ProSoft Technology MVI69E-GSC User manual

MVI69E-GSC
CompactLogix™or
MicroLogix™Platform
Generic ASCII Serial
Communication Module
June 16, 2020
USER MANUAL

Contents MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform
User Manual Generic ASCII Serial Communication Module
Page 2 of 87 ProSoft Technology, Inc.
Your Feedback Please
We always want you to feel that you made the right decision to use our products. If you have suggestions,
comments, compliments or complaints about our products, documentation, or support, please write or call us.
ProSoft Technology, Inc.
[phone]
[phone] (Fax)
www.prosoft-technology.com
[e-mail]
MVI69E-GSC User Manual
June 16, 2020
ProSoft Technology®, is a registered copyright of ProSoft Technology, Inc. All other brand or product names are
or may be trademarks of, and are used to identify products and services of, their respective owners.
In an effort to conserve paper, ProSoft Technology no longer includes printed manuals with our product
shipments. User Manuals, Datasheets, Sample Ladder Files, and Configuration Files are provided at our
website:
www.prosoft-technology.com
Content Disclaimer
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability
of these products for specific user applications. It is the duty of any such user or integrator to perform the
appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant
specific application or use thereof. Neither ProSoft Technology nor any of its affiliates or subsidiaries shall be
responsible or liable for misuse of the information contained herein. Information in this document including
illustrations, specifications and dimensions may contain technical inaccuracies or typographical errors. ProSoft
Technology makes no warranty or representation as to its accuracy and assumes no liability for and reserves the
right to correct such inaccuracies or errors at any time without notice. If you have any suggestions for
improvements or amendments or have found errors in this publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic or mechanical, including
photocopying, without express written permission of ProSoft Technology. All pertinent state, regional, and local
safety regulations must be observed when installing and using this product. For reasons of safety and to help
ensure compliance with documented system data, only the manufacturer should perform repairs to components.
When devices are used for applications with technical safety requirements, the relevant instructions must be
followed. Failure to use ProSoft Technology software or approved software with our hardware products may
result in injury, harm, or improper operating results. Failure to observe this information can result in injury or
equipment damage.
© 2020 ProSoft Technology. All Rights Reserved.
Printed documentation is available for purchase. Contact ProSoft Technology for pricing and availability.
For professional users in the European Union
If you wish to discard electrical and electronic equipment (EEE), please contact your dealer or
supplier for further information.
Warning –Cancer and Reproductive Harm –www.P65Warnings.ca.gov

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform Contents
Generic ASCII Serial Communication Module User Manual
ProSoft Technology, Inc. Page 3 of 87
Important Safety Information
North America Warnings
A This Equipment is Suitable For Use in Class I, Division 2, Groups A, B, C, D or Non-Hazardous Locations
Only.
B Warning –Explosion Hazard –Substitution of Any Components May Impair Suitability for Class I, Division 2.
C Warning –Explosion Hazard –Do Not Disconnect Equipment Unless Power Has Been Switched Off Or The
Area is Known To Be Non-Hazardous.
D The subject devices are powered by a Switch Model Power Supply (SMPS) that has regulated output
voltage of 5 VDC.
ATEX/IECEx Warnings and Conditions of Safe Usage:
Power, Input, and Output (I/O) wiring must be in accordance with the authority having jurisdiction.
A Warning - Explosion Hazard - When in hazardous locations, turn off power before replacing or wiring
modules.
B Warning - Explosion Hazard - Do not disconnect equipment unless power has been switched off or the area
is known to be non-hazardous.
C These products are intended to be mounted in an ATEX/IECEx Certified, tool-secured, IP54 enclosure. The
devices shall provide external means to prevent the rated voltage being exceeded by transient disturbances
of more than 40%. This device must be used only with ATEX certified backplanes.
D Before operating the reset switch, be sure the area is known to be non-hazardous.
If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment
may be impaired.
Agency Approvals & Certifications
Please visit our website: www.prosoft-technology.com

