for applications with technical safety requirements, the relevant instructions must be followed.
Failure to use ProSoft Technology software or approved software with our hardware products may result in injury,
harm, or improper operating results. Failure to observe this information can result in injury or equipment damage.
© 2014 ProSoft Technology. All Rights Reserved.
Printed documentation is available for purchase. Contact ProSoft Technology for pricing and availability.
North America: [phone]
Asia Pacific: +603.7724.2080
Europe, Middle East, Africa: +33 (0) 5.3436.87.20
Latin America: +1.281.298.9109

Agency Approvals and Certifications
Agency
RoHS
ATEX
CSA
CE
CSA CB Safety
cULus
GOST-R
Important Safety Information
North America Warnings
A Warning - Explosion Hazard - Substitution of components may impair suitability for Class I, Division 2.
B Warning - Explosion Hazard - When in Hazardous Locations, turn off power before replacing or rewiring
modules.
C Warning - Explosion Hazard - Do not disconnect equipment unless power has been switched off or the area is
known to be nonhazardous.
D Suitable for use in Class I, Division 2 Groups A, B, C, and D, Hazardous Locations or Non-Hazardous Locations.
ATEX/IECEx Warnings and Conditions of Safe Usage:
Power, Input, and Output (I/O) wiring must be in accordance with the authority having jurisdiction
A Warning - Explosion Hazard - When in hazardous locations, turn off power before replacing or wiring modules.
B Warning - Explosion Hazard - Do not disconnect equipment unless power has been switched off or the area is
known to be non-hazardous.
C These products are intended to be mounted in an ATEX/IECEx Certified, tool-secured, IP54 enclosure. The devices
40%. This device must be used only with ATEX certified backplanes.
DBefore operating the reset switch, be sure the area is known to be non-hazardous.
shall provide external means to prevent the rated voltage being exceeded by transient disturbances of more than
<Ex>
II 3 G
Ex nA IIC T4 Gc
0°C <= Ta <= 60°C
-25°C <= Ta <= 70°C (XT models only)
II – Equipment intended for above ground use (not for use in mines).
3 – Category 3 equipment, investigated for normal operation only.
G – Equipment protected against explosive gasses. <cULus>
E183151
Class I, DIV 2, groups A,B,C,D
T5 for all models
0°C to +60°C
-25°C to +70°C (XT models only)

MVI56E-61850S ♦ ControlLogix Platform Contents
IEC 61850 Server Communication Module User Manual
ProSoft Technology, Inc. Page 5 of 81
September 4, 2014
Contents
Your Feedback Please........................................................................................................................2
Content Disclaimer..............................................................................................................................2
Important Safety Information...............................................................................................................3
1Start Here 7
1.1 System Requirements...............................................................................................8
1.2 Package Contents.....................................................................................................9
1.3 Setting Jumpers ........................................................................................................9
1.4 Installing the Module in the Rack ............................................................................10
1.5 Connecting Your PC to the ControlLogix Processor...............................................12
1.6 Downloading the Sample Program to the Processor..............................................13
1.6.1 Configuring the RSLinx Driver for the PC COM Port ..............................................14
2Setting Up ProSoft Configuration Builder 17
2.1 Installing ProSoft Configuration Builder ..................................................................17
2.2 Setting Up the Project .............................................................................................18
3MVI56E-61850S Configuration 21
3.1 Backplane Configuration.........................................................................................22
3.2 Ethernet1.................................................................................................................23
3.3 61850S Identification...............................................................................................24
3.4 61850S Network......................................................................................................25
3.5 61850S IP Filter.......................................................................................................26
3.6 61850S Data DB Configuration...............................................................................28
3.7 61850S Data SoE....................................................................................................30
3.8 61850S Data Control...............................................................................................32
3.9 61850S Buffered Reports........................................................................................34
3.9.1 61850S BR0x Dataset.............................................................................................36
3.10 61850S Unbuffered Reports ...................................................................................38
3.10.1 61850S UR0x Dataset.............................................................................................40
3.11 Downloading the Project to the Module ..................................................................42
3.11.1 Connecting Your PC to the Module's Ethernet Port................................................44
4RSLogix 5000 Configuration 49
4.1 MVI56E-61850S User-Defined Data Types............................................................49
4.2 MVI56E-61850S Controller Tags ............................................................................49
4.2.1 61850S Controller Tag Overview............................................................................49
4.2.2 MVI56E61850S.DATA.............................................................................................50
4.2.3 MVI56E61850S.COMMAND...................................................................................51
4.2.4 MVI56E61850S.STATUS Tag.................................................................................52
4.2.5 MVI56E61850S.UTIL Tag.......................................................................................52

