Pyronix Enforcer 32WE User manual

Wireless
Setup Guide
EN50131-3 : 2009
EN50131-6 : 2008
EN50131-5-3 : 2005
Security Grade 2
Environmental Class II RINS1348-3

Default codes:
User code:1234
Master Manager Code: 2222
Engineer Code: 1111

3
Contents Page
The Enforcer 4
Wireless Devices 5
Simple Learning Guide 6
Powering Up / Entering & Exiting Engineers 8
Learning Contacts and Detectors 9
Learning Bells 10
Learning Keyfobs 11
Deleting Inputs / Bells 12
Diagnostics 13
Wireless Functions 15
Fault Displays 16
MC1-WE 17
KX12DQ-WE 20
KF4-WE 23
SHOCK-WE 25
DELTABELL-WE 28

4
The Enforcer
D
A
B
C
SPACE 
1
4
7 8
5
23
6
9
0
,/+.
ABC
JKL
MNO
PQRS
TUV
WXYZ
DEF
GHI
BYP
a= Exit manager menu
b= Moves backwards to the previous menu item
c= Enables chime and displays additional information in the log
d= Moves forward in the log, scrolls between options/enters the master
manager menu/bypasses inputs
fp= Not used
[]= Directional buttons.
t= Selects items and enters menus.
x= Cancels items, resets the panel and moves to next item in Master
Manager menu
The Enforcer Control Panel
Wireless Keyfob
The keyfob may be used to set and unset
the Enforcer, as well as other operations.
Please see page 11 for programming.

5
Wireless Devices
D
A
B
C
SPACE 
1
4
7 8
5
23
6
9
0
,/+.
ABC
JKL
MNO
PQRS
TUV
WXYZ
DEF
GHI
BYP
Wireless Detectors
PIR Sensitivity
High
Low
Status LEDs
ALARM
LEARN
LEARN
ALARM
ALARM
 
 


Learn Button
Wireless Contacts
Enable contact 1
Disable contact 1
Status LEDs
Learn Button
Wireless Deltabell
Connections for power supply
Status LEDs
Learn Button
Please note: that if learning smoke/carbon sensors
only a learn button and 1 LED will be present.
LEARN

6
Simple Learning Guide
RADIO DEVICE
CONTROL?
Control Inputs? Learn Devices? Input 01
Available [01] Learning...
Use b and x to scroll to:
Press
t
Press t
Press tEnter Input.
Press t
Learning Inputs (In Engineer’s Mode)
RADIO DEVICE
CONTROL?
Control Inputs?
Control Bells?
Learn Devices?
Input 01
Available [01]
Learning...
Learning Bells (In Engineer’s Mode)
Use b and x to scroll to:
Press
t
Press x
Press t
Press t
Enter Input.
Press t
Enforcer
Time 8:30am c
Enter Your Code
[*****]
SET DATE & TIME?
CHANGE CODES?
Change User
Codes? User Number [02]
Enter user code
[ ]
Learning Keyfobs (In Day mode)
Use b and x to scroll to:
Press
D
Enter Master
Manager Code
Press
x
Press t
Press t
Select User
Press
t

7
Press the ‘LEARN’
button on the detector/
contact until the LEDs
cycle, then release.
Input learnt
successfully
Input Learnt The input types will then
need to be programmed.
Please see ‘Change Inputs’
in the programming manual.
Bell Learnt
Press the ‘LEARN’ button
on the bell until the LEDs
cycle, then release.
Bell learnt successfully
Enter user code
[******]
User Name
_Select Button
Lock [1]
Button Action[2]
Set Area
Press and hold
a keyfob button
until the RED and
GREEN LED flash
fast, then release.
Code learnt
successfully Enter user
name
Press
t
Use []
to select
button.
Press
t
Use [] to
select action
Press
t
Please note: that if learning smoke/carbon sensors
only a learn button and 1 LED will be present.
LEARN
LEARN

8
Powering Up / Entering & Exiting Engineers
Enforcer
Time 03:21c
Please Wait...
SOFTWARE
REVISION?
SOFTWARE
REVISION?
EXIT ENGINEER
MENU?
Enforcer
Time 03:21c
Enforcer
Time 03:21c
Entering the Engineer Menu
Enter the engineer’s code
Any faults are shown. Press
x
Press x
Engineer’s Menu
Active Faults
Battery Fault100
SET/UNSET
SYSTEM?
Enforcer
Time 03:21c
SOFTWARE
REVISION?
Enter Your Code
[**** ]
Use b and x to scroll to:
Press
t
OR
Day Mode
Press
a *
Day Mode
*Note: You can only exit engineer’s mode
if a main menu is showing (capital letters)
Day Mode
Exiting the Engineer Menu
Please note that the initial power up may take a
few minutes.
Once the time is displayed, programming can
begin.

