Pyronix Enforcer 32WE User manual

INTERNAL SIREN WARNING
The Enforcer 32-WE control panel
contains a 100 dBA siren,
please be aware of this during
installation
Programming Reference Manual
Wireless Alarm System
RINS1707-1
EN50131-1:2006+A1:2009
EN50131-3:2009
EN50131-6:2008
EN50131-5-3:2005+A1:2008
Security Grade 2
Environmental Class II
Software Version >10

Page: 2
1. Contents page
1. Contents page .................................................................................................................... 2
2. Introduction ....................................................................................................................... 3
2.1 Two Way Wireless High Security ....................................................................................... 3
2.2 Battery Monitoring/Saving ............................................................................................... 3
2.3 Pyronix Cloud and Home Control+ App .............................................................................. 4
3. Writing Texts on the keypad ................................................................................................. 5
4. The Engineer Menu.............................................................................................................. 5
4.1 Navigating in the Engineer and User Menus ........................................................................ 5
4.2 Entering The Engineer Menu (Default Engineer Code = 9999) ............................................... 6
4.3 Exiting The Engineer Menu............................................................................................... 6
4.4 Accessing the Engineers Menu on any external wired keypad ................................................ 6
4.5 Saving The Programming................................................................................................. 6
5. Engineer Menu.................................................................................................................... 6
5.1 Date and Time? .............................................................................................................. 6
5.2 Learn Wireless Devices? .................................................................................................. 7
5.3 Program Inputs?............................................................................................................11
5.4 Install RIXs? .................................................................................................................13
5.5 Program Outputs?..........................................................................................................13
5.6 Install Keypads and Readers? ..........................................................................................16
5.7 Program Timers? ...........................................................................................................17
5.8 Change Codes? .............................................................................................................19
5.9 Volume Control? ............................................................................................................20
5.10 System Options?..........................................................................................................21
5.11 Review Logs? ..............................................................................................................23
5.12 Engineer Tests? ...........................................................................................................23
5.13 Diagnostics?................................................................................................................24
5.14 Engineer Restore Options? ............................................................................................26
5.15 Communications?.........................................................................................................26
5.16 Alarm Responses?........................................................................................................30
5.17 Options Up/Downloading? .............................................................................................32
5.18 PC Connect Menu? .......................................................................................................32
5.19 Software Revision?.......................................................................................................33
5.20 Factory Default? ..........................................................................................................33
5.21 Exit Engineer Menu?.....................................................................................................33
6. Adding External Wired Keypad .............................................................................................33
7. Connecting to InSite Software..............................................................................................34
8. Options Programmable Only From PC....................................................................................36
8.1 Auto Arm/Disarm Timers ................................................................................................36
8.2 Areas to Arm/Disarm .....................................................................................................36
8.3 Programming Logic Gates ...............................................................................................37
9. Faults and Troubleshooting..................................................................................................38
9.1 Device Fail / Active Faults ...............................................................................................38
9.2 System Faults and Troubleshooting ..................................................................................38
10. Event Types ....................................................................................................................41
11. EN 50131 Terminology ......................................................................................................41
12. Access Levels...................................................................................................................41
13. Factory Defaults...............................................................................................................42
14. Event Types (SIA and Contact ID codes)..............................................................................46
15. Notes. ............................................................................................................................50

Page: 3
2. Introduction
2.1 Two Way Wireless High Security
The Enforcer 32-WE is a wireless alarm system that has been designed with a customer's security in
mind; with quick and easy installation and minimal maintenance, the Enforcer 32-WE protects a
property with a multitude of unique features.
Taking full advantage of Pyronix’s innovative two way wireless technology, the wireless devices on the
Enforcer 32-WE are constantly communicating with each other, using the Pyronix High Security
Wireless Encryption Protocol.
The Enforcer 32-WE two way wireless devices are fully operational when the system is armed, making
the system more secure, compared to other wireless systems, where devices are disabled for up to
five minutes after every activation to save battery, therefore compromising the security.
The Enforcer 32-WE has been engineered by Pyronix as a secure, reliable and easy to use wireless
alarm system. It includes the following features below:
2.2 Battery Monitoring/Saving
The Enforcer 32-WE uses advanced technology to preserve the battery life of each wireless device.
However, the Enforcer 32-WE indicates when a battery needs replacing a month in advance before
the device stops working. This key feature gives enough time to change the battery in the specific
device. Other wireless alarm systems may not give a low battery warning signal, meaning that
devices could stop working, leaving the environment unprotected.
2.2.1 High Security Encryption
128 bit high security wireless encryption protocol, and intelligent wireless jamming detection.
2.2.2 User Friendly Keyfobs
The fully two way wireless keyfob indicates the status of the control unit via 3 colour LEDs:
System armed: When the system is armed a RED LED will illuminate momentarily
System disarmed: When the system is disarmed a GREEN LED will illuminate momentarily
System fault: When the system is in fault condition an AMBER LED will illuminate momentarily,
This will also flash when the keyfob is unable to arm the system.
It is possible to allocate different functions to each keyfob such as arming / disarming different
areas, activating outputs to control external devices such as gates, requesting system status, and
activating panic alarms. Up to 32 wireless keyfobs can be added to the Enforcer 32-WE. Each
wireless keyfob has its own user ID which can be reported to the ARC and user mobile phone which
are stored into the event log of the control panel individually.
The keyfob also allows the arming/disarming of every area individually, giving total control of the
Enforcer 32-WE.
2.2.3 User Automation Outputs
The Enforcer 32-WE includes user automation outputs that gives the option to operate up to 20
devices such as gates, lights, sprinklers, etc. via the keypad or remotely via a Keyfob, thus
extending the use of the Enforcer-32-WE.
2.2.4 SMS Text Notifications and Remote Control
The system will notify via SMS text messages in real time. For example; notification that someone
has returned home safely or notification of a leakage of water in a property etc.

