PureEdge Lighting TruTrack TR24-CP1-1RE WH Series User manual

SAVE THESE INSTRUCTIONS!
- This product is for indoor locations only.
- This instructions shows a typical installation.
- Before beginning any electrical work, ensure that the
power to the electrical box is off.
IMPORTANT INFORMATION
1718 W. Fullerton Chicago, IL 60614
Ph: 773.770.1195 ● Fax: [phone]
www.PureEdgeLighting.com ● [email protected]
© 2016 PureEdge Lighting. All Rights Reserved.
Doc # 904-TR24-CP1-1RE_02
Installation Instructions for TruTrack Center Power Feed with
1" Rectangle Junction Box
TR24-CP1-1RE-_-_-WH
Section One: Install the Junction Box
1
1: Mount each adjustable mounting bar to one side of the junction box and secure them with the mounting brackets and
Phillips screws provided.
A
B
ADJUSTABLE
MOUNTING BAR
#8 SCREWS
ADJUSTABLE
MOUNTING BAR
CONDUIT
3
2
MOUNTING
BRACKET
PHILLIPS SCREW
JUNCTION BOX
1
PHILLIPS SCREW
1
MOUNTING
BRACKET
ADJUSTABLE
MOUNTING BAR
JUNCTION BOX
HORIZONTAL ORIENTATION VERTICAL ORIENTATION
NOTE: Only use 0-10V and Uni power supplies with this
product. See the wiring diagram provided with the power supply
instructions.
2: Place the adjustable mounting bar tabs against the ceiling
joists. Secure the adjustable bars to the joists with the #8
screws.
3: Install conduit (if required by local electrical code) and run
the low voltage wires coming from the remote power supply
to the junction box.
NOTE: Adjustable mounting bars mount to studs that are
spaced 14.5" to 25" apart.
INSTALLATION
DIRECTION
INSTALLATION
DIRECTION

1: Cut a section of drywall to expose the junction box area.
Install the drywall.
2: Mark and cut out the area where the installation will be
located using the junction box opening as a guide.
C
CUT
TRACK WITH COVER
INSTALLATION LENGTH
INSTALLATION
DIRECTION NOTE: Refer to the TruTrack Recessed Channel instructions to
measure and cut the track and cover before continuing.
Section Two: Install 1RE Center Power Feed
INSTALLATION
DIRECTION
3: Align and slide tracks over the straight connectors on the
ends of the Center Power Feed. Tighten the set screws using
an Allen wrench and the slotted screw on the straight
connector using a flat-head screw driver.
D
3
CENTER
POWER
FEED TRACK
SET
SCREW
STRAIGHT
CONNECTOR
4: Secure the Center Power Feed to the junction box with the #4-40 screw using a 1/16" Allen wrench.
5: Secure the track to the ceiling using drywall screws.
E
5
DRYWALL
SCREW
4
2
1
2
DRYWALL

3
F 6: Strip 3/8" off of the Power Feed Adapter wires and the
low voltage power supply wires.
7: Pull up the levers of one lever nut and insert the low voltage
+24VDC power supply wire and the red wire of the Power
Feed Adapter into the lever nut. Push the lever down to
connect and lock into place.
8: Pull up the levers of the other lever nut and insert the low
voltage -24VDC power supply wire and the black wire of the
Power Feed Adapter into the lever nut. Push the lever down
to connect and lock into place.
9: Lightly tug on the wires to ensure they are secured in place.
10: Place the lever nut connections inside the junction box.
11: Place the Power Feed Adapter inside the Center Power Feed
and tighten the slotted screw with a flat-head screw driver
to secure in place.
NOTE: Refer to the TruTrack Recessed Channel instructions to
plaster and complete the installation.
LEVER NUT
3/8"
6
LEVER
POWER FEED
ADAPTER
11
8
7