Pyronix EURO 46 V10 User manual

EURO 46 V10
Installation Manual
PD6662:2010+IA501:2015
EN50131-1:2008+A1:2009
EN50131-3:2009
Security Grade (SG) 3 - Large
Security Grade (SG) 2 - Small
Environmental Class (EC) II
RINS1941-2
Software Version >10

2
EURO 46 V10 Installation Manual

3
EURO 46 V10 Installation Manual
System Overview 4
Default Codes 4
Input Mapping 5
Output Mapping 6
Regulatory Wiring Requirements 6
Technical Specification 7
Out of the Box 9
The Printed Circuit Board 10
Communication Loom 11
Power and Battery Connections 12
485 Bus Wiring 13
Star and Daisy Chain Wiring 14
Input Connections 15
Output (PGM) Connections 16
Relay and Speaker Output 16
XPGM Outputs 16
External Sounder Connections 17
Grade 3 Wiring 17
Grade 2 Wiring 17
Modems 18
UDL Software 18
Connecting RS232 to the Panel 18
Connecting InSite to the Panel via RS232 19
Setting up a Cloud Connection 19
Connecting InSite to the Panel via the Cloud 20
EN 50131 Terminology 20
Access Levels 21
Compliance 21
Warranty 21
Additional Device Manuals 22
Wired Setting Devices 22
Wireless Setting Devices 22
Zone Expansion Modules 22
Output Expansion Modules 22
External Wired Sounders 22
Customer Support 23
Pyronix Training Academy Online 23
Pyronix Training Academy Training Videos 23
Technical Support 23
Contents

4
EURO 46 V10 Installation Manual
System Overview
System Overview EURO 46 V10 Additional Information
Areas
Independent areas 6
Wards 5 Each ward is created by a proximity reader
Inputs
On board 8 Supports N/C, 3EOL, DEOL and SEOL
Wireless 64 Requires 2 x EURO-ZEM32-WE
Maximum 76 Refer to ‘Input Mapping’ table
Outputs
PCB 5 1 Relay, 4 transistor (inputs 7 & 8 may be used as outputs)
AT E 10 Low power ATE outputs
Maximum 85 Refer to ‘Output Mapping’ table
User automation 30 Outputs programmed to activate on user command
Users
Users 75
Wireless key fobs 32 Requires 1 x EURO-ZEM32-WE
Guard/duress 10
Engineer 1
Maximum 87 Including Master Code and wireless key fobs
Arming Devices
Wired 6 Keypads and proximity readers
Wireless 4 Requires 1 x EURO-ZEM32-WE
Communication
Compatible modems PSTN, PSTN/VOICE, GSM, GPRS, Wi-Fi/XA and LAN
ARC formats Contact ID, Fast Format and SIA3 (also IP variants in all 3)
User formats Push notifications, SMS messaging and Voice messaging.
Phone numbers 10 Used for SMS messaging
UDL Support Ye s Using the upload/download software
Logs
Memory 1250 Memory type is EEPROM
Dimensions and Compliance
Dimensions
(H x W x D)
Small Case 297 x 250 x 82 mm
PCB 110 x 170 x 40 mm
Large Case 390 x 305 x 100 mm
EN grading 2 (small metal)
3 (large metal)
Environmental class II
Default Codes
Engineer - 1111
Master Manager - 2222

5
EURO 46 V10 Installation Manual
Input Mapping
Devices Address Input Numbers
EURO 46 V10 PCB N/A 1-8
EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 0 9-16
EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 1 17-24
EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 2 25-32
EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 3 33-40
EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 4 41-48
EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 5 49-56
EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 6 57-64
EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 7 65-72
EURO-LCD/EX 0 73-74
EURO-LCD/EX / EURO-PROX/INT 1 75-76
TOTAL 76
PLEASE NOTE: 2 x EURO-ZEM32-WE can be connected to the EURO 46 V10. Each expander
allows 32 inputs which are separated into 4 addresses (each address enables 8 wireless inputs). It is
possible to mix the wired and wireless remote expanders.
PLEASE NOTE: If the EURO-PROX/INT (Internal Tag Reader) is programmed as a ‘Set Point’ device,
2 inputs are enabled. If the EURO-PROX/INT is programmed as ‘Entry Control’ or ‘Access Control’
only 1 input is enabled.