Page: 4
2.3 Pyronix Cloud and Home Control+ App
The Pyronix+ App turns a smartphone into a remote keypad. It can be used to:
- Arm / Disarm the Enforcer 32-WE;
- Activate the automation outputs to remotely turn on / off lights, open gates and so on;
- View real time sensor status and bypass sensors when required;
- View any notifications and event memory log;
- Receive push notifications from a system.
The Pyronix+ App and Pyronix Cloud communication is fully encrypted to the highest standard (AES
256) and no sensitive user data is stored on the Pyronix Cloud.
The Pyronix+ App is available in 2 versions Android from Google Play Store and iOS from Apple store.
www.pyronixcloud.com

Page: 5
3. Writing Texts on the keypad
On the Enforcer 32-WE it is possible to label the following:
-Inputs – 2 labels: Input Number and Location
-Area Names
-Site Name
-Keypad/Reader – 2 labels: Keypad Number and Location
-Input and Output expander location descriptions
-User Names
The Enforcer 32-WE incorporates a predictive text feature (T9 type). For example, enter ‘B’ and
‘Bedroom’ will be displayed. If the word that is required doesn’t appear, then type the word letter by
letter.
To type a word, press the relevant button the appropriate number of times – e.g. for the letter ‘k’
press 5two times, or for the letter ‘s’ press 7four times. For punctuation marks, press the 1
button multiple times until the desired character is shown.
Button meanings:
The following alpha-numerical buttons are used Other meaning of the buttons
a= makes the character into a capital a= Status Area A
c= clears letters / adds a space
b
= Status Area B
[= moves cursor left
c
= Status Area C
]= moves cursor right
d
= Status Area D
d
= Press to Enter Master Manager Mode
f
= Press for 2 sec to generate Fire alarm
p
= Press for 2 sec to generate PA alarm
4. The Engineer Menu
The system is programmed from the Engineer Menu. To enter the Engineer Menu the panel must be in
a disarmed state. Whilst in Engineer Mode all tamper alarms (including case tamper), will be disabled.
4.1 Navigating in the Engineer and User Menus
x= “NO” - Press to move forward when in Engineer or Master Manager mode
b= “BACK” - Press to move backward when in Engineer or Master Manger mode
t= “YES” - Press to enter in a submenu or option when in Engineer or Master Manger mode
t= Press to move from one option into another option while in a submenu
a= Press to quick exit the Engineer Menu from any main menu (written in capital letters)
c= “CANCEL” - Press to move back from one programmable option to the previous option.
4.1.1 Main Menus and Sub Menus
A Main Menu item is identified by:
The maintenance LED is flashing slowly
The menu item will be in capital letters
A Sub-Menu is identified by:
The maintenance LED is flashing rapidly
The menu item will be in small letters with a
question mark (?).
In order to navigate in the menu system, one has to answer to the questions in the main and sub
menus. For example, if the question is “WIRELESS DEVICE CONTROL?” is displayed, then press tor
xdepending on the answer.
Pressing twill enter a sub-menu called “Control Inputs?” in this example. Pressing twill enter
the programmable options of this submenu. Pressing xwill exit the individual option, move up
from one sub-menu to the next sub-menu or back to the main menu.

Page: 6
4.2 Entering The Engineer Menu (Default Engineer Code = 9999)
Access to the Engineer Menu maybe denied if:
1) One or more areas are currently armed.
2) The Master User has disabled the function “Allow Engineer Menu” in the Master Manager Menu. If
this is the case ‘Authorisation required’ will be shown on the display.
When in Engineer Menu, the fault (=) LED will flash and high pitch tone will be generated regularly.
4.3 Exiting The Engineer Menu
On completion of programming, the system can be returned back to disarmed mode by either
scrolling to the ‘Exit Engineer Menu’ option or press afrom any main menu option (represented in
capital letters).
4.4 Accessing the Engineers Menu on any external wired keypad
It is possible to access the Engineer Menu on any keypad that is part of the system. Whichever
keypad that is being used, all other keypads will display ‘System Busy’. To access the Engineer menu
on one of these keypads press b.
4.5 Saving The Programming
Any programming done in the engineer or user mode will not be saved on the system until the
Engineer or User menu have been exited.
5. Engineer Menu
Please refer to the Engineer Programming Quick Guide for this chapter. The meaning of every option
presented in the quick programming guide is explained here in detail.
5.1 Date and Time?
All log entries and the system display include the date and time so it is vital that the correct date and
time is programmed. This may be also programmed in the Master Manager Mode.
NOTE: Please note that powering down the system and removing the battery will reset the time and
date information.
5.1.1 Change Year
For the year 2011, enter 11.
5.1.2 Change Month
For March, enter 03.
5.1.3 Change Day
For 31st, enter 31.
5.1.4 Change Hours
Use 24 hour clock format. For 8pm enter 20:00.
5.1.5 Change Minutes
For 7:30, enter 30.
5.1.6 Summer Time Adjust
If activated this option will automatically change 1 hour ahead and backward for the summer and
winter time.

Page: 7
5.2 Learn Wireless Devices?
This function learns or deletes all wireless inputs and bells to the Enforcer 32-WE.
NOTE: The keyfobs are learned and programmed from the Master Manager menu.
5.2.1 Learn Inputs?
Learn Devices?
This menu starts the procedure of learning wireless inputs onto the Enforcer 32-WE.
Input
This menu chooses which input on the system is to be learned. ‘Learnt’ will be displayed if a device
is already learnt, or ‘Available’ will be displayed if it is not.
Input Learning…
1) Open the wireless device.
2) Remove the plastic insulation to enable the battery.
3) If a Device is not learned = The GREEN and RED LEDs on the Device will flash (alternating).
4) Press and hold the ‘LEARN’ button on the Device = The 3 LEDs start cycling around.
5) Release the ‘LEARN’ button = ‘Input Learnt’ will be displayed and a confirmation tone will be
emitted on the panel.
6) If an input has already been learnt, ‘Input learnt already’ will be displayed.
Example: The image below shows how to learn an MC detector. Please note all other wireless
peripherals are learned the same way.
5.2.2 Delete Devices
Already learnt inputs may be deleted from this menu.
Delete All Enter Code
To delete all wireless input devices enter ‘2000’ (this is the Enforcer Security Code). “Please wait”
will be displayed while the Enforcer 32-WE deletes ALL the learnt wireless inputs.
Choose Input to Delete
This option deletes only a specific wireless device learnt to an input. Any inputs that display ‘learnt’
can be deleted. “Please wait” will be displayed while the Enforcer 32-WE deletes the wireless
device. Return to this process to delete more devices.
5.2.3 Learn Bells?
Learn Devices?
Entering this menu allows the learning of wireless bells onto the system.
Select Bell
Selects the bell on the system that is to be learnt. ‘Learnt’ will be displayed if a bell is already
learnt, or ‘Available’ will be displayed if not.
LEARN
>5s

