ProSoft Technology PLX51-HART-4I User manual

PLX51-HART-4I Quick Start Guide
ProSoft Technology, Inc. Page 1 of 2
November 2018 v1.1
Note: Before installing, configuring, operating, or maintaining ProSoft Technology products, please review this information and
the information located on www.prosoft-technology.com for the latest software, documentation, and installation files specific to
your ProSoft Technology product.
Installation and maintenance of your ProSoft Technology product(s) should be carried out by suitably trained personnel in
accordance with applicable codes of practice. In case of malfunction or damage, no attempts of repair should be made. Your
ProSoft Technology product(s) should be returned to the manufacturer for repair. Do not dismantle the product.
For professional users in the European Union
If you wish to discard electrical and electronic equipment (EEE), please contact your dealer or supplier for further
information.
WARNING –Cancer and reproductive harm –www.p65warnings.ca.gov
Your Feedback Please
We always want you to feel that you made the right decision to use our products. If you have suggestions, comments,
compliments or complaints about our products, documentation, or support, please write or call us.
ProSoft Technology, Inc.
[phone]
[phone] (Fax)
www.prosoft-technology.com
[email protected]
ProSoft Technology®, is a registered copyright of ProSoft Technology, Inc. All other brand or product names are or may be
trademarks of, and are used to identify products and services of, their respective owners.
Documentation is subject to change without notice.
North American Hazardous Location Approval
The following information applies when operating the product in hazardous locations:
THIS EQUIPMENT IS AN OPEN-TYPE DEVICE AND IS MEANT TO BE INSTALLED IN AN ENCLOSURE SUITABLE
FOR THE ENVIRONMENT SUCH THAT THE EQUIPMENT IS ONLY ACCESSIBLE WITH THE USE OF A TOOL.
SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C AND D HAZARDOUS LOCATIONS, OR
NONHAZARDOUS LOCATIONS ONLY.
Required Software
The PLX51-HART-4I requires the ProSoft PLX50 Configuration Utility to setup and configure. The software installation can be
found at: www.prosoft-technology.com
Ethernet Network Setup
The PLX51-HART-4I has DHCP enabled as factory default. Launch the DHCP server for the ProSoft PLX50 Configuration
Utility to assign an IP address to the module. You can then configure the module with ProSoft PLX50 Configuration Utility.

PLX51-HART-4I Quick Start Guide
ProSoft Technology, Inc. Page 2 of 2
November 2018 v1.1
Module Installation
The PLX51-HART-4I requires input power of 10 to 28 VDC and communicates on Ethernet.
Analog Input Equivalent Circuit
Analog (HART) Connection to Field Device
Additional Information
Resource
Link
HART Communication Foundation
https://fieldcommgroup.org/technologies/hart/hart-technology
DNP3 Ethernet
http://www.dnp.org
Support, Service, and Warranty
Note: For technical support calls within the United States, ProSoft Technology’s 24/7 after-hours phone support is available
for urgent plant-down issues. Detailed contact information for all our worldwide locations is shown below:
Internet
Website: www.prosoft-technology.com/support
Email: [e-mail]
North America
Tel: [phone]
Email: [e-mail]
Languages spoken include: English, Spanish
Asia Pacific
Tel: [phone]
Email: [e-mail]
Languages spoken include: Bahasa, Chinese, English, Japanese, Korean
Europe / Middle East / Africa
Tel: [phone]
Email: [e-mail]
Languages spoken include: French, English
Latin America (Spanish Speaking Countries)
Tel: [phone]
Email: [e-mail]
Languages spoken include: Spanish, English
Latin America (Brasil)
Tel: [phone]
Email: [e-mail]
Languages spoken include: Portuguese, English
For complete details regarding ProSoft Technology’s TERMS & CONDITIONS OF SALE, WARRANTY, SUPPORT, SERVICE
AND RETURN MATERIAL AUTHORIZATION INSTRUCTIONS, please see the documents at:
www.prosoft-technology.com/legal