Contents MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform
User Manual Generic ASCII Serial Communication Module
Page 4 of 87 ProSoft Technology, Inc.
Contents
Your Feedback Please......................................................................................................................2
Content Disclaimer............................................................................................................................2
Important Safety Information.............................................................................................................3
1Start Here 6
1.1 System Requirements .............................................................................................6
1.2 Package Contents ...................................................................................................7
1.3 Setting Jumpers.......................................................................................................7
1.4 Install the Module in the Rack..................................................................................9
2Configuring the Module in RSLogix 12
2.1 Creating the Module in an Studio 5000 Project.....................................................12
2.1.1 Creating a Module in the Project Using an Add-On Profile ...................................13
2.1.2 Creating a Module in the Project Using a Generic 1769 Module Profile ...............17
2.2 Importing the Add-On Instruction...........................................................................19
2.2.1 Importing the Add-On Instruction...........................................................................19
2.2.2 Adding Multiple Modules in the Rack (Optional)....................................................22
2.3 Downloading the Sample Program to the Processor.............................................27
3Optional AOI 28
3.1 Importing the Optional AOI ....................................................................................28
3.2 Setting up the Optional AOI...................................................................................30
3.3 Synchronizing the IP Settings from the MVI69E-GSC to the Processor...............32
3.4 Synchronizing the IP Settings from the Processor to the MVI69E-GSC...............33
3.5 Reading the Date/Time from the MVI69E-GSC to the Processor .........................34
3.6 Writing the Date/Time from the Processor to the MVI69E-GSC ...........................35
4Using ProSoft Configuration Builder 36
4.1 Installing ProSoft Configuration Builder Software..................................................36
4.2 Setting Up the Project............................................................................................36
4.2.1 Adding the MVI69E-GSC module to the project....................................................37
4.3 Renaming PCB Objects.........................................................................................38
4.4 Module Configuration Parameters.........................................................................39
4.4.1 Module Parameters ...............................................................................................39
4.4.2 GSC Port x Parameters.........................................................................................40
4.4.3 MVI69E-GSC IP Address Configuration................................................................42
4.5 Downloading the Configuration File to the Module................................................43
4.6 Uploading the Configuration File from the Module ................................................45
4.7 Converting a Legacy MVI69-GSC to an MVI69E-GSC .........................................47
5Using Controller Tags 48
5.1 MVI69E-GSC Controller Tags ...............................................................................49
5.2 User-Defined Data Types (UDTs)..........................................................................50
5.2.1 MVI69E-GSC User-Defined Data Types ...............................................................50
5.3 GSC Controller Tag Overview...............................................................................51

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform Contents
Generic ASCII Serial Communication Module User Manual
ProSoft Technology, Inc. Page 5 of 87
5.3.1 GSC.DATA.............................................................................................................51
5.3.2 GSC.STATUS ........................................................................................................52
5.3.3 GSC.CONTROL.....................................................................................................52
6Transmitting ASCII Data 53
6.1 Sending ASCII Strings from the Processor to a Serial Device...............................53
6.2 Receiving ASCII Strings from a Serial Device to the Processor............................54
7Diagnostics and Troubleshooting 55
7.1 LED Status Indicators.............................................................................................55
7.2 Ethernet LED Indicators.........................................................................................56
7.3 Clearing a Fault Condition......................................................................................56
7.4 Troubleshooting......................................................................................................57
7.5 Configuring a Temporary IP Address.....................................................................58
7.6 Diagnostics Menu...................................................................................................60
7.6.1 Diagnostics Menu Navigation.................................................................................62
7.6.2 Monitoring Network Configuration Information.......................................................62
7.6.3 Monitoring Backplane Information..........................................................................63
7.6.4 Port x Module Information......................................................................................64
7.6.5 Data Analyzer.........................................................................................................65
7.7 Connecting to the Module’s Webpage ...................................................................68
8Reference 69
8.1 Product Specifications............................................................................................69
8.1.1 Hardware Specifications.........................................................................................69
8.1.2 Functional Specifications........................................................................................70
8.2 Functional Overview...............................................................................................71
8.2.1 General Concepts ..................................................................................................71
8.2.2 Backplane Data Flow .............................................................................................71
8.2.3 Special Function Blocks.........................................................................................75
8.3 Ethernet Port Connection.......................................................................................76
8.3.1 Ethernet Cable Specifications................................................................................76
8.4 Application Port Cable Connection ........................................................................77
8.4.1 RS-232 Wiring........................................................................................................77
8.4.2 RS-422 Wiring........................................................................................................80
8.4.3 RS-485 Wiring........................................................................................................80
8.4.4 DB9 to RJ45 Adaptor (Cable 14) ...........................................................................81
8.5 Status Data Definition.............................................................................................82
9Support, Service & Warranty 85
9.1 Contacting Technical Support................................................................................85
9.2 Warranty Information..............................................................................................85
Index 86