Page: 8
Select BellLearning…
1) Open the wireless bell.
2) Plug the battery connector into the battery terminal.
3) If a device is not learned = The GREEN and RED LEDs on the Device will flash (alternating).
4) Press and hold the ‘LEARN' button on the Device = The 3 LEDs start cycling around.
5) Release the ‘LEARN’ button = ‘Bell Learnt’ will be displayed and confirmation tone on the panel
will be emitted.
If a bell has already been learnt, ‘Bell learnt already’ will be displayed.
5.2.4 Delete Devices
Already learnt bells may be deleted by entering this menu.
Delete All Enter Code
To delete all wireless bells enter ‘2000’ (this is the Enforcer Security Code). “Please wait” will be
displayed while the Enforcer 32-WE deletes them.
Choose Bell to Delete
This option deletes only a specific wireless bell that is learnt. Any bells that display ‘learnt’ can be
deleted. “Please wait” will be displayed while the Enforcer 32-WE deletes the wireless bell. Return
to this process to delete more devices.
5.2.5 Learn Keyfobs Procedure
The keyfobs are learnt and deleted from the Master Manager menu.
Learn Keyfobs?
1) Enter Master Manager Menu (Default Master Code = 1234).
2) Scroll to the function 'LEARN USER CODES KEYFOBS & TAGS'.
3) Choose a user number to allocate the keyfob to.
4) If a keyfob, code or tag are not learnt the space, between the brackets will be empty.
5) If a keyfob, code or tag are learnt, the brackets will show [******].
6) Press and hold any of the keyfob buttons for 5sec.
7) A confirmation tone will be emitted and keyfob will be shown on the display.
Proceed with the programming of actions to each key.
5.2.6 Delete Keyfobs
1) Enter Master Manager Menu (Default Master Code = 1234).
2) Scroll to the function 'LEARN USER CODES KEYFOBS & TAGS'.
3) Choose the keyfob to delete = Between the brackets will be show [******].
4) Press c= The brackets will be showing [ ] to confirm the deletion.
5.2.7 Program Keyfobs
This Menu is used to program the functionality of the buttons on the keyfobs and is available on
the EN defaulted panels in the Engineer Menu, otherwise it can be accessed from the Master
Manager menu after learning the keyfob.
LEARN
>5s

Page: 9
No Input Types Operation
0 Unused Factory default. Input is disabled.
1 Fire Active at all times. Audible Response: Differentiated Internal sound. Pulsed external
sound. Communicator: ‘Fire’ signal
2 Gas Active at all times. Audible Response: Full external + Internal sound.
Communicator: ‘Gas’ signal
3 PA
#
Active at all times. Audible Response: Differentiated Internal sound. Full external
sound. Communicator: ‘Personal Attack’ and ‘Input PA’ signals
4 Silent PA
#
Active at all times. Audible Response: None
Communicator: ‘Personal Attack’ and ‘Input PA’ signals
5 Tamper When disarmed: Audible Response: Internal only. Communicator: ‘Tamper’ signal.
When armed: Audible Response: Full external + Internal sound. Communicator:
‘Tamper’ signal.
6 Instant Active when armed: Audible Response: Full external + Internal sound.
Communicator: ‘Burglary’ signal
7 Entry Delay1
#$
Active when armed: Initiates 'Entry Timer 1' when door open. If system not disarmed
before entry time expires then: Audible Response: Full External + Internal sound.
Communicator: ‘Burglary’ signal. NOTE: See type 43 for Entry Delay2
8 Follow
$
Active when armed, except during entry time. (Acts as an instant input if an Entry
Delay input hasn’t been activated beforehand).
Audible Response: Full external + Internal sound.
Communicator: ‘Burglary’ signal.
11 Push To Arm Active during exit time, to complete arming procedure. No audible or communicator
response. Panel will communicate a final armed event once the Push to Arm button has
been pressed.
NOTE: May be used to act as ‘doorbell’ by use of ‘chime’ input attribute.
Example: Wire the Door Bell button to the input. Enable “Push to Arm” option from
“EXIT MODES”, add a “Push to Arm” input type to the input and enable the “Chime”
attribute for it.
Enter user code, the panel starts arming. Exit the building and close the door. Press the
Bell button. The system will arm. If pressing the Bell button while the panel is in any
other condition the Chime will sound.
12 Switcher Active at all times in armed and disarmed modes. No audible or communication
alarms will be created. When activated it can trigger the associated output for switching
external equipment. If the “Special Log” attribute is enabled for this input an SMS
message will be sent each time the input is activated.
Example: This kind of input type can be used to control CCTV. The concept is that when
a switcher input type is activated, there is an output associated with it following that
input (the most used solution is the use of output type – 0035). The switcher input is
connected to a detector located next to a CCTV camera and the output is connected to
video recording / transmitting equipment. If the detector is activated in armed or
disarmed mode then the recording or transmission will start.
13 24 Hour When armed: Audible Response: Full External + Internal sound;
Communicator: ‘24hr Alarm’ signal.
When disarmed: Audible Response: Full External + Internal sound;
Communicator: ‘24hr Alarm’ signal if enabled in “Alarm Responses” menu.
16 Fault Active when armed or disarmed: Audible Response: internal sounder.
Communicator: Fault event.
If armed only: Activates ‘Global Fault 1’ output type.
If disarmed or armed: Activates ‘Global Fault 2’ output type.
Note that the ‘Technical Fault’ output type is triggered every time a fault is active
including when the fault input type is active.
17 Arming Control Active during arming procedure: No audible or communicator response.
Prevents system being armed whilst the input is in an active state.
18 Shunt Active at all times: No audible or communicator response.