9
Powering Up / Entering & Exiting Engineers
Learning Contacts & Detectors
RADIO DEVICE
CONTROL?
Control Inputs?
Learn Devices?
Learning...
Input 01
Available [01]
Input 02
Learnt [02]
Input Learnt
Input Learnt
Already!
It is recommended that all detectors, door contacts or
smoke detectors are learnt at the Enforcer before any
installation/mounting is done. This makes learning
much quicker.
A maximum of 32 wireless inputs may be learnt.
Even though the ‘learn’ may be successful, the
position of the input in a property must be tested for
signal strength before it is actually ‘xed’ into place.
Please see page 13 when analysing the wireless
range and signal strength.
Before learning each input (detector or door contact)
check that the battery is present and inserted
correctly.
Follow the instructions on the right to start learning
the inputs.
An input that is learnt correctly will ash the GREEN
LED briey and ‘Input Learnt’ will be displayed on
the keypad. Both of these instances need to occur to
indicate a successful learn.
Once learning has completed, each input needs to be
given a type (nal exit, intruder,etc.) please see the
main programming manual (Change Inputs) for more
information.
D
A
B
C
SPACE 
1
4
7 8
5
23
6
9
0
,/+.
ABC
JKL
MNO
PQRS
TUV
WXYZ
DEF
GHI
BYP
D
A
B
C
SPACE 
1
4
7 8
5
23
6
9
0
,/+.
ABC
JKL
MNO
PQRS
TUV
WXYZ
DEF
GHI
BYP
D
A
B
C
SPACE 
1
4
7 8
5
23
6
9
0
,/+.
ABC
JKL
MNO
PQRS
TUV
WXYZ
DEF
GHI
BYP
Red Blue Green
Use
b and x to scroll to:
Press
t
Press t
Press t
Enter Input.
Press t
If ‘learnt’ is displayed
on an input, this will
need to be deleted
before learning can
begin. See page 12
for deleting inputs.
When ‘Learning’ is
displayed, press and
hold the ‘LEARN’
button on the device
until the LEDs cycle,
then release.
If the input device has
already been learnt to
the Enforcer system,
‘Input Learnt Already!’
will be displayed.
Press t

10
RADIO DEVICE
CONTROL?
Control Inputs?
Control Bells?
Learn Devices?
Select Bell
Available [1]
Select Bell
Learnt [2]
It is recommended that all wireless bells are learnt at
the Enforcer before any installation/mounting is done.
This makes learning much quicker.
A maximum of 2 wireless external bells (Deltabell WE)
can be connected to the Enforcer.
Even though the ‘learn’ may be successful, the
position of the bell box on a property must be tested
for signal strength before it is actually ‘xed’ into
place. Please see page 13 when analysing the
wireless range and signal strength.
Before learning each bell check that the battery is
present and is inserted correctly.
Follow the instructions to the right to start learning the
bells.
A bell that is learnt correctly will ash the GREEN LED
briey and display ‘Bell Learnt’ on the keypad. Both of
these instances need to occur to indicate a successful
learn.
D
A
B
C
SPACE 
1
4
7 8
5
23
6
9
0
,/+.
ABC
JKL
MNO
PQRS
TUV
WXYZ
DEF
GHI
BYP
Green
Blue
Red
Learning...
Bell Learnt
Bell Learnt
Already!
Use b and x to scroll to:
Press
t
Press x
Press t
Press t
Enter Bell.
Press t
If ‘learnt’ is displayed on
a bell, this will need to be
deleted before learning
can begin. See page
12 for deleting bells.
When ‘Learning’ is
displayed, press and
hold the ‘LEARN’
button on the bell until
the LEDs cycle, then
release.
If the bell device is already
learnt on the Enforcer
system, ‘Bell Learnt
Already!’ will be displayed.
Press t
Learning Bells