ProSoft MVI56E-FLN User manual

MVI56E-FLN
ControlLogix Platform
FA Control Network Ethernet
Communication Module
July 10, 2019
USER MANUAL

Your Feedback Please
We always want you to feel that you made the right decision to use our products. If you have suggestions, comments,
compliments or complaints about our products, documentation, or support, please write or call us.
How to Contact Us
ProSoft Technology, Inc.
[phone]
[phone] (Fax)
www.prosoft-technology.com
[email protected]
Copyright © 2019 ProSoft Technology, Inc. All rights reserved.
MVI56E-FLN User Manual
July 10, 2019
ProSoft Technology ®, ProLinx ®, inRAx ®, ProTalk ®, and RadioLinx ®are Registered Trademarks of ProSoft
Technology, Inc. All other brand or product names are or may be trademarks of, and are used to identify products
and services of, their respective owners.
ProSoft Technology®Product Documentation
In an effort to conserve paper, ProSoft Technology no longer includes printed manuals with our product shipments.
User Manuals, Datasheets, Sample Ladder Files, and Configuration Files are provided at:
www.prosoft-technology.com
For professional users in the European Union
If you wish to discard electrical and electronic equipment (EEE), please contact your dealer or supplier
for further information.
Warning –Cancer and Reproductive Harm –www.P65Warnings.ca.gov

Important Safety Information
North America Warnings
WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS
I, DIV. 2;
WARNING - EXPLOSION HAZARD - WHEN IN HAZARDOUS LOCATIONS, TURN OFF POWER BEFORE
REPLACING OR WIRING MODULES
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN
SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
Class 2 Power
ATEX Warnings and Conditions of Safe Usage
Power, Input, and Output (I/O) wiring must be in accordance with the authority having jurisdiction
A Warning - Explosion Hazard - When in hazardous locations, turn off power before replacing or wiring modules.
B Warning - Explosion Hazard - Do not disconnect equipment unless power has been switched off or the area is
known to be non-hazardous.
C These products are intended to be mounted in an IP54 enclosure. The devices shall provide external means to
prevent the rated voltage being exceeded by transient disturbances of more than 40%. This device must be used
only with ATEX certified backplanes.
D DO NOT OPEN WHEN ENERGIZED.
Electrical Ratings
Backplane Current Load: 800 mA @ 5 Vdc; 3 mA @ 24 Vdc
Operating Temperature: 0°C to 60°C (32°F to 140°F)
Storage Temperature: -40°C to 85°C (-40°F to 185°F)
Shock: 30 g operational; 50 g non-operational; Vibration: 5 g from 10 Hz to 150 Hz
Relative Humidity 5% to 95% (without condensation)
All phase conductor sizes must be at least 1.3 mm (squared) and all earth ground conductors must be at least
4mm (squared).
Label Markings
Class I Division 2 Groups A, B, C, and D
Temp Code T5
II 3 G
Ex nA nL IIC T5 X
0°C <= Ta <= 60°C
II –Equipment intended for above ground use (not for use in mines).
3 –Category 3 equipment, investigated for normal operation only.
G –Equipment protected against explosive gasses.

Agency Approvals and Certifications
Please visit our website: www.prosoft-technology.com
Battery Life Advisory
Note: Modules manufactured after April 1st, 2011 do not contain a battery. For modules
manufactured before that date the following applies:
The module uses a rechargeable Lithium Vanadium Pentoxide battery to back up the real-time clock and CMOS
settings. The battery itself should last for the life of the module. However, if left in an unpowered state for 14 to 21
days, the battery may become fully discharged and require recharging by being placed in a powered-up ControlLogix
chassis. The time required to fully recharge the battery may be as long as 24 hours.
Once it is fully charged, the battery provides backup power for the CMOS setup and the real-time clock for
approximately 21 days. Before you remove a module from its power source, ensure that the battery within the module
is fully charged (the BATT LED on the front of the module goes OFF when the battery is fully charged). If the battery
is allowed to become fully discharged, the module will revert to the default BIOS and clock settings.
Note: The battery is not user-replaceable or serviceable.