Page: 10
It is possible to associate inputs to the shunt input. It is normally connected to a key-
switch (or equivalent) and when On or Off it shunts or un-shunts the inputs assigned to
it. Associated outputs are available to follow this input type.
Creating a Shunt Group: A shunt group may consist of any number of inputs
programmed as Instant, Tamper, 24hr and Follow types. These must all be allocated in
the same area.
NOTE: These inputs will need to be programmed before allocated to the shunt input.
The inputs in the shunt group/list will only activate after 10 seconds of the nominated
shunt input.
Example: If input 1 is programmed as ‘Shunt Input’, and inputs 2 and 3 are
programmed as “24hr”, then once input 1 has been opened, after 10 seconds inputs 2
and 3 become active.
Action 1: Shunt Input closed
Status: Inputs within the shunt list are shunted ( Disarmed)
Outputs: ‘Follow Input’ PGM output On
Action 2: Shunt Input opened
Status: After 10 seconds inputs in the shunt list are going to activate, i.e. become Un-
shunted (Armed)
Outputs: ‘Follow Input’ PGM output OFF. The ‘Shunt Fault’ PGM output is on for 10
seconds.
Action 3: Shunt Input opened with active detector from the shunt list
Status: After 10 seconds inputs in the shunt list are going to activate, ie become Un-
shunted (Armed)
Outputs: ‘Follow Input’ PGM output OFF. The ‘Shunt Fault’ (type 36) PGM output pulses
until the detector closes.
19 Disarm Only* Active when armed: Accepts input from keyswitch (or equivalent) to disarm the area(s)
assigned to it.
20 Keyswitch
Latched*
Accepts input from keyswitch (or equivalent) to arm/disarm the area assigned to it.
Arming includes normal exit time, etc. Requires latching switch action. Normal operation
is open circuit to arm the system, and close circuit to disarm the system.
21 Entry Shock Active when system armed: This input type is advised to be used in conjunction with
an Entry Delay input. The Entry Delay input is a door contact on the initial entry door,
and the Entry Shock input is a non-latching shock sensor fitted to the door frame in the
vicinity of the lock. If the door is forced a Burglary alarm will be generated immediately
instead.
22 Line Fault Active when fail. This input type is used to detect external transmission equipment line
fail (output). If activated it will give a line fault alarm, and will signal telecom line fault on
expiry of line fault timer. It can be used in conjunction with CCTV input (type 39)
23 Keyswitch
Pulsed*
Accepts input from keyswitch to arm/disarm the area(s) assigned to it. Requires
momentary action switch to toggle arm/disarm state.
Note that Grade 1 operation only allows arming from the push button, but requires
means to abort arming (not to disarm)
29 Interior This will work the same as an instant type input, the only difference is that when CID
reporting is programmed then any inputs that are programmed as Interior will report CID
event 132.
32 Flood This input type will work as a 24hr input, any inputs that are programmed for Flood will
activate the external siren and will report CID event 113.
39 CCTV Active at all times: No audible alarm or communicator response.
The CCTV input should be connected to an external detector located next to a CCTV
camera. An output can be programmed to follow this input and the output should be
connected to a CCTV recording, transmission or other device. An input programmed as
“Line Fault” (input type 22) should also be connected to an output of the CCTV
transmission Device. If the CCTV transmission line has been cut or missing the ‘Line
Fault’ input will activate. Following this, at each activation of the CCTV input the panel
will signal CID events for ‘Silent Burglary’ and Line Fault. No audible alarm will be

Page: 11
Choose User
Select the user keyfob to program.
Chose User Select Button
The different buttons and button combinations that may be programmed are:
[1] Lock Button
[2] Unlock Button
[3] Button I
[4] Button II
[5] Lock + Unlock Buttons
[6] I + II Buttons
[7] Lock + I Buttons
[8] Unlock + II Buttons
Choose User Select Button Button Action
Options are ‘show status’, ‘arm area’, ‘disarm area’ and ‘operate output’. Two key combinations
may also have ‘panic attack’ assigned to them. ‘Arm Area’ features a sub option to choose which
area to arm. ‘Operate Output’ features a sub option to choose which output to trigger.
Choose User Select Button Button Action User Controls
If an action is programmed as ‘Arm Area’ then the areas which the keyfob will control can be
selected here.
PLEASE NOTE: ONCE ALL WIRELESS INPUTS (DETECTORS AND DOOR CONTACTS) ARE
LEARNT, INPUT TYPE MUST BE ASSIGNED TO THEM, THIS IS PROGRAMMED IN
‘PROGRAM INPUTS’.
5.3 Program Inputs?
By default, all inputs are set to ‘unused’. Before programming, identify input type required:
#These inputs cannot be bypassed.
*Use of inputs 19, 20 and 23 will make the system unable to comply with EN50131-1 Security
Grade 2.
$ Ensure that these inputs are used on an entry/exit route
5.3.1 Choose Input
Choose an input to program.
Input In Area
Enter the areas for input to operate in.
Common Input
In certain situations, a ‘common’ area may be needed. A common area is an area that only arms if
other specific areas are armed.
Example: A reception in a building will only need to be armed if the offices and warehouse are
armed. If the office is armed, but the warehouse isn’t, then the reception would still need to be
inactive so people would be able to leave the premises. One input can be allocated to one or more
areas. In this example the inputs located in the reception area will be in the offices and warehouse
areas and have the common attribute activated.
Area A: Office - Inputs 1, 2, 3, 4 and 8.
Area B: Warehouse - Inputs 5, 6, 7 and 8.
Input 8: The detector connected to this input is going to be the input located in the Reception and
created. If the Line Fault is not active it will just log the activations of the CCTV input into
the event log.
40 Perimeter This will work the same as an instant type input, the only difference is that when Contact
ID reporting is programmed, then any inputs that are programmed as Perimeter will
report Contact ID event 131.
41 Patrol / Keybox This input type will work similarly to a switcher input, it does not trigger an alarm but will
report Contact ID event 250 and is also a useful input type when an output is required to
follow the ‘Keybox’ type input.
42 Medical This is a 24 Hrs type input it will activate the external sounder and report a Contact ID
event 100.
43 Entry Delay 2
$
Any input programmed as Entry Delay 2 will act as input type 07, but the associated
entry timer will use Entry Timer 2, rather than Entry Timer 1.

Page: 12
is common to Area A and Area B.
Input 8 will only be active if the Area A and Area B are both armed. If one of them is disarmed the
input 8 will not be active either.
5.3.2 Input Attributes?
No Attribute Operation for both wired and wireless inputs
1 Chime When enabled the system loudspeaker(s) will ‘chime’ when an input is triggered
whilst the alarm panel is disarmed. Chime can be single – sounding once of follow –
sounding while the door is left open. NOTE: The chime can be turned On or Off in
disarmed mode by pressing [c] when all Entry Delay inputs are closed.
2 Allow
Bypass*
Enables the input to be manually bypassed during the arming procedure or from the
user menu whilst the panel is disarmed.
3 Double
Knock
If enabled, an alarm will be generated if this input is triggered twice within the pre-
programmed time window or if the input remains active for that period. The double
knock option does not work on ‘Follow’ input type.
4 Combined
Input
Alarm will only be generated if 2 inputs one next to the other with Combined Input
attribute have been activated at the same time. This option is very useful for setting
up out door perimeter protection.
5 Normally
Open
#
Both wired and wireless inputs are normally set to Normally Closed. This attribute
allows to set up the input as a Normally Open.
6 Mask Test The panel will not arm if the user does not activate each detector with this attribute
after starting the arming timer. This is a way to prevent arming the system with
masked or faulty detectors.
7 Non Activity
Input
This attribute works in conjunction with the NAT (Non Activity) timer. If a detector
has not been activated during the NAT time the NAT output if programmed will be
activated. An event will be registered in the log too.
8 Special Log
(SP)
Forces a log entry when the input is opened or closed, even when an alarm does not
result. May be selected to apply when a system is armed, when disarmed, or
always.
*Only the bypassing during the arming procedure is EN50131-1 approved
#The use of this input attribute will make the system unable to comply to EN50131-1 Security Grade
2
5.3.3 Input Description?
2 text labels can be associated to each input:
Enter Number: This is commonly used to write the Input Number here: Input 1, Input 2 etc. This
label will show the event log, following alarms, reported in the SMS alarms as a reference point.
There are only 7 characters available for this label.
Enter Name: This is commonly used to write the location of the input. There are 14 characters
available for this label. Example: Input Number = Input 1; Input Name = Living Room. In case
there has been a tamper alarm on the input -on the SMS will be shown: ‘Input 2, Living Room,
Tamper Alarm’. On the display will be shown: 2-Living Room, Tamper on Input. Meaning: Tamper
alarm on input 2 that is the Living Room.
5.3.4 Manually Bypassing Inputs Procedure
Method 1: Whilst the system is arming, press the tkey to bypass inputs.
Method 2: Enter user menu and from the “Bypass Inputs” option bypass the inputs required.
NOTE: Only Method 1 is EN50131-1 Grade 2 compatible. The input attribute “Allow Bypass” must
be enabled on each input that the user has the ability to bypass.
5.3.5 Automatic Bypassing Inputs Procedure
Inputs may be automatically bypassed when the panel auto re-arms if this option is enabled in the
system options.

