PUTCO 92100 User manual

92100, 92200
LIMITED 90 DAY WARRANTY
Putco guarantees it’s Stainless Steel and Aluminum products against defects in workmanship and material for as long as you
own your vehicle. All painted products have a 90 day warranty on the painted surface. Any defects resulting from faulty
material or workmanship will be warranted by Putco and repaired or replaced at our discretion. Putco assumes no extra labor
costs. Damages caused by freight carriers, improper installation, misuse, collision, or neglect will not be warranted by Putco.
8/25/16- CPH 92100I
Figure 1.1
2009-2014 Ford F-150 Ford Emblem Installation
Congratulations on your purchase of a high quality PUTCO product. Should you
need any application or technical assistance, feel free to call us at: 1-800-357-9261
Monday-Friday 8:00 a.m. - 5:00 p.m. (Central Standard Time)
Contact your PUTCO dealer for other quality accessories.
Please read all instructions before installation and to check to see that all parts are included.
Front Emblem Installation
1. Remove Emblems from packaging. Check to
see if all parts from above kit contents table are
included.
2. Open hood, Remove two 10mm nuts and that
secure the emblem to the hood. Shown in figure
1.1
3. Unclip the two shafts that held the two 10mm
nuts but gently pushing upwards on them and
pulling the emblem off the grille.
4. Install the provided threaded shafts into the back of the new emblem by hand until
shafts bottom out in emblem.
5. Install the emblem into the grille and finish the installation by installing the
washers and tightening the lock nuts using a 3/8” socket and ratchet. Be careful not
to over tighten the fasteners and damage the surrounding grille
KIT CONTENTS: 92100
Description
Qty.
Medium Ford Emblem
2
Bolt Kit
1
KIT CONTENTS: 92200
Medium Ford Emblem
1
Small Ford Emblem
1
3M Ford Emblem Tape
1
Bolt Kit
1
Alcohol Pad Packet
1
Tools Needed:
- 3/8” Ratchet
- 10mm and 3/8” Socket
- 3/8” Wrench
- Needle Nose Pliers
- Flat Blade Screwdriver
- T-30 Torx Bit (92100 only)

92100, 92200
LIMITED 90 DAY WARRANTY
Putco guarantees it’s Stainless Steel and Aluminum products against defects in workmanship and material for as long as you
own your vehicle. All painted products have a 90 day warranty on the painted surface. Any defects resulting from faulty
material or workmanship will be warranted by Putco and repaired or replaced at our discretion. Putco assumes no extra labor
costs. Damages caused by freight carriers, improper installation, misuse, collision, or neglect will not be warranted by Putco.
8/25/16- CPH 92100I
Figure 2.1
Figure 3.1
Figure 3.2
Rear Emblem Installation Kit: 92100
1. Lower tailgate and remove the 13 T-30 screws holding the plastic tailgate protector
marked in figure 2.1
2. Remove the protector
3. Locate and remove the two
10mm screws holding the rear
emblem on
4. Unclip the two shafts that held
the two 10mm nuts but gently
pushing upwards on them and
pulling the emblem off the
tailgate
5. Install the provided threaded shafts into
the back of the new emblem by hand
until shafts bottom out in emblem.
6. Install the emblem into the tailgate and
finish the installation by installing the
washers and tightening the lock nuts
using a 3/8” socket and ratchet. Be
careful not to over tighten the fasteners
and damage the tailgate.
Rear Emblem Installation Kit: 92200
1. Gently pry against the smaller part of the
emblem shown in figure 3.1. Be careful not to
damage either part of the emblem
2. Set the factory emblem off to the side. Prep the
new emblem and the truck with the alcohol pad
3. Peel one side of the 3M tape and install it on the emblem. Center on emblem and
apply pressure. Figure 3.2 shows an example of properly positioned 3M tape.
4. Remove the other side of the 3M tape from the emblem and position the emblem on
the truck. Once the position is finalized, press firmly on the emblem against the truck
for 30 seconds.
Note: PUTCO recommends applying a high quality automotive wax to maintain the
original appearance on your new Ford Emblems