MVI56E-FLN ♦ ControlLogix Platform Contents
FA Control Network Ethernet Communication Module User Manual
ProSoft Technology, Inc. Page 5 of 155
Contents
Your Feedback Please........................................................................................................................2
How to Contact Us..............................................................................................................................2
ProSoft Technology®Product Documentation....................................................................................2
Important Safety Information...............................................................................................................3
Battery Life Advisory...........................................................................................................................4
1Start Here 9
1.1 What's New? ...........................................................................................................10
1.2 System Requirements.............................................................................................11
1.3 Package Contents...................................................................................................12
1.4 Setting Jumpers ......................................................................................................13
1.5 Installing the Module in the Rack ............................................................................14
1.6 Installing ProSoft Configuration Builder ..................................................................15
1.7 Connecting Your PC to the Module.........................................................................16
1.8 Setting Up a Temporary IP Address .......................................................................17
1.9 Connecting to the Module's Web Page...................................................................22
1.10 Using the RSLogix 5000 Sample Project................................................................23
1.10.1 Opening the Sample Ladder Logic..........................................................................23
1.10.2 Adding the Module to an Existing Project ...............................................................28
1.10.3 Connecting Your PC to the ControlLogix Processor...............................................31
1.10.4 Downloading the Sample Program to the Processor..............................................32
2Configuring the MVI56E-FLN Module 33
2.1 Using ProSoft Configuration Builder Software........................................................33
2.1.1 Setting Module Parameters.....................................................................................34
2.2 Module Configuration ..............................................................................................36
2.2.1 FL-net......................................................................................................................36
2.2.2 Ethernet Configuration ............................................................................................40
2.3 Downloading the Project to the Module ..................................................................42
2.4 Configuring the FL-net Device ................................................................................44
2.4.1 Setting Up the FL/ET-T-V2 Module.........................................................................44
2.4.2 FL/ET-V2 Configuration with PCwin........................................................................45
2.4.3 Downloading the Project .........................................................................................50
2.4.4 Connecting the MVI56E-FLN Module to the FL/ET-T-V2 .......................................50
2.5 Verifying Communication ........................................................................................51
2.5.1 Using the Diagnostics Menu in ProSoft Configuration Builder................................51
2.5.2 The Diagnostics Menu.............................................................................................54
2.5.3 Checking Status through ControlLogix Controller Tags..........................................61
2.5.4 Transferring Data ....................................................................................................70
3Diagnostics and Troubleshooting 75
3.1 Reading Status Data from the Module....................................................................75
3.1.1 Own-Node Status information.................................................................................76
3.2 Diagnostics Menu Items..........................................................................................78
3.2.1 Monitoring Module Information................................................................................78
3.2.2 Monitoring Backplane Information...........................................................................80
3.3 LED Status Indicators..............................................................................................81

Contents MVI56E-FLN ♦ ControlLogix Platform
User Manual FA Control Network Ethernet Communication Module
Page 6 of 155 ProSoft Technology, Inc.
3.3.1 Scrolling LED Status Indicators.............................................................................. 81
3.3.2 Ethernet LED Indicators.......................................................................................... 82
3.3.3 Non-Scrolling LED Status Indicators ...................................................................... 83
3.4 Clearing a Fault Condition ...................................................................................... 84
3.5 Troubleshooting...................................................................................................... 85
4Reference 87
4.1 Product Specifications ............................................................................................ 87
4.1.1 Features.................................................................................................................. 88
4.1.2 General Specifications............................................................................................ 89
4.1.3 Hardware Specifications......................................................................................... 89
4.1.4 Functional Specifications........................................................................................ 90
4.2 Functional Overview ............................................................................................... 91
4.2.1 About FL-net Protocol............................................................................................. 91
4.2.2 Data Flow between Module and Processor............................................................ 99
4.2.3 Backplane Data Transfer...................................................................................... 100
4.3 Implementation of FL-net...................................................................................... 106
4.3.1 Information Tables................................................................................................ 107
4.3.2 Upper Layer Status Read Definition..................................................................... 110
4.3.3 Lower Layer Protocol............................................................................................ 115
4.4 FL-net Protocol and Network................................................................................ 116
4.4.1 Understanding the Basics of FL-net ..................................................................... 116
4.4.2 Data Frame ID of FL-net....................................................................................... 116
4.4.3 Allowable Refresh Cycle Time.............................................................................. 117
4.4.4 Memory Resources............................................................................................... 117
4.4.5 Message Transmissions....................................................................................... 118
4.4.6 Message Transmission Function.......................................................................... 120
4.4.7 Data Volume and Number of Frames................................................................... 122
4.4.8 Network Management........................................................................................... 123
4.4.9 Masterless Transmission Management................................................................ 123
4.4.10 FA Link Protocol.................................................................................................... 126
4.5 Error and Status Data........................................................................................... 128
4.5.1 Status Data........................................................................................................... 128
4.6 FL-net Device Profile for MVI56E-FLN Module.................................................... 129
4.6.1 Text Notation of Profile ......................................................................................... 129
4.7 Module Power Up ................................................................................................. 132
4.7.1 Main Logic Loop ................................................................................................... 132
4.8 State Transition Diagram...................................................................................... 132
4.8.1 A. State Definitions ............................................................................................... 132
4.8.2 B. Initialization Monitoring..................................................................................... 134
4.8.3 C. Network Initialization ........................................................................................ 136
4.8.4 D. Halfway Joining Initialization............................................................................ 137
4.8.5 E. Waiting for Token ............................................................................................. 138
4.8.6 F. Token Holding .................................................................................................. 139
4.8.7 G. Message Transmission State Transition.......................................................... 140
4.8.8 H. Message Reception State Transition............................................................... 141
4.9 Cable Connections - MVI56E-FLN ....................................................................... 142
4.9.1 Ethernet Connection............................................................................................. 142
4.9.2 Ethernet Cable Specifications............................................................................... 142
5Support, Service & Warranty 145
5.1 Contacting Technical Support............................................................................... 145