Page: 13
5.4 Install RIXs?
Up to 4 x RIX8i or RIX8+ may be installed on the system. Any Remote Input Expanders (RIXs)
installed on the Enforcer 32-WE system must be enabled in the ‘Install RIXs’ menu. For installation
details, please refer to the Installation Reference manual.
5.4.1 RIX Address
Select the address of the RIX to enable (Address 0-3).
5.4.2 RIX Installed
Enable/Disable the RIX installed. 1 = Enabled / 0 = Disabled
5.4.3 RIX Location
The location text is stored for reference on later maintenance visits i.e. “GROUND FLOOR”. For
information on how to use predictive text, please see page 5.
NOTE: We recommend if adding wired input expander RIX’s -to use the version with the PSU
integrated on board, because the Enforcer PSU might be insufficient to power multiple additional
detectors.
5.5 Program Outputs?
This option enables the programming of the outputs on the Enforcer 32-WE and any devices that are
connected.
5.5.1 Endstation PGMs?
These are the outputs on control panel itself. There are 3 outputs on the I/O module of Enforcer –
BELL PGM, STB PGM and PGM. All of them are programmable but the BELL and STB are allocated
to follow the alarm in any area as bell and strobe.
5.5.2 RIX Module PGMs?
These are the outputs that are located in the RIX8+ input expander module, if used. There are 4
PGMs located on this module.
5.5.3 ROX Module PGMs?
This option enables the addition of a wired ROX module to Enforcer as well as programming of the
PGM options for the outputs in the module.
5.5.4 Keypad PGMs?
Allows the programming of the PGM options for the outputs located on the wired keypads.
5.5.5 Reader PGMs?
Allows the programming of the PGM options for the outputs located on the wired readers.
5.5.6 User Outputs?
These outputs are used for creating automation control for Devices. The user can control them
remotely from the user menu on the keypad. The automated user outputs can be programmed
either latched or pulsed.
Polarity of the PGMs: The polarity of the outputs is normally switched negative i.e. in normal status
OFF = 0v and in active status ON = 12v.
NOTE: The PGM Outputs polarity cannot be inverted.
No. Output Type Active Restore
0000 Not Used
0001 Fire At fire alarm activation When a valid code is entered
0002 PA Any At personal attack activation When a valid code is entered
0003 Burglary Any At burglary alarm from any area At first valid code entry
0004 Final Arm All When ALL areas are armed At code entry to disarm
0005 Open After Alarm
(Abort)
When system is silenced after ‘burglary’
alarm has been activated
After 2 minutes
0007 Tamper Any Tamper alarm in any area At code entry to silence
0008 Duress Any At a Duress alarm in any area When a valid code is entered
0009 PA Device Any At alarm on a PA input only from any
area. (This does not include the keypad
PA)
When a valid code is entered
0010 Gas At gas alarm When a valid code is entered

Page: 14
0011 Arm Fail Pre-set time after start of exit time, if exit
procedure is not complete
At code entry to rearm
0012 Entry Deviation When deviation from entry route occurs,
during entry time
At code entry to disarm
0013 System Ready Any When any of the inputs but the Entry
Delay and Follow are closed
If fault exists, and after final arm
0014 Bell Any After alarm in any area When alarm silenced or when siren
timer expires
0016 Strobe Any After alarm in any area When disarmed or when strobe
timer expires
0017 Bypass Rearm Any When inputs are bypassed at rearm in any
area
When system disarmed
0018 Burglary
(Unconfirmed) Any
At Burglary alarm in any area At code entry to silence
0019 Ready All When all inputs but the ‘Entry Delay’ and
‘Follow’ inputs are closed
If fault exists, and after final arm
0020 Exit Starts All At start of exit time to arm LAST area At disarm FIRST area (i.e. no longer
fully armed)
0021 Exit Starts Any When exit time starts to arm FIRST area At code entry to disarm LAST area
0022 Final Arm Any When ANY area has been armed At code entry to disarm LAST area
0023 Strobe if Arm Fail Works similar to output 016, but also fires if the ‘arm fail’ timer expires.
0024 Unable to Arm This output turns on for 5 seconds when the system is disarmed via a keyswitch
input (either pulsed or latched keyswitch)*
0025 Keyswitch Disarm Output activates when an arming procedure is completed with inputs bypassed.
0026 Arm with Bypass Active when the system is armed with an input bypassed.
0027 Pulsed Burglary
Any
Active when burglary alarm is triggered, but deactivates once the Pulsed
Intruder timer has expired (see Program Timers).
0028 Power Fault Active during low volts and battery faults. Restores at code entry after fault
cleared.
0031 Entry Active during any Entry time
0032 Exit Active during any Exit time
0033 Entry / Exit Active during any entry or exit time
0034 Lights When exit or entry timer starts 20 seconds after arm/disarm
procedure completed
0035 Follow Input Active when a specific input number has been activated. It allows the following
options to be programmed:
-Follow Type (Follow, Timed, Latched, Code Reset);
-Follow What (Input, Shunt List, Sub-Area, Area);
-Follow When (Always, When Armed, When Disarmed);
-Input to Follow (between 1 to 64)
0036 Shunt Fault This input activates if someone tries to shunt an input group where some of the
inputs allocated to this group are open.
0037 Restore 1 At code entry to arm. The normal state of
this input is 0v and it changes to 12v
when activated.
After 3 seconds
0038 Restore 2 Activates whenever an additional area is
armed. The normal state of this input is
0v and it changes to 12v when activated.
When disarmed
0039 PIR Latch 1 When armed (and in Walk Test) At alarm, or when disarmed
0040 PIR Latch 2 This is the inverse polarity to
PIR Latch 1
At alarm, or when disarmed
0041 AC Mains Good Output showing the 230v mains supply is present

