Puretec TSI Series User manual

User Guide
For correct operation & installation, it is essential to observe these instructions.
AUG2021
Stainless Steel Water Filtration Housings
TSI / TSI-MP Series

2 Installation & Operation Manual Copyright © Puretec Pty Ltd 2021
Puretec Customer Service
Thank you for purchasing a Puretec water lter housing. Your housing is a proven
performer manufactured from only quality materials and components and will give
years of ‘spring fresh’ water free of impurities if maintained properly.
The housing can be used in a wide variety of applications and is compatible with a
wide range water lter cartridges (sold separately). Select a cartridge that best suits
your situation/water source. For cartridge selection advice contact your local Puretec
dealer or call our Puretec Customer Service Helpline.
With a sediment lter some features include:
• Supply clean water to kitchen, bathroom and laundry.
• Extends the life of appliances by removing silt, rust etc protecting hot water
systems, washing machines, dishwashers, solenoid garden valves, tap washers,
ceramic disc mixer taps and thermostatic valves.
• Minimises build-up in pipework and reduces repair costs.
With a taste and odour removal lter you will:
• Provide healthy, clean and pure water for all household drinking, cooking and
showering needs.
What's Inside
What's Inside
Introduction................................................................................................................................. 2
Guidelines and Warnings..................................................................................................... 3
Fig. 1 Diagram TSI Models.................................................................................................. 4
Fig. 2 Diagram TSI-MP Models......................................................................................... 5
Fig. 3 Dimensions TSI Models........................................................................................... 6
Fig. 4 Dimensions TSI-MP Models .................................................................................. 7
Model Information................................................................................................................... 8
Positioning Your Filter......................................................................................................... 10
Installation Procedure ........................................................................................................ 10
Fig. 5 & 6 Typical Installation........................................................................................ 11
Fig. 7 Cutaway Diagrams ................................................................................................. 12
Replacement Guide.............................................................................................................. 13
Cartridge Installation / Replacement ......................................................................... 13
Warranty .................................................................................................................................... 15

3
TSI / TSI-MP Series Water Filtration Housings
Guidelines & Warnings
• Have better tasting beverages, tea, coee, drinking water and ice.
• Safe water to drink, free from harmful chemicals - also safe for baby formulas.
• Chemicals absorbed by the skin can be removed for use in the shower.
The Puretec lter housing cartridges need replacing regularly to maintain optimum
performance. Replace cartridges when water ow is reduced, taste or odour returns
to water (carbon cartridges only) or every 6 to 12 months. For cartridge replacements
contact your nearest Puretec stockist.
Customer Service Helpline 1300 140 140 (Australia) 0800 130 140 (New Zealand).
Guidelines and Warnings
• If pressure exceeds max pressure, an approved pressure limiting device needs to
be tted. If water hammer is present, t a hammer arrestor close to the source of
the hammer. Note: Check local plumbing regulations and any installed plumbing
xtures for specic kPa limits required below the stated Max Pressure of this
product .
• Suitable for use on cold and hot water lines up to a maximum of 75°C. Protect the
housing from freezing.
• For point of entry installations an approved dual check backow prevention device
must be tted in accordance with national plumbing product codes.
• Do not use with water that is microbiologically unsafe or with water of unknown
quality without adequate disinfection.
• This product must be installed in accordance with local plumbing regulations by a
licensed plumber.
Installation Note: A water lter system/tap, like any product, has a limited life
and may eventually fail. Also sometimes failure happens early due to unforeseen
circumstances. To avoid possible property damage, this product should be regularly
examined for leakage and/or deterioration and replaced when necessary. A drain pan,
plumbed to an appropriate drain or outtted with a leak detector, should be used in
those applications where any leakage could cause property damage, and/or the water
supply should be turned o if no one is home/present.
INSTALLATION MUST BE COMPLETED BY A LICENCED PLUMBER. FAULTY
OPERATION DUE TO UNQUALIFIED PERSONS WILL RESULT IN VOIDED
WARRANTY COVERAGE.