MVI56E-FLN ♦ ControlLogix Platform Contents
FA Control Network Ethernet Communication Module User Manual
ProSoft Technology, Inc. Page 7 of 155
Glossary of Terms 149
Index 153

Contents MVI56E-FLN ♦ ControlLogix Platform
User Manual FA Control Network Ethernet Communication Module
Page 8 of 155 ProSoft Technology, Inc.

MVI56E-FLN ♦ ControlLogix Platform Start Here
FA Control Network Ethernet Communication Module User Manual
ProSoft Technology, Inc. Page 9 of 155
1 Start Here
In This Chapter
What's New? .........................................................................................10
System Requirements...........................................................................11
Package Contents.................................................................................12
Setting Jumpers ....................................................................................13
Installing the Module in the Rack...........................................................14
Installing ProSoft Configuration Builder.................................................15
Connecting Your PC to the Module.......................................................16
Setting Up a Temporary IP Address......................................................17
Connecting to the Module's Web Page .................................................22
Using the RSLogix 5000 Sample Project...............................................23
To get the most benefit from this User Manual, you should have the following
skills:
Rockwell Automation®RSLogix™ software: launch the program, configure
ladder logic, and transfer the ladder logic to the processor
Microsoft Windows: install and launch programs, execute menu commands,
navigate dialog boxes, and enter data
Hardware installation and wiring: install the module, and safely connect
FL-net and ControlLogix devices to a power source and to the MVI56E-FLN
module’s application port(s)

Start Here MVI56E-FLN ♦ ControlLogix Platform
User Manual FA Control Network Ethernet Communication Module
Page 10 of 155 ProSoft Technology, Inc.
1.1 What's New?
MVI56E products are backward compatible with existing MVI56 products,
ladder logic, and module configuration files already in use. Easily swap and
upgrade products while benefiting from an array of new features designed to
improve interoperability and enhance ease of use.
ProSoft Configuration Builder (PCB): New Windows software for
diagnostics, connecting via the module's Ethernet port to upload/download
module configuration information and access troubleshooting features and
functions.
ProSoft Discovery Service (PDS): Utility software to find and display a list
of MVI56E modules on the network and to temporarily change an IP address
to connect with a module's web page.
Personality Card: An industrial compact flash memory card storing the
module’s complete configuration and Ethernet settings, allowing quick and
easy replacement.
LED Scrolling Diagnostic Display: 4-character, alphanumeric display,
providing English messages for status and alarm data, and for processor and
network communication status.