Page: 15
0042 PIR LED Enable This output activates during walk test
0043 Follow Test Output will activate only when tested from the Engineer menu ‘Test Outputs’ in
the ‘Engineer Tests’. This output can be used as additional facility for testing the
operation of a Bell. An output programmed to one of these configurations (43 &
44) may be used to trigger a relay to break the hold-off connection to the Bell –
or even to provide the hold-off directly.
0044 Off During Test Output is normally active and will deactivate only when tested from the Engineer
menu ‘Test Outputs’ in the ‘Engineer Tests’.
Same as 43 but opposite activation.
0048 Walk Test This output is active during walk test, and will only deactivate when all detectors
have been tested
0049 Detector Masked If any detector goes into ‘mask’ condition
the output will activate
When masking fault clears
0050 Follow 24 Hour If any input programmed as ’24 Hour’
activates
When input is restored
0051 Line/GPRS Fault When Telephone or GPRS Line Fault is
present.
When fault clears
0052 AC Mains Fail After pre-set time without mains power On restoration of mains
0053 Battery Fault When battery disconnected or load fail
detected
At next valid code entry
0054 Low Volts When less than 11.2v are present When fault clears
0055 Global Fault 1
(Grade 2)
Activates if any fault occurs only when
system is armed
When all faults cleared
0056 Global Fault 2
(Grade 3)
Activates if any fault occurs at any time When all faults cleared
0057 German Relay For future development. Do Not Use.
0058 Guard Code Used When ‘guard’ code used on the system After 60 seconds
0059 Engineer Access When entering Engineer Mode When leaving Engineer Mode
0060 Follow Power Up At power up Live for 45 seconds
0063 Test UK STU Activates when a test call is sent When test completed
0064 Pre RM Service Activates 1h before the RM Service call When test completed
0065 Input Fault
(Follow NAT)
Activates when there is no activity on an
input in the end of the “NAT-Non Activity
Timers” in Change Timers.
When there is activity.
0066 ATE Pin Not Used Makes the ATE pin 5V or 0V depending on whether ATE outputs are inverted
0067 Follow Chime Active while a Chime signal is created on the panel
0170
--
0199
User Defined 01-30 The user outputs are used for user automation to control external Devices. They
can be controlled via the keypad from the user menu and can be programmed as
‘latched’ or timed (1 to 99 sec).
0202 PA A (As 0002 for Area A ) 0213 System Ready A (As 0013 for Area A )
0203 Burglary A (As 0003 for Area A ) 0214 Bell A (As 0014 for Area A)
0204 Final Arm A (As 0004 for Area A ) 0216 Strobe A (As 0016 for Area A )
0207 Tamper A (As 0007 for Area A ) 0217 Bypass At Rearm A (As 0017 for Area A )
0208 Duress A (As 0008 for Area A ) 0218 Burglary (Unconfirmed) A (As 0018 for Area A )
0209 PA Device A (As 0009 for Area A ) 0219 Ready A (As 0019 for Area A )
0210 Fire Reset A (As 0010 for Area A ) 0220 Exit Starts A (As 0020 for Area A )
0620-0639 Logic Gate 1-20. Logic gate outputs (programmable via the upload/download software)
Then this pattern repeats for all other areas other areas so that:
0222-0240 Area B 0242-0260 Area C 0262-0280 Area D
1001-1066 Active when input opened and close when input is closed
*The use of pulsed or latched keyswitch will make the system unable to comply with EN50131-1

Page: 16
5.6 Install Keypads and Readers?
Ensure that all keypads and readers are addressed correctly (at the device) before enabling and
addressing them in this function. To address at the device please refer to the installation reference
manual.
NOTE: At least one keypad/reader should have the ability to disarm any areas programmed.
5.6.1 Device Address
Address [0] is reserved for the Enforcer built in LCD keypad only. In the addresses from [1] to [3]
is possible to allocate external wired readers or LCD keypads.
5.6.2 Device Type
The device types that is possible to program are LCD keypads [0] or Readers [1].
Reader Device Type
If a Reader is enabled, it can operate as the following:
Arm/Disarm
This will make the Reader act like a normal keypad (arming/disarming the areas etc.)
Device Arms Areas: This feature programs which area(s) the reader can arm.
Device Disarms: This feature programs which area(s) the reader can disarm.
Device in Area: This feature programs in which area(s) the reader is active.
Door Name: Enter the name of the door such as Front Door.
Door Location: Enter the location of the door such as First Floor.
Arm/Disarm Sub-Area
A reader can be used to create sub-areas controlled independently from the area.
Add Inputs: Each sub-area may consist of any number of inputs, all of which must be allocated to
the same area. No input may be allocated to more than one sub-area. Entry Delay input types
cannot be allocated to a sub-area and in the sub-area the arming/disarming of the inputs is
immediate without delay timers.
The sub-areas can be operated by proximity tag, or by key (or other) switch wired into the first
input on the tag reader. Notice that the proximity Tags for sub-area control are programmed
through the Manager menu using the ‘change codes’ options. The reader provides ‘Alarm’ and
‘Ready’ outputs dedicated to that sub-area. It also provides relevant indications, including
Arm/Disarm status, so should always be located adjacent to the controlling Key switch where this
is used.
Sub-Area Arms: If this option is selected as ‘If Area Armed’ then the sub-area will always arm
when the area in which is it located is armed. If selected as ‘Never’ it will always require manual
arming from the tag. The sub-area must ALWAYS be disarmed manually.
An additional option is available in the ‘SYSTEM OPTIONS’ menu, to permit an ‘Open After Alarm’
(abort) signal to be generated by silencing an alarm at the Reader after an alarm has been
generated in the sub-area. Please see page 21.
Action Status Notes
Disarmed Detectors within sub-areas are
inactive
‘Disarmed’ indication lit
Sub-areas input triggered No response
Attempt to arm sub-areas with
an open input
- ‘Fault’ LED flashes and intermittent
tone to indicate ‘cannot arm’
Arming with no open inputs Sub-area arms ‘Disarmed’ LED goes out
Sub-area input triggered Alarm generated ‘Alarm’ LED lights, alarm tone
generated
Valid code entered at a Keypad
whilst alarm in sub-area is active
Alarm silenced by user code Sub-area remains armed
Sub-Area Control: The sub area can be controlled by Tag or Input. When an input is used to control
the sub-area a keyswitch input type should be used and connected to an external key or switch.
Sub-Area Name: Enter the name of the sub-area such as ‘Private Office’.
Sub-Area Location: Enter the location of the sub-area such as ‘First Floor’.
Assigning Tags to Sub Area Reader: To assign tags to the sub-areas, enter the master manager
menu and select ‘Change Codes’, add a new user code (tag) and when the prompt shows ‘Sub Area
Access’, enter the address of the reader you would like the tag to operate for the sub-areas.

