protech YADA ST User manual

* Picture show YADA ST version

2
SNV: Service na verkoop
Alléén fabricagefouten of problemen veroorzaakt
door een fabricagefout zullen op rekening van de SNV
hersteld worden. Er kan nooit aanspraak gemaakt
worden op een gratis herstelling door de SNV als de
problemen voortkomen uit een verkeerd gebruik van
het produkt.
SAV INTERNATIONALE
PROTECH
TEL: ++ 32 14 25 92 83
FAX: ++ 32 14 25 92 89
email: [email protected]
http://www.protech.be
Om het zoeken van het onderdeel dat u nodig hebt te
vergemakkelijken, gelieve de onderdelenlijst op pagina
30-41 van deze handleiding te raadplegen
PROTECH kan niet verantwoordelijk gesteld worden
voor schade of vorderingen voortvloeiend uit het
gebruik van dit produkt
KD : Kundendienst
Nur Herstellungsfehler oder durch Herstellungsfehler
verursachte Probleme werden für Rechnung des KD
repariert. Die Garantie kann nicht in Anspruch genom-
men werden, wenn das Problem auf eine unsachge-
mäße Verwendung des Erzeugnisses zurückzuführen
ist.
SAV INTERNATIONALE
PROTECH
TEL: ++ 32 14 25 92 83
FAX: ++ 32 14 25 92 89
email: [email protected]
http://www.protech.be
Bitte verwenden Sie die in diesem Anweisungsheft auf
Seite 30-41 abgedruckten Diagramme, um die Ersatz-
teile zu finden, die Sie benötigen.
PROTECH kann nicht für Schäden oder Ansprüche
haftbar gemacht werden, die sich aus der Verwendung
dieses Produkts ergeben.
SAV: Service après vente
Ne seront pris en charge par le SAV, que les pièces
présentant un vice de fabrication. En aucun cas, la
mauvaise utilisation du produit ne peut enjendrer un
SAV gratuit.
SAV INTERNATIONALE
PROTECH
TEL: ++ 32 14 25 92 83
FAX: ++ 32 14 25 92 89
email: [email protected]
http://www.protech.be
Afin de faciliter la recherche de vos pièces détachées,
veuillez consulter la liste des pièces détachées en fin
de cette notice
PROTECH ne peut pas être rendu responsable pour
des dommages provenant de l’utlisation de ce produit.
SAS: Service after sales
Please note that only manufacturing faults or prob-
lems caused by manufactor faults will be repaired on
the account of SAS. It is not possible to claim warranty
if the problem is caused by misuse of this product.
SAV INTERNATIONALE
PROTECH
TEL: ++ 32 14 25 92 83
FAX: ++ 32 14 25 92 89
email: [email protected]
http://www.protech.be
Please use the spare parts list at the back of this
manual to help you find the part more easily
PROTECH cannot be held responsible for damage or
any claims arizing from the use of this product.
Service
version: YADA ST/PRO/PRO-X 10/08/2006

