PUTCO MOLLE PANELS RAM 1500 Manual

`DESCRIPTION QTY
Molle Front Plate 1
Molle Side Plates 2
Front Upper Brackets 2
Front Lower Brackets 2
Single-Flange Side Mounting Brackets 4
Double-Flange Side Mounting Brackets 4
M6 Torx-Head Bolt 32
Rubber Feet 3
Jam Nuts 3
5/16” Well Nut 16
3/4” Well Nut 2
3/8”-16 X 1.5” Allen Head Bolt 2
8-32 X 3/4” Philip’s Head Screw 16
5/16”-18 X 2 3/8” Allen Head Bolt 2
In-Bed Washer 2
Nut Plate 2
Congratulations on your purchase of a high quality PUTCO®product. Should
you need any application or technical assistance, feel free to call us at:
Monday-Friday 8:00am - 5:00pm (Central Standard Time)
Contact your PUTCO®dealer for other quality accessories.
1952XXI
1-800-247-3974
PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
AND CHECK TO SEE THAT ALL PARTS ARE INCLUDED
CONTENT LIST
REQUIRED TOOLS
INSTRUCTION GUIDE
RAM 1500
3/16” HEX KEY
7/32” HEX KEY
10MM WRENCH
PHILLIPS SCREWDRIVER
T30 TORX DRIVER

MOLLE Panels Instruction Guide
1
2
Begin by gathering all four of the Single-Flange Side Mounting Brackets and all four of the
Double-Flange Side Mounting Brackets.
Loosely assemble two 5/16” Well Nuts and two Philip’s Head Screws onto each of these brackets
as shown.
INSTALLATION INSTRUCTIONS
1952XXI
3Your Light-Duty Ram has hex-shaped holes in the bedsides that will be used to mount the Molle
Side Plates. The Double-Flange Brackets mount to the middle sets of holes, and the Single-
Flange Brackets mount to the outer sets of holes, as shown. Fasten the brackets to the bed by
inserting the Well Nuts into the hex-shaped holes, then tighten the Philip’s Head Screws until the
Well Nuts are snug in the hex-shaped holes, but do not overtighten.
Single-Flange Bracket Double-Flange Bracket

MOLLE Panels Instruction Guide
5
6
Install the Front Upper Bracket assemblies by
inserting the Nut Plate into the slot located
towards the top of each bed side as shown in
the pictures below. The nut plate will have to
be inserted at an angle in order to fit. During
this process, use caution so you do not loosen
the nut plate and drop it behind the slot! Next,
orient the nut plate so that it is perpendicular
and centered behind the slot, then push the
tabbed washer against the bed side so that
the tabs fit into the slot. If aligned correctly,
the tabs should prevent the nut plate from
spinning. While keeping the tabbed washer
in the slot, pull back on the bolt and begin to
tighten until snug, but do not fully tighten,
as the position of the bracket may need to be
adjusted. Perform this step for both driver and
passenger side.
Next, locate the two remaining Front Lower Brackets. Loosely assemble a 3/4-inch well nut and
1.5-inch long Allen head bolt onto each bracket. Install the lower bracket assemblies by inserting
the well nut into the slot located just next to the forward tie-down hook. Tighten the bolt using
a 7/32 hex key until the well nut is snug in the slot, but do not overtighten. Once all brackets are
installed, the bed of your Ram should look like the picture on the next page.
1952XXI
4Next, gather the two Front Upper Brackets.
Loosely assemble one 2-3/8” long Allen head
bolt, In-Bed Washer, and Nut Plate onto each of
these brackets.
Front Upper Bracket
Front Lower Bracket

MOLLE Panels Instruction Guide
1952XXI
Your new MOLLE Panels are now
successfully installed on your
vehicle!
7
8
9
10
Next, prepare the Molle Front Plate to be installed. Thread a jam nut onto each of the rubber feet,
then loosely screw the rubber feet into the riv nuts located on the bottom flange of the front
plate.
Fasten all three molle plates to their brackets using the provided Torx-head screws and a T30 Torx
driver.
Screw the rubber feet in the front plate down until they are snug against the bed floor, then lock
the feet in place by tightening the jam nut against the front plate using a 10mm wrench.
Now that everything is installed, ensure that all fasteners have been tightened until snug, but do
not overtighten.
Light Duty Ram with All Brackets Installed
Completed Molle Panel kit for Light Duty Ram