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
Page 6 of 87 ProSoft Technology, Inc.
1 Start Here
To get the most benefit from this User Manual, you know the following skills:
Studio 5000 Logix Designer®:launch the program, configure ladder logic, and transfer
the ladder logic to the processor
Microsoft Windows: install and launch programs, execute menu commands, navigate
dialog boxes, and enter data
Hardware installation and wiring: install the module, and safely connect and
CompactLogix or MicroLogix devices to a power source and to the MVI69E-GSC
module’s application port(s)
1.1 System Requirements
The MVI69E-GSC module requires the following minimum hardware and software
components:
Rockwell Automation CompactLogix or MicroLogix 1500-LRP®processor (firmware
version 10 or higher), with compatible power supply and one free slot in the rack, for the
MVI69E-GSC module.
Important: The MVI69E-GSC module has a power supply distance rating of 4 (L43 and L45 installations on first
2 slots of 1769 bus). It consumes 500 mA at 5 VDC.
Important: For 1769-L23x processors, please make note of the following limitation:
1769-L23E-QBFC1B = 450 mA at 5 VDC (No MVI69E module can be used with this processor.)
The module requires 500 mA of available 5 VDC power
Rockwell Automation Studio 5000 Logix Designer version 16 or higher
Rockwell Automation RSLinx®communication software version 2.51 or higher
ProSoft Configuration Builder (PCB) (included)
ProSoft Discovery Service (PDS) (included in PCB)
Pentium®II 450 MHz minimum. Pentium III 733 MHz (or better) recommended
Supported operating systems:
oMicrosoft Windows 10
oMicrosoft Windows 7 Professional (32-or 64-bit)
oMicrosoft Windows XP Professional with Service Pack 1 or 2
oMicrosoft Windows Vista
oMicrosoft Windows 2000 Professional with Service Pack 1, 2, or 3
oMicrosoft Windows Server 2003
128 Mbytes of RAM minimum, 256 Mbytes of RAM recommended
100 Mbytes of free hard disk space (or more based on application requirements)
256-color VGA graphics adapter, 800 x 600 minimum resolution
Note: The Hardware and Operating System requirements in this list are the minimum recommended to install
and run software provided by ProSoft Technology®. Other third party applications may have different minimum
requirements.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
ProSoft Technology, Inc. Page 7 of 87
1.2 Package Contents
The following components are included with your MVI69E-GSC module, and are all required
for installation and configuration.
Important: Before beginning the installation, please verify that all of the following items are present.
Qty.
Part Name
Part Number
Part Description
1
MVI69E-GSC Module
MVI69E-GSC
Generic ASCII Serial Communication
Module
2
Adapter Cable
Cable #14
RJ45 to DB9 Male Adapter cable. For DB9
connection to module’s serial application
ports
2
Screw Terminal
Adapter
1454-9F
DB9 female to 9-pin screw terminal. Used
for RS422 or RS485 connections to Port 1
and 2 of the module
If any of these components are missing, please contact ProSoft Technology Support for
replacement parts.
1.3 Setting Jumpers
When the module is manufactured, the port selection jumpers are set to RS-232. To use
RS-422 or RS-485, you must set the jumpers to the correct position. The following diagram
describes the jumper settings.
Note: Jumper pin placement on the circuit board may vary.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
Page 8 of 87 ProSoft Technology, Inc.
The Setup Jumper acts as "write protection" for the module’s firmware. In "write protected"
mode, the Setup pins are not connected, and the module’s firmware cannot be overwritten.
The module is shipped with the Setup jumper OFF. If an update of the firmware is needed,
apply the Setup jumper to both pins.
The following illustration shows the MVI69E-GSC jumper configuration, with the Setup
Jumper OFF.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
ProSoft Technology, Inc. Page 9 of 87
1.4 Install the Module in the Rack
Make sure the processor and power supply are installed and configured before installing the
MVI69E-GSC module. Refer to the Rockwell Automation product documentation for
installation instructions.
Warning: Please follow all safety instructions when installing this or any other electronic devices. Failure to
follow safety procedures could result in damage to hardware or data, or even serious injury or death to
personnel. Refer to the documentation for each device to be connected to verify that suitable safety procedures
are in place before installing or servicing the device.
After you verify the jumper placements, insert the MVI69E-GSC into the rack. Use the same
technique recommended by Rockwell Automation to remove and install CompactLogix or
MicroLogix 1500-LRP modules.
Warning: This module is not hot-swappable! Always remove power from the rack before inserting or
removing this module, or damage may result to the module, the processor, or other connected devices.
1 Align the module using the upper and lower tongue-and-groove slots with the adjacent
module and slide forward in the direction of the arrow.
2 Move the module back along the tongue-and-groove slots until the bus connectors on
the module and the adjacent module line up with each other.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
Page 10 of 87 ProSoft Technology, Inc.
3 Push the module’s bus lever back slightly to clear the positioning tab and move it firmly
to the left until it clicks. Ensure that it is locked firmly in place.
4 Close all DIN-rail latches.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
ProSoft Technology, Inc. Page 11 of 87
5 Press the DIN-rail mounting area of the controller against the DIN-rail. The latches will
momentarily open and lock into place.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
Page 12 of 87 ProSoft Technology, Inc.
2 Configuring the Module in RSLogix
To add the MVI69E-MBS module in Studio 5000, you must:
1 Create a new project in Studio 5000.
2 Add the module to the Studio 5000 project. There are two ways to do this:
oYou can use the Add-On Profile from ProSoft Technology. This is the preferred way,
but requires RSLogix version 15 or later.
oYou can manually create the module using a generic 1769 profile, and then manually
configure the module parameters. Use this method if you have RSLogix version 14 or
earlier.
3 Download the MVI69EGSC_AddOn_Rung.L5X file from www.prosoft-technology.com.
4 Import the Add-On Instruction (the .L5X file) into Studio 5000.
The .L5X file contains the Add-On Instruction, user-defined data types, controller tags and
ladder logic required to configure the MVI69E-GSC module.
2.1 Creating the Module in an Studio 5000 Project
In an Studio 5000 project, there are two ways you can add the MVI69E-MBS module to the
project.
You can use an Add-On Profile (AOP) from ProSoft Technology. The AOP contains all
the configuration information needed to add the module to the project. This is the
preferred way, but requires RSLogix version 15 or later. Refer to Creating a Module in
the Project Using an Add-On Profile (page Creating a Module in the Project Using an
Add-On Profile13).
If using an AOP is not an option, you can manually create and configure the module
using a generic 1769 profile. Use this method if you have RSLogix version 14 or earlier.
Refer to Creating a Module in the Project Using a Generic 1769 Module Profile (page
17).