4 Installation & Operation Manual Copyright © Puretec Pty Ltd 2021
Fig. 1 - Diagram - TSI Models
Clamp
Housing Head
O-ring
Cartridge Rod
Cartridge Guide
Nut
Mounting Bracket
20" x 2.5"
Housing Bowl
Clamp
Housing Head
O-ring
Cartridge Rod
Cartridge Guide
Nut
Mounting Bracket
10" x 2.5"
Housing Bowl
Diagram
Drain
Drain

5
TSI / TSI-MP Series Water Filtration Housings
Fig. 2 - Diagram - TSI-MP Models
Clamp
Housing Head
Gasket
Cartridge Rod
Cartridge Guide
Nut
Mounting Bracket
10" x 4.5"
Housing Bowl
Vent
Clamp
Housing Head
Gasket
Cartridge Rod
Cartridge Guide
Nut
Mounting Bracket
20" x 4.5"
Housing Bowl
Vent
Cartridge Guide
Diagram
Drain
Drain

6 Installation & Operation Manual Copyright © Puretec Pty Ltd 2021
127
494
747
127
106
645
106
395
Fig. 3 - Dimensions - TSI Models
Dimensions
TSI-151, TSI-201
& TSI-251
TSI-252

7
TSI / TSI-MP Series Water Filtration Housings
127
494
747
127
106
645
106
395
Fig. 4 - Dimensions - TSI-MP Models
Dimensions
TSI-25MP1 TSI-25MP2

8 Installation & Operation Manual Copyright © Puretec Pty Ltd 2021
Model: TSI-151 TS1-201 TSI-251
Operating Pressure Min/Max: 200 - 1034 kPa
Operating Temperature Min/Max: 0 - 75 °C (protect from freezing)
Inlet/Outlet Connection: ½" BSPT ¾" BSPT 1" BSPT
Vent Connection: ¼" BSPT
Drain Connection: ¼" BSPT
Material: 304
Dimensions: 106 (W) x 395 (H) mm
Cartridge Size: 2.5" x 10"
TSI 10" Model Information
Specications
ORDER CODE DESCRIPTION
TSI-CLMP Replacement clamp, suits TSI-151, TSI-201, TSI-251 and
TSI-252
TSI-OR Replacement O-ring, suits TSI-151, TSI-201, TSI-251 and
TSI-252
Replacement Parts
Model: TSI-252
Operating Pressure Min/Max: 200 - 1034 kPa
Operating Temperature Min/Max: 0 - 75 °C (protect from freezing)
Inlet/Outlet Connection: 1" BSPT
Vent Connection: ¼" BSPT
Drain Connection: ¼" BSPT
Material: 304
Dimensions: 106 (W) x 645 (H) mm
Cartridge Size: 2.5" x 20"
TSI 20" Model Information
Specications
Model Information

9
TSI / TSI-MP Series Water Filtration Housings
Model: TSI-25MP1
Operating Pressure Min/Max: 200 - 1034 kPa
Operating Temperature Min/Max: 0 - 75 °C (protect from freezing)
Inlet/Outlet Connection: 1" BSPT
Vent Connection: ¼" BSPT
Drain Connection: ¼" BSPT
Material: 304
Dimensions: 127 (W) x 494 (H) mm
Cartridge Size: 4.5" x 10"
TSI-MP 10" Model Information
Specications
ORDER CODE DESCRIPTION
TSIMP-CLMP Replacement clamp, suits TSI-25MP1 and TSI-25MP2
TSIMP-OR Replacement gasket, suits TSI-25MP1 and TSI-25MP2
Replacement Parts
Model: TSI-25MP2
Operating Pressure Min/Max: 200 - 1034 kPa
Operating Temperature Min/Max: 0 - 75 °C (protect from freezing)
Inlet/Outlet Connection: 1" BSPT
Vent Connection: ¼" BSPT
Drain Connection: ¼" BSPT
Material: 304
Dimensions: 127 (W) x 747 (H) mm
Cartridge Size: 4.5" x 20"
TSI-MP 20" Model Information
Specications
Model Information

10 Installation & Operation Manual Copyright © Puretec Pty Ltd 2021
Positioning Your Filter
Positioning Your Filter
Choose a location where any water spillage will not cause damage. If a cupboard
is chosen care needs to be taken in case of water spillage or ooding. Make sure
mounting position is solid so that the lter housing stays in position when changing
lters. An isolation valve may be installed immediately prior to the lter to isolate the
lter for changing the cartridge.
Installation Procedure
1. Isolate water supply and relieve pressure by opening a downstream tap.
2. Cut pipe to suit length of required valve and housing installation.
3. Use approved brass, galv/poly plumbing ttings to suit existing pipework. The
female threads on the housing will receive tapered male threads. Thread into
housing head carefully and tighten rmly.
5. Securely x the mounting bracket and pipework with suitable clips. Allow enough
clearance under (above for TSI-MP models) the housing bowl for lter changes.
6. Flush debris from pipework.
7. Install lter cartridge as per cartridge replacement instructions.
Connecting
Pipework