Contents MVI56E-61850S ♦ ControlLogix Platform
User Manual IEC 61850 Server Communication Module
Page 6 of 81 ProSoft Technology, Inc.
September 4, 2014
5Examples 53
5.1 Data DB Example ................................................................................................... 53
5.2 SoE Example.......................................................................................................... 58
5.3 Control Example ..................................................................................................... 62
6Diagnostics and Troubleshooting 65
6.1 Ethernet LED Indicators.......................................................................................... 65
6.1.1 Scrolling LED Status Indicators.............................................................................. 66
6.1.2 Non-Scrolling LED Status Indicators ...................................................................... 67
6.2 Clearing a Fault Condition ...................................................................................... 67
6.3 Troubleshooting...................................................................................................... 68
6.4 Using the Diagnostics Menu in ProSoft Configuration Builder ............................... 69
6.4.1 Monitoring Module Information............................................................................... 72
6.4.2 Monitoring Backplane Information.......................................................................... 73
6.4.3 Monitoring Base Configuration Information............................................................ 74
6.4.4 Monitoring Data Mappings Information................................................................... 75
6.4.5 Monitoring Backplane Information.......................................................................... 76
6.4.6 Monitoring Flat Database Information .................................................................... 77
6.5 Connect to the Module’s Web Page ....................................................................... 78
7Support, Service & Warranty 79
7.1 Contacting Technical Support................................................................................. 79
7.2 Warranty Information .............................................................................................. 80
Index 81

MVI56E-61850S ♦ ControlLogix Platform Contents
IEC 61850 Server Communication Module User Manual
ProSoft Technology, Inc. Page 7 of 81
September 4, 2014
1 Start Here
In This Chapter
System Requirements............................................................................. 8
Package Contents .................................................................................. 9
Setting Jumpers...................................................................................... 9
Installing the Module in the Rack...........................................................10
Connecting Your PC to the ControlLogix Processor..............................12
Downloading the Sample Program to the Processor.............................13
To get the most benefit from this User Manual, you should have the following skills:
Rockwell Automation®RSLogix™ software: launch the program, configure ladder
logic, and transfer the ladder logic to the processor
Microsoft Windows®:install and launch programs, execute menu commands, navigate
dialog boxes, and enter data
Hardware installation and wiring: install the module, and safely connect IEC 61850
and ControlLogix devices to a power source and to the MVI56E-61850S module’s
application port(s)

Contents MVI56E-61850S ♦ ControlLogix Platform
User Manual IEC 61850 Server Communication Module
Page 8 of 81 ProSoft Technology, Inc.
September 4, 2014
1.1 System Requirements
The MVI56E-61850S module requires the following minimum hardware and software
components:
Rockwell Automation®ControlLogix®processor (firmware version 10 or higher) with
compatible limited voltage power supply and one free slot in the rack for the MVI56E-
61850S module. The module requires 800 mA of available 5 VDC and 3 mA of available
24 VDC power.
Rockwell Automation RSLogix™5000 programming software
oVersion 16 or higher required for Add-On Instruction
Rockwell Automation RSLinx®communication software version 2.51 or higher
ProSoft Configuration Builder (PCB) (included)
ProSoft Discovery Service (PDS) (included in PCB)
Pentium®II 450 MHz minimum. Pentium III 733 MHz (or better) recommended
Supported operating systems:
oMicrosoft Windows®Vista
oMicrosoft Windows XP Professional with Service Pack 1 or 2
oMicrosoft Windows 7 Professional (32 or 64-bit)
oMicrosoft Windows 2000 Professional with Service Pack 1, 2, or 3
oMicrosoft Windows Server 2003
128 MB of RAM minimum, 256 MB of RAM recommended
100 MB of free hard disk space (or more based on application requirements)
256-color VGA graphics adapter, 800 x 600 minimum resolution (True Color 1024 768
recommended)
DVD drive
Note: The Hardware and Operating System requirements in this list are the minimum recommended to install
and run software provided by ProSoft Technology®. Other third party applications may have different minimum
requirements. Refer to the documentation for any third party applications for system requirements.
Note: You can install the module in a local or remote rack. For remote rack installation, the module requires
EtherNet/IP or ControlNet communication with the processor.

MVI56E-61850S ♦ ControlLogix Platform Contents
IEC 61850 Server Communication Module User Manual
ProSoft Technology, Inc. Page 9 of 81
September 4, 2014
1.2 Package Contents
The following components are included with your MVI56E-61850S module, and are all
required for installation and configuration.
Important: Before beginning the installation, please verify that all of the following items are present.
Qty.
Part Name
Part Number
Part Description
1
MVI56E-61850S Module
MVI56E-61850S
IEC 61850 Server Communication Module
1
Ethernet Cable
RL-CBL025
Straight-through Ethernet cable
1
ProSoft Solutions DVD
DVD-001
Contains sample programs, utilities, and documentation.
Files can also be found at
http://www.prosoft-technology.com
If any of these components are missing, please contact ProSoft Technology Technical
Support for replacement parts. If the DVD is not present, please visit
http://www.prosoft-technology.com for the latest files.
1.3 Setting Jumpers
The Setup Jumper acts as "write protection" for the module’s flash memory. In "write
protected" mode, the Setup pins are not connected, and the module’s firmware cannot be
overwritten. The module is shipped with the Setup jumper OFF. Do not jumper the Setup
pins together unless you are directed to do so by ProSoft Technical Support (or to update
the module firmware).
The following illustration shows the MVI56E-61850S jumper configuration with the Setup
Jumper OFF.