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
ProSoft Technology, Inc. Page 13 of 87
2.1.1 Creating a Module in the Project Using an Add-On Profile
Installing an Add-On Profile
Download the AOP file (MVI69x_RevX.X_AOP.zip) from the product webpage (www.prosoft-
technology.com) onto your local hard drive and then extract the files from the zip archive.
Make sure you have shut down Studio 5000 and RSLinx before you install the Add-On
Profile (AOP).
1 Run the MPSetup.exe file to start the Setup Wizard. Follow the Setup Wizard to install
the AOP.
2 Continue to follow the steps in the wizard to complete the installation.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
Page 14 of 87 ProSoft Technology, Inc.
3 Click FINISH when complete. The AOP is now installed in Studio 5000. You do not need
to reboot the PC.
Using an Add-On Profile
1 In Studio 5000, expand the I/O CONFIGURATION folder in the Project tree. Right-click the
appropriate communications bus and, and then click NEW MODULE.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
ProSoft Technology, Inc. Page 15 of 87
2 This opens the Select Module Type dialog box. In the Module Type Vendor Filters area,
uncheck all boxes except the PROSOFT TECHNOLOGY box. Then select the MVI69 option
and click the CREATE button.
3 A New Module dialog box opens. Edit the NAME and SLOT for the module.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
Page 16 of 87 ProSoft Technology, Inc.
4 In the Connection tab, select the Request Packet Interval value for scanning the I/O on
the module. This value represents the minimum frequency the module will handle
scheduled events. This value should not be set to less than 1 millisecond. Values
between 1 and 10 milliseconds should work with most applications. Click OK.
5 The MVI69E-GSC is now visible in the I/O Configuration section.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
ProSoft Technology, Inc. Page 17 of 87
2.1.2 Creating a Module in the Project Using a Generic 1769 Module Profile
This procedure is not required if you installed the ProSoft Technology Add-On Profile for this
module.
1 Expand the I/O CONFIGURATION folder in the Project tree. Right-click the appropriate
communications bus and choose NEW MODULE.
This opens the Select Module Type dialog box.
2 In the Select Module Type dialog, select the 1769-MODULE and click on the CREATE
button.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
Page 18 of 87 ProSoft Technology, Inc.
3 Set the Module Properties values as follows:
Parameter
Value
Name
Enter a module identification string. Example: MVI69EGSC
Description
Enter a description for the module. Example: ProSoft
communication module for Serial Modbus communications.
Comm Format
Select DATA-INT
Slot
Enter the slot number in the rack where the MV69E-GSC
module is installed.
Input Assembly Instance
101
Input Size
60
Output Assembly Instance
100
Output Size
60
Configuration Assembly Instance
102
Configuration Size
0
4 On the Connection tab, set the REQUESTED PACKET INTERVAL value for your project and
click OK.
The MVI69E-MBS module is now visible in the I/O Configuration tree.