Page: 17
Access Control
Allows the reader to control doors fitted with electrical locks. On the readers there are 2 inputs that
also can be outputs. They can be connected to the lock for opening and controlling the door.
Lock Open Time: This is the time the door release is going to be active when a valid tag is
presented.
Door Open Time: This is the time the door is allowed to be open before triggering an alarm.
Door Name: Enter the name of the door such as Front Door.
Door Location: Enter the location of the door such as First Floor.
NOTE: Access control falls outside the scope of EN50131-1.
Disarm Only
Allows the reader to be used to disarm the system only.
Device Disarms: This feature programs which area(s) the reader can disarm.
Device in Area: This feature programs in which area(s) the reader is active.
Device Name: Enter the name of the door such as Front Door.
Device Location: Enter the location of the door such as First Floor.
Entry Control
Allows the reader to be used as arm/disarm Device and access control.
Device Arms Areas: This feature programs which area(s) the reader can arm.
Device Disarms: This feature programs which area(s) the reader can disarm.
Device in Area: This feature programs in which area(s) the reader is active.
Lock Open Time: This is the time the door release is going to be active when a valid tag is
presented.
Door Open Time: This is the time the door is allowed to be open before triggering an alarm.
Door Name: Enter the name of the door such as Front Door.
Door Location: Enter the location of the door such as First Floor.
Keypad Device Type
Device Arms Areas: This feature programs which area(s) the keypad can arm.
Device Disarms: This feature programs which area(s) the keypad can disarm.
Device in Area: This feature programs in which area(s) the keypad is active.
Door Name: Enter the name of the door such as Front Door.
Door Location: Enter the location of the door such as First Floor.
5.7 Program Timers?
Timers Description Options
Entry Time 1
Entry Time 2
Programmes the entry time for each area. If entry time is started at a door
programmed in multiple areas, the longest time will apply. Entry time 1
will apply to any inputs programmed as “Entry Delay 1” type, and Entry
Time 2 will apply to any inputs programmed as “Entry Delay 2” type.
Ensure that timer is no longer than 45 seconds in order to comply with
EN50131-1.
0-255 seconds
Exit Time Programmes the exit time for each area. If the system is being armed at
an arm device programmed as ‘IN’ multiple areas, the longest of those
times will apply.
0-255 seconds
Bell Time Cut off time for external sounder. Separate for each area. Repeat above
steps for each of the Enforcer 32-WE areas programmed.
0-15 minutes
Bell Delay Delay after burglary alarm before bell activation.
NOT valid within 3 minutes of final arm, or after entry time started. If
‘Silent 1st Alarm’ selected in alarm responses, delay commences at
confirmed alarm.
0-20 minutes
Strobe Time The duration of time the strobe output remains live after the bell time
ends, ‘99’ means endless.
0-99 minutes
Number Re
arms
Number of times system re-arms after bell time ends. Re-arm number
applies to each area, and does not affect emergency alarms. ‘9’ = ‘always
re-arm’.
0-9
AC Fail Delay Time delay before mains failure or technical alarm signalled. ‘250’ = never
alarms. System change-over to battery supply and associated ‘alert’
indication is always immediate. Mains Fail message on keypad not
permitted until valid code entry.
0-250 minutes

Page: 18
Final Door
Delay
Time between final door input closing and system arming.
When a code is entered to arm the system the exit time will start but the
system will not arm until it sees the final exit door open and close and
duration of the final door delay.
0-255 seconds
Double Knock Length of filter period applied to inputs with ‘Double Knock’ input attribute. 0-75 seconds
Delay Send
Entry
Delays ‘Burglary’ alarm signalling if an alarm is generated by deviation
from the entry route. Delay Send Entry must be programmed for a
minimum of 30 seconds to comply with EN50131-1.
0-255 seconds
Line Fault
Delay
Duration of Telecom (GPRS) Line Fault before ‘Line Fault’ alarm triggered,
‘250’ endless.
0-250 seconds
Arm Fail Time If a system has not been armed within the entry delay time, for example if
a door was left open -the ‘Arm Fail Time’ will take over and at the expiry of
this time an alarm will be created. This time should be longer than the
Entry Delay Time.
0-255 seconds
Guard Code
Delay
The minimum time an alarm must have been present before a ‘Guard’ code
will be accepted to disarm.
0-10 minutes
Fire Bell Time Cut off time for fire alarm. ‘99’ = endless. 1-99 minutes
Arm Fail
Warning
The ‘Arm Fail Warning’ will overwrite the ‘Arm Fail Time’ feature if the
‘Alarm When Arm Fail’ in System Options has to be set as ‘NO’.
Example of how this feature works: Set ‘Arm Fail Warning’ to a longer time
than the ‘Entry Delay Time’. For example if the ‘Entry Delay Time’ is set to
30sec the ‘Arm Fail Time’ could be set to 1 minute. If the system is not
armed after 30sec then the Entry Delay Tones will start and the system will
be disarmed at the end of the Arm Fail Warning time. An event called ‘Arm
Fail Warning Activated’ will be logged in the event log too.
0-99 minutes
NAT Day
Timer
NAT stands for ‘Non-Activity Timer’. This is used in conjunction with the
input attribute ‘Non Activity Input’, and will monitor the chosen input for
the selected number of days. At the expiration of the timer, and if the
input has not opened within that time, then this will be stored in the panel
log as ‘Non Activity fault’ and there will be an output activated if
programmed to it. Send SMS message if “Special Log” is on.
0-14 days
NAT Hours
Timer
NAT stands for Non-Activity Timer. This is used in conjunction with the
input attribute ‘Non Activity Input’, and will monitor the chosen input for
the selected number of hours. At expiration of timer, and if the input has
not opened within that time, then this will be stored in the panel log as
Non Activity fault and there will be an output activated if programmed to
it. -Sends SMS message if “Special Log” is on.
00-23 hours
Pulsed Burglar
Any
This option sets up the duration of the pulse of an output programmed as
“Pulsed Burglary Any” which activates after a burglary alarm.
0-255 seconds
WLs
Supervision
Time
This is the time window before a supervision fault will be signalled. For
example: if the time is set for 2 hours, then any device that doesn’t
communicate with the Enforcer 32-WE within that period will cause a
supervision fault. It must be programmed to 2 hours or less for compliance
with EN 50131.
0-99 hours
WLs Jamming
Time
This is the time window that if a wireless device had its signal ‘blocked’ a
fault would display. For example, if the time is set for 30 seconds, then if a
wireless device is ‘jammed’ for longer than 30 seconds a fault will be
displayed.
Must be set to 30 seconds or less (but not zero) for compliance with EN
50131.
0-100 seconds
Service Time This is a timer that can be programmed in days, and will display a
message to the user warning that a service is due. An engineer code will
clear the message.
367

