PureEdge Lighting TruTrack TR24-LP1-1RE WH Series User manual

SAVE THESE INSTRUCTIONS!
- This product is for indoor locations only.
- This instructions shows a typical installation.
- Before beginning any electrical work, ensure that the
power to the electrical box is off.
IMPORTANT INFORMATION
1718 W. Fullerton Chicago, IL 60614
Ph: 773.770.1195 ● Fax: [phone]
www.PureEdgeLighting.com ● [email protected]
© 2016 PureEdge Lighting. All Rights Reserved.
Doc # 904-TR24-LP1-1RE-_03
Installation Instructions for TruTrack L-Shaped Power Feed
with 1"Rectangle Junction Box
TR24-LP1-1RE-_-_-WH
Section One: Install the Junction Box
1
1: Mount each adjustable mounting bar to one side of the junction box and secure them with the mounting brackets and
Phillips screws provided.
A
B
ADJUSTABLE
MOUNTING BAR
#8 SCREWS
ADJUSTABLE
MOUNTING BAR
CONDUIT
3
2
MOUNTING
BRACKET
PHILLIPS SCREW
JUNCTION BOX
1
1
MOUNTING
BRACKET
ADJUSTABLE
MOUNTING BAR
JUNCTION BOX
NOTE: Only use 0-10V and Uni power supplies with this
product. See the wiring diagram provided with the power supply
instructions.
2: Place the adjustable mounting bar tabs against the ceiling
joists. Secure the adjustable bars to the joists with the #8
screws.
3: Install conduit (if required by local electrical code) and run
the low voltage wires coming from the remote power supply
to the junction box.
NOTE: Adjustable mounting bars mount to studs that are
spaced 14.5" to 25" apart.
PHILLIPS SCREW
INSTALLATION
DIRECTION
INSTALLATION
DIRECTION

1: Cut a section of drywall to expose the junction box area.
Install the drywall.
2: Mark and cut out the area where the installation will be
located using the junction box opening as a guide.
C
CUT
TRACK WITH COVER
INSTALLATION LENGTH
2
3: Align and slide tracks over the straight connectors on the
ends of the L-Shaped Power Feed. Tighten the set screws
using an Allen wrench and the slotted screw on the straight
connector using a flat-head screw driver.
D
4: Secure the L-Shaped Power Feed to the junction box with the two #4-40 screws using a 1/16" Allen wrench.
5: Secure the track to the ceiling using drywall screws.
E
Section Two: Install 1RE L-Shaped Power Feed
DRYWALL
SCREW
5
STRAIGHT
CONNECTOR
L-SHAPED
POWER
FEED
TRACK
TRACK
3
3
4
4
2
#4-40
SCREW
INSTALLATION
DIRECTION
INSTALLATION
DIRECTION
NOTE: Refer to the TruTrack Recessed Channel instructions to
measure and cut the track and cover before continuing.
1
1
L-SHAPED
POWER TRACK
SET
SCREW
STRAIGHT CONNECTOR

F
7
6: Strip 3/8" off of the Power Feed Adapter wires and the low
voltage power supply wires.
7: Pull up the levers of one lever nut, and insert the low
voltage +24VDC power supply wire and the red wire of the
Power Feed Adapter into the lever nut. Push the lever down
to connect and lock into place.
8: Pull up the levers of the other lever nut and insert the low
voltage -24VDC power supply wire and the black wire of the
Power Feed Adapter into the connector. Push the lever down
to connect and lock into place.
9: Lightly tug on the wires to ensure they are secured in place.
WAGO
CONNECTOR
3/8"
6
LEVER
8
POWER FEED
ADAPTER
10: Place the lever nut connections inside the junction box.
11: Place the Power Feed Adapter inside the L-Shaped Power
Feed and tighten the slotted screw with a flat-head screw
driver to secure in place.
NOTE: Refer to the TruTrack Recessed Channel instructions to
plaster and complete the installation.
G
11
3