6
EURO 46 V10 Installation Manual
Output Mapping
Devices Address Outputs Numbers
EURO 46 V10 APP PCB N/A 5 (2 shared)
Digi/ATE Outputs (using communication loom) N/A 10
EURO-OEM8R8T / EURO-OEM16R+PSU 0 1-16
EURO-OEM8R8T / EURO-OEM16R+PSU 1 17-32
EURO-ZEM8+/ EURO-ZEM8+PSU 0 1-4
EURO-ZEM8+/ EURO-ZEM8+PSU 1 1-4
EURO-ZEM8+/ EURO-ZEM8+PSU 2 1-4
EURO-ZEM8+/ EURO-ZEM8+PSU 3 1-4
EURO-ZEM8+/ EURO-ZEM8+PSU 4 1-4
EURO-ZEM8+/ EURO-ZEM8+PSU 5 1-4
EURO-ZEM8+/ EURO-ZEM8+PSU 6 1-4
EURO-ZEM8+/ EURO-ZEM8+PSU 7 1-4
EURO-LCD/EX 0 1
EURO-LCD/EX / EURO-PROX/INT / EURO-EXT-BK/W 1 1
EURO-LCD/EX / EURO-PROX/INT / EURO-EXT-BK/W 2 1
EURO-LCD/EX / EURO-PROX/INT / EURO-EXT-BK/W 3 1
EURO-LCD/EX / EURO-PROX/INT / EURO-EXT-BK/W 4 1
EURO-LCD/EX / EURO-PROX/INT / EURO-EXT-BK/W 5 1
Total 85
Regulatory Wiring Requirements
• Ensure wiring is done to the national wiring regulations in the country where the installation is
taking place. In the UK, this is BS 7671 Requirements for electrical installations; IET Wiring
Regulations (17th edition). If in doubt, consult a local qualified electrician.
• Ensure that a readily accessible disconnect device incorporated in the premises installation wiring
shall be provided external to the equipment with a contact separation of at least 3,0mm and
connected as closely as possible to the supply. Example: Fused Spur Unit
• When fixing external wires, ensure that means are provided in the installation to prevent the SELV
(Safety Electrical Low Voltage) or signal circuits from coming into contact with live parts of the
power supply circuit. Wires shall be fixed near their terminal blocks.
• The end of stranded conductor shall not be consolidated by soft soldering at places where the
conductor is subjected to contact pressure. Example: Must not solder ends of wires which are to be
secured in detector and control panel terminal connectors.
• On completion of wiring use tie-wraps to prevent any loose wires causing a safety hazard (material
of cables tie shall be rated at least HB or better).
• Cables ties and sleeves shall be separate for power supply cable and SELV (Safety Electrical Low
Voltage) wirings.
• Size of protective bonding conductors: minimum section 1.5mm². Example: Electrical Earth wire
connections.

7
EURO 46 V10 Installation Manual
Technical Specification
Programming Outputs Power Rating Normal State Active State
PGM 1 Relay, 3A, max 30V Changeover NC & NO Changeover NC & NO
Speaker 16 ohms No tones Repeat RKP tones & internal
sounder
Strobe output 500mA 12v 0v
Bell output 500mA 12v 0v
XPGM 1 (Input 7) 50mA Floating 0v
XPGM 2 (Input 8) 50mA Floating 0v
ATE outputs 2mA 5v 0v
Circuit States
Resistance Range
1k / 1k Range 4k7 / 2k2 Range 4k7 / 4k7 Range
Normal 0k5 to 1k4 1k4 to 2k9 3k7 to 8k3
Alarm 1k5 to 5k9 4k2 to 7k8 8k4 to 10k2
Fault 6k to 8k1 8k to 11k3 10k3 to 14k9
Masking 8k2 to 17k 11k6 to 22k 15k to 22k
Tamper <0k5 or >17k <1k4 or >22k <3k7 or >22k
Fuses Value Type
Bell fuse for bell terminals F800mA quick blow 250V Glass
Aux fuse for aux terminals F800mA quick blow 250V Glass
RS485 bus fuse for bus terminals F800mA quick blow 250V Glass
Battery fuse for battery terminals T 1.5A anti-surge slow blow
250V Glass
230V mains fuse for mains terminals T500mA H anti-surge slow
blow 250V Ceramic
Panel Power Supply Output Nominal Range
Output voltage ~13.7VDC ~10-15VDC
Output current
Small Metal 1A Continuous 1.5A peak, during battery
charging
Large Metal 1.5A Continuous 2.0A peak, during battery
charging
Panel Power Supply Input Nominal Range
Mains supply voltage AC 230 VAC at 50Hz -15% +10 %
Transformer rating
Small metal 18VA 18V at 1.0A
Large metal 45VA 18.5V at 2.5A
Power Supply Type A.
Maximum output peak voltage: Max 100 mV
SD Voltage which the deep discharge protection function will operate at: 10V
Over Voltage Protection Trigger Voltage: 18V
Battery Charging Specification
Float voltage 13.8VDC Recharge time <24 hours
Battery low voltage cut off 10.5V Standby battery capacity
current
300mA (3A to 6A)
700mA (7A to 17A)