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
ProSoft Technology, Inc. Page 19 of 87
2.2 Importing the Add-On Instruction
Note: This section only applies if you are using Studio 5000 version 16 or higher. If you are configuring the
MVI69E-GSC module with an earlier version of Studio 5000, please refer to Adding the Module to an Existing
CompactLogix Project (page 27).
The following file is required before you start this procedure. You can download it from
www.prosoft-technology.com.
File Name
Description
MVI69EGSC_AddOn_Rung.L5X
File containing Add-On instruction, user defined data types,
data objects and ladder logic required to set up the MVI69E-
GSC module
2.2.1 Importing the Add-On Instruction
1 In RSLogix, expand the Tasks > Main Task > Main Program folder.
2 Double-click on the MainRoutine icon.
3 In an empty rung, right-click the mouse button to open a shortcut menu.
4 On the shortcut menu, choose IMPORT RUNGS…

MVI69E-GSC ♦ CompactLogix™ or MicroLogix™ Platform User Manual
Page 20 of 87 ProSoft Technology, Inc.
5 Select the MVI69EGSC_AddOn_Rung_v1_x.L5X file. The Add-On Instruction file is
located at www.prosoft-technology.com. Click on the IMPORT button.
6 The following window displays the controller tags to be created during the import
procedure. Make sure the slot number reference (Local:x) is correct.