MVI56E-FLN ♦ ControlLogix Platform Start Here
FA Control Network Ethernet Communication Module User Manual
ProSoft Technology, Inc. Page 11 of 155
1.2 System Requirements
The MVI56E-FLN module requires the following minimum hardware and software
components:
Rockwell Automation ControlLogix®processor (firmware version 10 or
higher), with compatible power supply, and one free slot in the rack for the
MVI56E-FLN module. The module requires 800 mA of available 5 Vdc power
Rockwell Automation RSLogix 5000 programming software
Rockwell Automation RSLinx®communication software version 2.51 or higher
ProSoft Configuration Builder (PCB) (included)
ProSoft Discovery Service (PDS) (included in PCB)
Pentium®II 450 MHz minimum. Pentium III 733 MHz (or better)
recommended
Supported operating systems:
oMicrosoft Windows 10
oMicrosoft Windows 7 Professional (32-or 64-bit)
oMicrosoft Windows XP Professional with Service Pack 1 or 2
oMicrosoft Windows Vista
oMicrosoft Windows 2000 Professional with Service Pack 1, 2, or 3
oMicrosoft Windows Server 2003
128 Mbytes of RAM minimum, 256 Mbytes of RAM recommended
100 Mbytes of free hard disk space (or more based on application
requirements)
256-color VGA graphics adapter, 800 x 600 minimum resolution (True Color
1024 x 768 recommended)
Note: The Hardware and Operating System requirements in this list are the
minimum recommended to install and run software provided by ProSoft
Technology®. Other third party applications may have different minimum
requirements. Refer to the documentation for any third party applications for
system requirements.
Note: You can install the module in a local or remote rack. For remote rack
installation, the module requires EtherNet/IP or ControlNet communication with
the processor.

Start Here MVI56E-FLN ♦ ControlLogix Platform
User Manual FA Control Network Ethernet Communication Module
Page 12 of 155 ProSoft Technology, Inc.
1.3 Package Contents
The following components are included with your MVI56E-FLN module, and are
all required for installation and configuration.
Important: Before beginning the installation, please verify that all of the following
items are present.
Qty.
Part Name
Part Number
Part Description
1
MVI56E-FLN Module
MVI56E-FLN
FA Control Network Communication Module
If any of these components is missing, please contact ProSoft Technology
Support for replacement parts.

MVI56E-FLN ♦ ControlLogix Platform Start Here
FA Control Network Ethernet Communication Module User Manual
ProSoft Technology, Inc. Page 13 of 155
1.4 Setting Jumpers
The Setup Jumper acts as "write protection" for the module’s flash memory. In
"write protected" mode, the Setup pins are not connected, and the module’s
firmware cannot be overwritten. Do not jumper the Setup pins together unless
you are directed to do so by ProSoft Technical Support.
The following illustration shows the MVI56E-FLN jumper configuration.
Note: If you are installing the module in a remote rack, you may prefer to leave
the Setup pins jumpered. That way, you can update the module’s firmware
without requiring physical access to the module.
Security considerations:
Leaving the Setup pin jumpered leaves the module open to unexpected firmware
updates.
You should consider segmenting the data flow for security reasons. Per IEC
62443-1-1, you should align with IEC 62443 and implement segmentation of the
control system. Relevant capabilities are firewalls, unidirectional communication,
DMZ. Oil and Gas customers should also see DNVGL-RP-G108 for guidance on
partitioning.
You should practice security by design, per IEC 62443-4-1, including layers of
security and detection. The module relies on overall network security design, as it
is only one component of what should be a defined zone or subnet.

Start Here MVI56E-FLN ♦ ControlLogix Platform
User Manual FA Control Network Ethernet Communication Module
Page 14 of 155 ProSoft Technology, Inc.
1.5 Installing the Module in the Rack
If you have not already installed and configured your ControlLogix processor and
power supply, please do so before installing the MVI56E-FLN module. Refer to
your Rockwell Automation product documentation for installation instructions.
Warning: You must follow all safety instructions when installing this or any other
electronic devices. Failure to follow safety procedures could result in damage to
hardware or data, or even serious injury or death to personnel. Refer to the
documentation for each device you plan to connect to verify that suitable safety
procedures are in place before installing or servicing the device.
After you have checked the placement of the jumpers, insert the MVI56E-FLN
into the ControlLogix chassis. Use the same technique recommended by
Rockwell Automation to remove and install ControlLogix modules.
You can install or remove ControlLogix system components while chassis power
is applied and the system is operating. However, please note the following
warning.
Warning: When you insert or remove the module while backplane power is on,
an electrical arc can occur. An electrical arc can cause personal injury or
property damage by sending an erroneous signal to your system’s actuators.
This can cause unintended machine motion or loss of process control. Electrical
arcs may also cause an explosion when they happen in a hazardous
environment. Verify that power is removed or the area is non-hazardous before
proceeding.
Repeated electrical arcing causes excessive wear to contacts on both the
module and its mating connector. Worn contacts may create electrical resistance
that can affect module operation.