8
EURO 46 V10 Installation Manual
PLEASE NOTE: EURO 46 V10 power supplies are NOT designed for use with multiple batteries
connected. System load should not exceed the panel power supply output shown above, or the
maximum load supportable by the battery for the specified backup time, as in the table shown below.
The power ratings are based on battery shown in table – but battery capable of supporting the
system load for the required time may be used without affecting these ratings.
EN50131-6:2008 Rated Output
In accordance with EN50131-6:2008, the EURO standby times and effective output currents depend on the Security Grade of the
system and how 230V mains missing fault is signalled to the Alarm Receiving Centre. Power supplies are rated in accordance with
the requirements of EN50131-6, which are related to the maximum battery size that can be accommodated in the housing and vary
according to the grade of the system in which they are installed, as per the following table:
Electrical Capability EN50131-6 Rating. Maximum Load
Example Battery Model Grade 2 Grade 3
Yuasa NP7-12 0.5A 0.3A
Yuasa NP17-12 1.2A 0.7A
EURO 46 V10 PCB Current Consumption Environmental
Quiescent 80mA Operational -10°C to +40°C, Certified
User Code and Tag Guessing Storage -20°C to +60°C
4-digit codes 10,000 Humidity 75%
6-digit codes 100,000 Dimensions
Disallowed codes None
Metal case
Small case 250 x 297 x 82mm
Weight: 4.8kg inc. battery
All codes 1612 Large case 390 x 305 x 100mm
Weight: 11.5kg inc. battery
According to EN50131-3:2009 Annex B PCB 170 x 90 x 30mm
According to spec of manufacturer of RFID components used EN50131 Grading 3
The below table specifies ATS (Alarm Transmission System) performance criteria in accordance with
the requirements of EN50136-1.
Notification Equipment
Grade 2 Criteria Grade 3 Criteria
Options Options
A B C D A B C D
Remotely powered external sounder 2Optional Optional Optional 2Optional Optional Optional
Self-powered external sounder Optional 1Optional Optional Optional 1Optional Optional
Main communication path (ATS) ATS 2 ATS 2 ATS 2 ATS 3 ATS 4 ATS 4 ATS 4 ATS 5
Second communication path (ATS) Optional Optional ATS 1 Optional Optional Optional ATS 3 Optional

9
EURO 46 V10 Installation Manual
Out of the Box
Unscrew and remove the cover of the EURO 46 V10 (Figure
1). The EURO 46 V10 printed circuit board is located to the
top right hand side. (Figure 2)
Install the supplied stand-offs if needed before mounting the
metal case to the wall (Figure 3).
Connect any modems if required and any other devices
(input expanders, output expanders etc.) before powering up
the system.
Screw the back metal plate to the wall.
Wire the telephone line if the DIGI-1200 modem (PSTN) is
installed or the LAN cable if the DIGI-LAN is installed.
Install the SIM card, connect the antenna and locate outside
of the metal casing if the GPRS or Wi-Fi modem is used.
EURO 46 V10: The tamper mechanism comes already fitted.
Figure 1
Figure 2
Figure 3
Secure all the wires and close the enclosure making sure the
tamper is operational.
Turn on the power to the EURO 46 V10.
On power up, the panel will typically show the below screens.
485 COMMS FAIL >>PLEASE WAIT<< EURO 46 V10
Time 10:09 c