3
Performance features of the YADA 1/8th Nitro Buggy
YADA ST
YADA PRO
YADA PRO-X
Extreme low Differential Center Of Gravity
Extreme light Differential system
Increased suspension travel to 7cm
Pro steering geometry angle
Moulded wing and Body included
Lower CG design troughout the car
6061 Anodized Black Aluminium Radio Plate
6061 Anodized 3.2mm Alu main chassis
6061 Anodized Black steering plate
6061 engine mount set
6061 Black center diff. support plate
Pro Turnbuckles
3 Shoe clutch
Low profile radio box
Pro brake pad
Shock shaft of 3.5mm
Two Piece Pro center differential mount
Full ball Bearing throughout the car
Protech SX-21 engine included
Complete 2 Channel radio included
Laydown servo steering
CNC Spur, Crown and Pinion gear
Rear swaybar
Competition Dishweels & Tyres
7075 Lightened CNC design main chassis
7075 CNC RE & FR susp hinge pin holder
7075 CNC lightened design FR shocktower
7075 CNC lightened design RE shocktower
7075 CNC lightened steering plate
7075 CNC lightened Torque rod front & rear
7075 Black Center differential support plate
7075 Black CNC design Radioplate
Extra features
features
Extra “X” features
Reinforced brake pad & holder
7075 Engine mount set
Competition dish wheels & Tyres
Universal joints rear & front
1.7mm blue springs rear & front
Rear and Front swaybar
7075 CNC lightened FR shocktower black/chrome finished-X
7075 CNC lightened RE shocktower black/chrome finished-X
7075 CNC lightened Torque rod FR black/chrome finished-X
7075 CNC lightened Torque rod RE black/chrome finished-X
7075 CNC lightened FR suspension Arm holder black/chrome finished-X
7075 CNC lightened RE suspension Arm holder black/chrome finished-X
7075 Steering servo mount-X & Aluminium Wing stay joint
7075 Center diff mount set-X
7075 Engine mount set-X
7075 Sway bar plate-X
7075 Steering plate-X
7075 Radio plate-X
7075 center diff plate
Motor and radio equipment are not
included !
Motor and radio equipment are not
included !
* Picture show YADA ST version
T30
T31
T32
+,*+3(5)250$1&(:'
1,752%8**<

4
SPECIAL
PAINT FOR
POLYCARBONATE
Tools required / Benodigde gereedschappen
Benotigde werkzeuge / Outils recommandés
Conical reamer
Konische ruimer
Konische Reibahlen
Alésoir conique
Sharp hobby knife
Scherp hobbymes
Hobby messer
Couteau de modéliste
Needle nose plier
Bek tang
Beiszange
Pince à becs
Philips screw driver
Kruisschroevendraaier
Schraubendreher
Tournevis Philips
Hexwrench set
Inbussleutels set
Sechskant-Steckschlüssel
Set clés allen
Curved scissors
Gebogen schaar
Gebogene Schere
Ciseaux
Wire cutter
Draad stripper
Kneifzange
Pince coupante
Cross wrench
Kruissleutel
Clé en croix
Kreuzschlussel
Nut lock
Lock-Tide
Schrauben Sicherer
Frein-filet
Protech Racing Finish
Protech Racing Finish
Protech Racing Finish
Protech Racing Finish
AK101
T0158 4pcs
AK100
T0158
A600
RF... (*)
Check the colours in our
general catalog or visit
us at
http://www.protech.be

5
Engine set -up / Afstellen van de motor
Einstellungen des Motors / Réglage moteur
Afstellen motor • Einstellen des Motors • Réglage du moteur
.21-.27series
• Check the ENGINE SET-UP manual to start and break in the engine
• Lees aandachtig de handleiding AFSTELLEN MOTOR voor het inlopen en roderen van de motor
• Lesen Sie gründlich die Anleitung EINSTELLEN DES MOTORS für das einlaufen und rodieren vom Motor
• Consultez le manuel REGLAGE DU MOTEUR pour démarrer et rôder votre moteur

6

FRONT of REAR DIFFERENTIAL 2x
Assembly of the differentials FR & RE / Montage van het voorste en achterste differentielen /
Assemblage des différentiels AV et AR / Montierung von die Vordere und Hintere Differentialen
Differential gasket set
T30.091
Ball bearing
8x16x5mm
T30.144
Diff Case (F/R)
T30.034
2 x 9 mm pin
T30.103
Differential shaft
T30.075
Shim ring
3,6x12mm
T30.090
Bevel gear 39T
T30.068
2 x 9 mm pin
T30.103
Cap Joint
T30.055
Differential bevel gear 18T(Large)
T30.070
Differential bevel gear (Large)
T30.070
Cap Joint
T30.055
O-ring
T30.087
O-ring
T30.087
Shim ring
T30.089
Shim ring
T30.089
O-ring (option part)
T31.215
F/H 3mm x 10mm (4)
T30.180
Bevel gear small
T30.071
Differentials
Gear Differential / Make 2 x !
Assembly of the Front Differential
(*) USE ONLY PROTECH SILICONE OIL
F/H 3mm x 10mm (x4)
O-rings are a optional part for different driving settings (with O-rings = more acceleration)
OIL
OIL
! 90% Full / Plein / Vol / Voll
OIL (*)
Ball bearing
8x16x5mm
T30.144
FRONT DIFF. More steering use the ref. SL2500
Standard use the ref. SL5000
Less steering use the ref. SL10000
CENTER
DIFF.
Standard use the ref. SL5000
Quick use the ref. SL10000
acceleration
REAR DIFF. Standard use the ref. SL1000
or use grease