MVI56E-FLN ♦ ControlLogix Platform Start Here
FA Control Network Ethernet Communication Module User Manual
ProSoft Technology, Inc. Page 15 of 155
1 Align the module with the top and bottom guides, and then slide it into the
rack until the module is firmly against the backplane connector.
2 With a firm, steady push, snap the module into place.
3 Check that the holding clips on the top and bottom of the module are securely
in the locking holes of the rack.
4 Make a note of the slot location. You must identify the slot in which the
module is installed in order for the sample program to work correctly. Slot
numbers are identified on the green circuit board (backplane) of the
ControlLogix rack.
5 Turn power ON.
Note: If you insert the module improperly, the system may stop working or may
behave unpredictably.
1.6 Installing ProSoft Configuration Builder
To install ProSoft Configuration Builder from the web site
1 Download the latest version of PCB from www.prosoft-technology.com.
2 Run the install file. This action starts the installation wizard for ProSoft
Configuration Builder.
3 Click NEXT on each page of the installation wizard. Click FINISH on the last
page of the wizard.

Start Here MVI56E-FLN ♦ ControlLogix Platform
User Manual FA Control Network Ethernet Communication Module
Page 16 of 155 ProSoft Technology, Inc.
1.7 Connecting Your PC to the Module
The E1 port is for configuration only and cannot be used on the FL-net network.
The E2 port is for exclusive use on the FL-net network and cannot be used for
configuration.
To configure the module, once it is securely mounted, connect one end of an
Ethernet cable to the Config (E1) port and connect the other end to an Ethernet
hub or switch which is accessible from the same network as your personal
computer (PC). You can also connect directly from the Ethernet port on your PC
to the Config (E1) port on the module by using an Ethernet crossover cable (not
included).

MVI56E-FLN ♦ ControlLogix Platform Start Here
FA Control Network Ethernet Communication Module User Manual
ProSoft Technology, Inc. Page 17 of 155
1.8 Setting Up a Temporary IP Address
Important: ProSoft Configuration Builder locates MVI56E-FLN modules through
UDP broadcast messages. These messages may be blocked by routers or layer
3 switches. In that case, ProSoft Discovery Service will be unable to locate the
modules.
To use ProSoft Configuration Builder, arrange the Ethernet connection so that
there is no router/layer 3 switch between the computer and the module OR
reconfigure the router/layer 3 switch to allow the routing of the UDP broadcast
messages.
1 Click the START button, and then navigate to PROGRAMS /PROSOFT
TECHNOLOGY.
2 Click to start ProSoft Configuration Builder.

Start Here MVI56E-FLN ♦ ControlLogix Platform
User Manual FA Control Network Ethernet Communication Module
Page 18 of 155 ProSoft Technology, Inc.
If you have used other Windows configuration tools before, you will find the
screen layout familiar. PCB’s window consists of a tree view on the left, and
an information pane and a configuration pane on the right side of the window.
When you first start PCB, the tree view consists of folders for DEFAULT
PROJECT and DEFAULT LOCATION, with a DEFAULT MODULE in the Default
Location folder. The following illustration shows the PCB window with a new
project.
3 Use the mouse to select DEFAULT MODULE in the tree view, and then click the
right mouse button to open a shortcut menu.

MVI56E-FLN ♦ ControlLogix Platform Start Here
FA Control Network Ethernet Communication Module User Manual
ProSoft Technology, Inc. Page 19 of 155
4 On the shortcut menu, select CHOOSE MODULE TYPE. This action opens the
Choose Module Type dialog box.
5 In the Product Line Filter area of the dialog box, select MVI56E. In the
SELECT MODULE TYPE dropdown list, select MVI56E-FLN, and then click OK
to save your settings and return to the ProSoft Configuration Builder window.
6 Right-click the module icon.
7 Click the SET UP CONNECTION button to browse for the module’s IP address.

Start Here MVI56E-FLN ♦ ControlLogix Platform
User Manual FA Control Network Ethernet Communication Module
Page 20 of 155 ProSoft Technology, Inc.
8 On the Connection Setup dialog box, click the TEST CONNECTION button to
verify if the module is accessible with the current settings
9 If PCB is still unable to connect to the module, click the BROWSE DEVICE(S)
button to open the ProSoft Discovery Service.
10 Select the module, then right-click and choose ASSIGN TEMPORARY IP.
11 The module’s default IP address is 192.168.0.250.
12 Choose an unused IP within your subnet, and then click OK.