10
EURO 46 V10 Installation Manual
The Printed Circuit Board
1: Case tamper ‘Hold-Off’ jumper
2: PGM 1
3: Speaker connection
Connects a 16ohm speaker.
4: External sounder connections
Connects an external sounder.
5: Input connections
8 Fully programmable inputs.
6: Tamper switch
Optional tamper protection for the metal casing.
7: Auxiliary 12V power
12V power supply
8: Inputs or outputs
Inputs 7 and 8 may be programmed as outputs
if unused.
9: Battery connect ‘Kick-start’ switch
To power-up and program from battery power
(when there is no mains power available).
10: RS485 bus terminals
Connects peripherals.
11: Battery connection
For battery back up.
12: Earth connection
Connects the earth.
13: 17V connection
Connects the AC transformer 17V supply.
14: Battery charge capacity jumper
For battery back up.
15: Modem connections
The left connector (labelled ‘modem’) is for
signalling modems.
PLEASE NOTE: The right is ‘For Future Use’,
please do not use.
16: RS232 Connection
This connection is used for an RS232 lead that
will connect to a PC to allow uploading and
downloading of data using the InSite software.
17: Communication Outputs
Connects the supplied communication loom to
enable an additional 9 programmable outputs.
These are low current and would normally
be used when connecting a stand-alone
communicator to the panel.
18: Bell Fuse
19: Auxiliary Fuse
20: Bus Fuse
21: Battery Fuse
MODEM FOR FUTURE
USE

11
EURO 46 V10 Installation Manual
Communication Loom
PLEASE NOTE: The polarity of the ATE outputs can by changed in the Engineer Menu. The menu
option is named ‘Invert ATE O/Ps’ and can be found as a sub menu in ‘SYSTEM OPTIONS’ then
‘Site Options’. This will invert the polarity of all the programmable ATE outputs, they cannot be done
individually.
Normal Status: 5v
Active Status: 0v
Current: 2mA
The ATE (Alarm Transmission Equipment) outputs are programmed in the Engineer Menu. The
programming can be found in ‘CHANGE OUTPUTS’ then sub menu ‘Endstation Outputs’.

12
EURO 46 V10 Installation Manual
Power and Battery Connections
2-6Ah 7-17Ah
Panel Power Supply Input Nominal Range
Mains Supply Voltage AC 230V AC at 50Hz -15% +10%
Transformer Rating 18VA 18V at 1.0A
Panel Power Supply Output Nominal Range
Output Voltage 13.7V DC 10-15V DC
Output Current
Small Metal 1A Continuous 1.5A peak, during battery charging
Large Metal 1.5A Continuous 2.0A peak, during battery charging
Power Supply Type A.
Battery Charging Specification
Float Voltage 13.8v DC Control Panel Type
Battery low voltage cut off 10.5v Standby battery capacity current 300mA (3Ah to 6Ah)
Recharge time <24 Hours Standby battery capacity current 700mA (7Ah to 17Ah)
Fuses Value Type
230V Mains Fuse for mains terminals T500mA H anti-surge slow blow 250V Ceramic
PLEASE NOTE: Ensure that the ‘battery jumper’ is in the correct position for the capacity of battery
that you have connected – otherwise the panel may under-charge a large battery or over-charge and
damage a smaller battery.
EURO 46
Time 10:09 c

13
EURO 46 V10 Installation Manual
485 Bus Wiring
8
2
All 485 bus peripherals; LCD
keypads, readers, expanders etc.
are connected via the D1-, D2+,
D3 and D4 terminals. This is an
example of what a typical 485 bus
may look like.
General Principles:
NOTE 1: No alarm system cable
should be run with other cables
carrying AC or digital signals.
NOTE 2: The cables should be
protected by the use of grommets
where appropriate.
NOTE 3: For greater than 1000m
range a standard isolated RS485
repeaters required.
NOTE 4: There must be a ferrite
bead fitted to one of the outgoing
data lines and secured inside
the EURO 46 V10 case itself. The
Ferrite bead is supplied packaged
with a cable-tie which must be
used to secure it in the case and
prevent it shorting any electrical
contacts (Ferrite as shown).
There must also be a ferrite bead
fitted to the data wires of a EURO-PROXE (if connected). The Ferrite bead is supplied with the reader.
NOTE 5: If an expansion module with a power supply on board is connected,
the D2+ terminal must not be connected between the main bus and module.
EURO 46
Time 10:09 c