7

Assembly of the differentials RE & CE / Montage van de achterste en centrale differentielen /
Assemblage des différentiels AR et CE / Montierung von die Centale und Hintere Differentialen
FRONT DIFF. More steering use the ref. SL2500
Standard use the ref. SL5000
Less steering use the ref. SL10000
CENTER
DIFF.
Standard use the ref. SL5000
Quick use the ref. SL10000
acceleration
REAR DIFF. Standard use the ref. SL1000
or use grease
(*) USE ONLY PROTECH SILICONE OIL
OIL (*)
Differential gasket set
T30.091
Differential shaft
T30.075
Shim ring
3.6x12mm
T30.090
F/H 3mm x 10mm (4)
Bevel gear small 10T
T30.071
OIL
2 x 9 mm pin
T30.103
Cap Joint
T30.056
Differential bevel gear 18T (Large)
T30.070
Shim ring
T30.089
Diff Case (F/R)
T30.034
Cap Joint
T30.056
Center diff. gear 44T
T30.067
Shim ring
T30.089
2 x 9 mm pin
T30.103
Bevel gear large
T30.070
OIL
Assembly of the Rear Differential
Central Gear Differential
F/H 3mm x 10mm (x4)
O-ring
T30.087
O-ring
T30.087
! 90% Full / Plein / Vol / Voll
Ball bearing
8x16x5mm
T30.144
Ball bearing
8x16x5mm
T30.144

8


Assembly of the REAR gearbox & Center diff. / Montage v/d tandwielkast A & Centraal diff /
Montage des réducteurs AR & différentiel central/ Montierung des Getriebe A & Central
FRONT GEAR BOX
Rear Gear Box
Stud lock
A601
Nut lock
A600
F/H 3mm x 10mm (4)
T30.180
Differential gasket set
T30.091
Differential shaft
T30.075
NUT LOCK
90% Full / Plein / Vol / Voll
OIL (*)
O-rings are a optional part for different driving settings (with O-rings = more acceleration)
Bevel gear small
T30.071
O-ring (option part)
T31.215
Shim ring
3.6x12mm
T30.174
Set screw
5x5mm
T30.192
R/H 3 x 16mm
T30.213
Rear Sus. Hinge pin Holder ( * )
Drive Joint
T30.057
Shim ring
T30.088
Shim ring
T30.111
Pinion Gear Small
T30.069
Rear Toe In (use 3 degrees to start)
T30.048
Gearcase
T30.027
FH/ST 3 x 40mm
T30.184
F/H 3 x 20mm
T30.208
Gearcase
T30.027
Assembly of the Central Differential
FRONT DIFF. More steering use the ref. SL2500
Standard use the ref. SL5000
Less steering use the ref. SL10000
CENTER
DIFF.
Standard use the ref. SL5000
Quick use the ref. SL10000
acceleration
REAR DIFF. Standard use the ref. SL1000
or use grease
(*) USE ONLY PROTECH SILICONE OIL
F/H 3mm x 40mm (x2)
R/H 3mm x 16mm (x2)
Set Screw 5mm x 5mm (x1)
F/H 3mm x 10mm (x4)
*YADA ST = 6061 Alu Rear Sus. Hinge Pin Holder T30.084
YADA PRO = 7075 CNC Rear Sus. Hinge Pin Holder T31.213
YADA PRO-X = 7075 CNC Rear Sus. Hinge Pin Holder-X T31.239
High Speed Grease
SL001
8 x 16 x 5 mm
ball bearing
T30.144
Shim ring
T30.088