Page: 19
5.8 Change Codes?
All codes may be 4, 5, or 6 digits long and can also be assigned as proximity tags and keyfobs. 75
user codes are available
NOTES: Only ‘Duress/Guard’, ‘Master Manager’ and ‘Engineer codes’ can be changed by the engineer.
User codes can only be changed by the Master Manager from the Master Manager menu. The Master
User and Engineer Codes cannot be deleted.
User Arm and Disarm System. Also for Access Control and Sub Area
Control functions
Programmed by Manager
only.
Manager
Default: 1234
Arm and Disarm System. Also access to Manager menu
functions
Programmed by Manager
or Engineer.
Engineer Access to all engineering functions; also arm/disarm system for
test purposes.
Programmed by Engineer.
Duress Disarm system, generating silent ‘Duress’ signal. Programmed by Engineer.
Guard Disarm system, but only after an alarm has been active for a
minimum time (programmable). Also arm system. An output
type is available to activate whenever this code is used.
Programmed by Engineer.
5.8.1 Change Duress/Guard Codes?
Choose Code Number
If a code or tag is already allocated, the display will show [******]. Press to clear the code.
Choose Code Number User Type
The user type can be Duress or Guard.
Duress Code
The Duress code can arm or disarm the system and if used, a Duress communication event will be
sent. An output type is available to activate whenever this code is used (Duress type 008 - see
page 31 Program Outputs).
User In Area
Choose the area the code is active in – A,B,C,and D.
User In AreaUser Arm Options
[0] Disarm/Arm: The code will arm and disarm the areas selected in the previous option.
[1] Disarm Only: The code will only disarm the areas selected in the previous option.
[2] Arm Only: The code will only arm the areas selected in the previous option.
[3] None: No option programmed.
User In AreaUser Arm OptionsArm Area Choice
If a user code is allocated to more than one area and the Arm Area Choice option is set to NO, the
code will automatically arm all areas it has been allocated to when the code is entered to arm. If
the Arm Area Choice has been set to YES then the user will be given the ability to choose which
area to arm when the arming procedure has been activated.
User In AreaUser Arm OptionsArm Area ChoiceUser Name
Write the name of the user for this code.
Guard Code
This code can disarm the system, but only after an alarm has been active for a minimum time
programmable in the timers. Use of this code will generate a normal user arm/disarm event. An
output type is available to signal whenever this code is used.
User In Area
Choose the area the code is active in – A,C,B,and D.
User In AreaUser Arm Options
[0] Disarm/Arm: The code will arm and disarm the areas selected in the previous option.
[1] Disarm Only: The code will only disarm the areas selected in the previous option.
[2] Arm Only: The code will only arm the areas selected in the previous option.
[3] None: No option programmed.

Page: 20
User In AreaUser Arm OptionsArm Area Choice
If a user code is allocated to more than one area and the Arm Area Choice option is set to NO, the
code will automatically arm all areas it has been allocated to when the code is entered to arm. If
the Arm Area Choice has been set to YES then the user will be given the ability to choose which
area to arm when the arming procedure has been activated.
User In AreaUser Arm OptionsArm Area ChoiceUser Name
Write the name of the user for this code.
NOTE: For both duress and guard codes it is possible to program a tag too. In case a tag is
programmed it has to be associated to a reader.
5.8.2 Change Master Manager Code
If a code or tag is already allocated, the display will show [******]. Press the key to clear the
code and use the numeric keys to enter the new code. This option allows the engineer to change
the Master Manager code -should this been lost or forgotten.
User In Area
Choose the area the code is active in: A,B,C,and D.
User In AreaUser Arm Options
[0] Disarm/Arm: The code will arm and disarm the areas selected in the previous option.
[1] Disarm Only: The code will only disarm the areas selected in the previous option.
[2] Arm Only: The code will only arm the areas selected in the previous option.
[3] None: No option programmed.
User In AreaUser Arm OptionsArm Area Choice
If user code is allocated to more than one area and if the ‘Arm Area Choice’ option is set to ‘NO’,
the code will automatically arm all areas it has been allocated to in the same time. If the Arm Area
Choice has been set to YES then the user will be given the ability to choose which area to arm
when the arming procedure has been activated.
User In AreaUser Arm OptionsArm Area ChoiceUser Name
Write the name of the user for this code.
5.8.3 Change Engineer Code
If a code or tag is already allocated, the display will show [******]. Press to clear the code
and use the numeric keys to input the new code.
5.9 Volume Control?
The Volume Control function applies to both the buzzer and the internal sounder.
5.9.1 Area A,B,C,D Entry Tone Volume
0=Completely Silent, 1=Silent, but beeps when the system is armed. 2-5 Buzzer 6&7 = Internal
Siren
5.9.2 Area A,B,C,D Exit Tone Volume
0=Completely Silent, 1=Silent, but beeps when the system is armed. 2-5 Buzzer 6&7 = Internal
Siren
5.9.3 Alarm Volume
0=Completely Silent, 1=Silent, but beeps when the system is armed. 2-5 Buzzer 6&7 = Internal
Siren
5.9.4 Fire Alarm Volume
0=Completely Silent, 1=Silent, but beeps when the system is armed. 2-5 Buzzer 6&7 = Internal
Siren
5.9.5 Technical Alarm Volume
0=Completely Silent, 1=Silent, but beeps when the system is armed. 2-5 Buzzer 6&7 = Internal
Siren
5.9.6 24 Hour Alarm Volume
0=Completely Silent, 1=Silent, but beeps when the system is armed. 2-5 Buzzer 6&7 = Internal
Siren
5.9.7 Chime Volume
0=Completely Silent, 1=Silent, but beeps when the system is armed. 2-5 Buzzer 6&7 = Internal
Siren
5.9.8 Code Stops Sound
This option is very useful when 2 or more independent areas are used on one system. If
programmed as ‘Yes’, once an alarm has been generated in an area, the user of a different area by