Contents MVI56E-61850S ♦ ControlLogix Platform
User Manual IEC 61850 Server Communication Module
Page 10 of 81 ProSoft Technology, Inc.
September 4, 2014
1.4 Installing the Module in the Rack
Make sure your ControlLogix processor and power supply are installed and configured,
before installing the MVI56E-61850S module. Refer to your Rockwell Automation product
documentation for installation instructions.
Warning: You must follow all safety instructions when installing this or any other electronic devices. Failure to
follow safety procedures could result in damage to hardware or data, or even serious injury or death to
personnel. Refer to the documentation for each device you plan to connect to verify that suitable safety
procedures are in place before installing or servicing the device.
After you have checked the placement of the jumpers, insert the MVI56E-61850S into the
ControlLogix chassis. Use the same technique recommended by Rockwell Automation to
remove and install ControlLogix modules.
You can install or remove ControlLogix system components while chassis power is applied
and the system is operating. However, please note the following warning.
Warning: When you insert or remove the module while backplane power is on, an electrical arc can occur. An
electrical arc can cause personal injury or property damage by sending an erroneous signal to the system’s
actuators. This can cause unintended machine motion or loss of process control. Electrical arcs may also cause
an explosion when they happen in a hazardous environment. Verify that power is removed or the area is non-
hazardous before proceeding.
Repeated electrical arcing causes excessive wear to contacts on both the module and its mating connector.
Worn contacts may create electrical resistance that can affect module operation.
1 Align the module with the top and bottom guides, and then slide it into the rack until the
module is firmly against the backplane connector.
2 With a firm, steady push, snap the module into place.
3 Check that the holding clips on the top and bottom of the module are securely in the
locking holes of the rack.

MVI56E-61850S ♦ ControlLogix Platform Contents
IEC 61850 Server Communication Module User Manual
ProSoft Technology, Inc. Page 11 of 81
September 4, 2014
4 Make a note of the slot location. You must identify the slot in which the module is
installed in order for the sample program to work correctly. Slot numbers are identified
on the green circuit board (backplane) of the ControlLogix rack.
5 Turn power ON.
Note: If you insert the module improperly, the system may stop working or may behave unpredictably.

Contents MVI56E-61850S ♦ ControlLogix Platform
User Manual IEC 61850 Server Communication Module
Page 12 of 81 ProSoft Technology, Inc.
September 4, 2014
1.5 Connecting Your PC to the ControlLogix Processor
There are several ways to establish communication between your PC and the ControlLogix
processor. The following steps show how to establish communication through the serial
interface.
Note: It is not mandatory that you use the processor's serial interface. You may access the processor through
whatever network interface is available on your system. Refer to your Rockwell Automation documentation for
information on other connection methods.
1 Connect the right-angle connector end of the cable to your controller at the
communications port.
2 Connect the straight connector end of the cable to the serial port on your computer.

MVI56E-61850S ♦ ControlLogix Platform Contents
IEC 61850 Server Communication Module User Manual
ProSoft Technology, Inc. Page 13 of 81
September 4, 2014
1.6 Downloading the Sample Program to the Processor
Note: The key switch on the front of the ControlLogix processor must be in the REM or PROG position.
1 If you are not already online with the processor, in RSLogix 5000 open the
Communications menu, and then choose DOWNLOAD.RSLogix 5000 will establish
communication with the processor. You do not have to download through the
processor's serial port, as shown here. You may download through any available
network connection.
2 When communication is established, RSLogix 5000 will open a confirmation dialog box.
Click the DOWNLOAD button to transfer the sample program to the processor.
3 RSLogix 5000 will compile the program and transfer it to the processor. This process
may take a few minutes.
4 When the download is complete, RSLogix 5000 will open another confirmation dialog
box. If the key switch is in the REM position, click OK to switch the processor from
PROGRAM mode to RUN mode.
Note: If you receive an error message during these steps, refer to your RSLogix documentation to interpret and
correct the error.