9
Front Gear Box
Assembly of the FRONT gearbox & SUSPENSION / Montage v/d tandwielkast V & / ophanging
Montage des réducteurs FR & de la Suspension AV / Montierung des Getriebe V & Querlenker V
5 x 5mm set screw
T30.192
F/H 3 x 15mm
T30.178
Front Toe In
(use 1 degree)
T30.048
Drive Joint
T30.057
Shim Ring
T30.088
Shim Ring
T30.111
Pinion Gear small
T30.069
F/H 3 x 20mm
T30.208
FH/ST 3 x 40mm
T30.184 Front Sus. Hinge Pin Holder ( * )
Gearcase
T30.027
Gearcase
T30.027
Front Body Mount
T30.046
Front Shock Tower ( * )
R/H 3 x 12mm
T30.212
E-Clip 3mm
T30.200
E-Clip 3mm
T30.200
Front Sus. Arm-R
T30.025
Front Sus. Arm-L
T30.025
Set Screw 4 x 8mm
T30.191
Set Screw 4 x 8mm
T30.191
Adjuster
T30.049
Front Shock Tower
Front Lower arm
Set Screw 4 x 8mm (x2)
*YADA ST = 6061 Alu Front Shock Tower T30.078
YADA PRO = 7075 Lighten CNC Front Shock Tower T31.204
YADA PRO-X = 7075 Lighten CNC Black/Chrome design
Front Shock Tower-X T31.205
NUT LOCK
High Speed Grease
SL001
Front Lower Susp. Hinge Pin
T30.072
8 x 16 x 5 mm
ball bearing
T30.144
*YADA ST = 6061 Alu Front Sus. Hinge Pin Holder T30.083
YADA PRO = 7075 CNC Front Sus. Hinge Pin Holder T31.212
YADA PRO-X = 7075 CNC Front Sus. Hinge Pin Holder-X T31.238

10


Assembly of the front suspension / Montage van de voorste ophanging /
Montage de la suspension avant / Montierung von die vordere Querlenker
Make sure that the swaybare can move freely
Distance between the 2 ball Ends = 0.5mm
Front Upper Sus. Plate ( * )
MAKE 4 SETS !
Stabilizer Ball
T30.100
Ball End 6mm
T30.051
3 x 12mm
T30.188
Ball 6mm
T30.102
3 x 3mm
T30.186
NUT LOCK
3 x 3mm
T30.186
NUT LOCK
R/H 3 x 16mm
T30.213
R/H 3 x 16mm
T30.213
3 x 5mm
F/H 3 x 8mm
T30.204
Sway Bar Plate (*)
T30.104 * Sway Bar Front
Not Included in YADA ST
Front Upper Sus. Hinge Pin Holder-R
T30.043
Front Upper Sus. Hinge
Pin Holder-L
T30.043
Front Sway Bar
Front Upper Suspension Plate
R/H 3 x 8mm
T30.210
R/H 3mm x 8mm (x4)
3mm x 3mm (x2)
3mm x 5mm (x2)
R/H 3mm x 16mm (x2)
F/H 3mm x 8mm (x2)
YADA ST = 6061 Alu Front Upper Sus. Plate T30.080
YADA PRO = 7075 Black anodized CNC plate T31.208
YADA PRO-X = 7075 Black/chrome anodized CNC plate-X T31.209
Nylon Nut M3
T30.172
YADA PRO = 7075 Sway Bar Plate T31.217
YADA PRO-X = 7075 Sway Bar Plate T31.235
Front Sway Bar 2.2mm : T30.105
2.3mm : T30.106
2.4mm : T30.107
Stud lock
A601
Nut lock
A600
*
*
*