Contents MVI56E-61850S ♦ ControlLogix Platform
User Manual IEC 61850 Server Communication Module
Page 14 of 81 ProSoft Technology, Inc.
September 4, 2014
1.6.1 Configuring the RSLinx Driver for the PC COM Port
When trying to connect serially, if RSLogix is unable to establish communication with the
processor, follow these steps.
1 Open RSLinx.
2 Open the COMMUNICATIONS menu, and click CONFIGURE DRIVERS.
This action opens the Configure Drivers dialog box.
Note: If the list of configured drivers is blank, you must first choose and configure a driver from the Available
Driver Types list. The recommended driver type to choose for serial communication with the processor is RS-232
DF1 Devices.

MVI56E-61850S ♦ ControlLogix Platform Contents
IEC 61850 Server Communication Module User Manual
ProSoft Technology, Inc. Page 15 of 81
September 4, 2014
3 Click to select the driver, and then click CONFIGURE. This action opens the Configure
RS-232 DF1 Devices dialog box.
4 Click the AUTO-CONFIGURE button. RSLinx will attempt to configure your serial port to
work with the selected driver.
5 When you see the message Auto Configuration Successful, click the OK button to
dismiss the dialog box.
Note: If the auto-configuration procedure fails, verify that the cables are connected correctly between the
processor and the serial port on your computer, and then try again. If you are still unable to auto-configure the
port, refer to your RSLinx documentation for further troubleshooting steps.

Contents MVI56E-61850S ♦ ControlLogix Platform
User Manual IEC 61850 Server Communication Module
Page 16 of 81 ProSoft Technology, Inc.
September 4, 2014

MVI56E-61850S ♦ ControlLogix Platform Contents
IEC 61850 Server Communication Module User Manual
ProSoft Technology, Inc. Page 17 of 81
September 4, 2014
2 Setting Up ProSoft Configuration Builder
In This Chapter
Installing ProSoft Configuration Builder .................................................17
Setting Up the Project............................................................................18
ProSoft Configuration Builder (PCB) software provides a convenient way to configure,
monitor, and troubleshoot your MVI56E-61850S module.
2.1 Installing ProSoft Configuration Builder
The ProSoft Configuration Builder (PCB) software is used to configure the module. You can
find the latest version of the ProSoft Configuration Builder (PCB) on our web site:
http://www.prosoft-technology.com, or you can install it from the ProSoft Solutions DVD. The
installation filename contains the PCB version number. For example,
PCB_4.1.0.4.0206.EXE.
If you are installing PCB from the ProSoft website:
1 Open a browser window and navigate to http://www.prosoft-technology.com/pcb.
2 Click the download link for ProSoft Configuration Builder, and save the file to your
Windows desktop.
3 After the download completes, double-click the file to install. If you are using Windows 7,
right-click on the PCB installation file and click RUN AS ADMINISTRATOR. Follow the
instructions that appear on the screen.
4 If you want to find additional software specific to your MVI56E-61850S, enter the model
number into the website search box and press the Enter key.
If you are installing PCB from the ProSoft Solutions DVD:
1 Insert the ProSoft Solutions DVD into your computer's DVD drive and wait for the
ProSoft Installation program to start.
2 If the ProSoft Installation program does not start, open the Windows file Explorer,
navigate to the DVD, and double-click on the ProSoft_DVD.exe file.
3 Navigate to the MVI56E-61850S selection using the PLATFORM and PRODUCT selections.
4 Click PROSOFT CONFIGURATION BUILDER.
5 Follow the instructions that appear on the screen.

Contents MVI56E-61850S ♦ ControlLogix Platform
User Manual IEC 61850 Server Communication Module
Page 18 of 81 ProSoft Technology, Inc.
September 4, 2014
2.2 Setting Up the Project
To begin, start PROSOFT CONFIGURATION BUILDER (PCB).
If you have used other Windows configuration tools before, you will find the screen layout
familiar. PCB’s window consists of a tree view on the left, and an information pane and a
configuration pane on the right side of the window. When you first start PCB, the tree view
consists of folders for Default Project and Default Location, with a Default Module in the
Default Location folder. The following illustration shows the PCB window with a new project.

MVI56E-61850S ♦ ControlLogix Platform Contents
IEC 61850 Server Communication Module User Manual
ProSoft Technology, Inc. Page 19 of 81
September 4, 2014
Your first task is to add the MVI56E-61850S module to the project.
1 Use the mouse to select DEFAULT MODULE in the tree view, and then click the right
mouse button to open a shortcut menu.
2 On the shortcut menu, select CHOOSE MODULE TYPE. This action opens the Choose
Module Type dialog box.
3 In the Product Line Filter area of the dialog box, select MVI56E. In the Select Module
Type dropdown list, select MVI56E-61850S, and then click OK to save your settings and
return to the ProSoft Configuration Builder window.

Contents MVI56E-61850S ♦ ControlLogix Platform
User Manual IEC 61850 Server Communication Module
Page 20 of 81 ProSoft Technology, Inc.
September 4, 2014