14
EURO 46 V10 Installation Manual
Star and Daisy Chain Wiring
Cable Type Screened Cable Bus Range (m)
Wiring Format
Star Wiring Range Daisy Chain Range
4 core alarm cable
Use this type of cable
when the wiring of the
485 bus is located near
230VAC mains power
wiring
300
50 m 1 km
6 core alarm cable
(doubling D1 (0v) and
D2 (+12V))
1000
Twisted Pair 1000
Star Wiring Example
Daisy Chain Wiring Example

15
EURO 46 V10 Installation Manual
Input Connections
PLEASE NOTE: If ‘Normally Closed’ (double pole) wiring is utilised, The EOL range must be set to
‘4k7/2k2’ and the EOL mode set to ‘DR’. This can be selected in the Engineer Menu in the menu
‘CHOOSE MODE’. The ‘Diagnostics’ on the keypad will show 6K9 when the alarm circuit is open and
2K2 when the alarm circuit is closed. It will show >22k when the tamper circuit is open.
The EURO 46 V10 has options of 4k7/2k2, 4k7/4k7, 1k/1k and wide EOL ranges to choose from. The
tolerances for each of these ranges can be found in the technical specification. The ‘wide’ range has
no masking tolerance range. This is added on to the end of the alarm tolerance in order to create a
wider alarm tolerance range.
EURO 46 V10 panels are set to 4k7/2k2 at default and would typically used a 2k2 resistor for tamper,
4k7 resistor for alarm and finally a 6k8 resistor for mask.
For specific wiring instructions please refer to the installation manual provided with each component
that is being wired to the system.

16
EURO 46 V10 Installation Manual
Output (PGM) Connections
16 Ω
+
+-
-
0v
MODEM
Relay and Speaker Output
XPGM Outputs
+-
+
-
If Inputs 7 and 8 are programmed as ‘unused’, these inputs can be used as 2 further outputs (known
as XPGM1 and XPGM2). Which are programmed in ‘CHANGE OUTPUTS’ in the Engineer Menu.
Normal State: 12V
Active State: 0V
Current: 50mA switched
to 0V
Normal State: Floating
Active State: 0V
Current: 100mA

17
EURO 46 V10 Installation Manual
External Sounder Connections
Grade 3 Wiring
Grade 2 Wiring
6K8
G2G3
FOR FUTURE
USE
G2G3
2
FOR FUTURE
USE

18
EURO 46 V10 Installation Manual
Modems
UDL Software
There are 6 modems there are compatible with the EURO 46 V10 panel. These are:
• DIGI WIFI/XA
• DIGI LAN
• DIGI GPRS
• DIGI GSM
• DIGI 1200
• DIGI PSTN/VOICE
For installation instructions please refer to the manual provided with the modem.
For programming instructions please refer to the ‘Communications Guide’.
PC
COM PORT
A USB/Serial converter is available from
Pyronix
Connecting RS232 to the Panel
Enter the Engineer Menu.
Scroll the menu (button) until the ‘SET UP DOWNLOADING?’ and press .
Choose RS-232 in the “Download by” option – Press .
Now on the ‘UDL Password’ screen, leave ‘blank’ and Press .
Now on the ‘Site Name’ screen, this is compulsory, make sure that you take a note of it for use later in
the InSite software then press .
Now on the ‘UDL Priority’ screen – we recommend setting this to ‘High [0]’.
PLEASE NOTE: This prevents HomeContol+ App events / notifications from disconnecting the UDL
connection.
The EURO 46 V10 control panel can be programmed by the LCD menu or the UDL InSite Software,
provided free of charge. It can be downloaded from https://www.pyronix.co.uk/help-and-support/
installers-distributors/insite-software-download/insite-software-download. The connection between
control panel and UDL software can be done in the following ways:

19
EURO 46 V10 Installation Manual
Connecting InSite to the Panel via RS232
Setting up a Cloud Connection
To setup the COM port associated to ‘modem’, open the software, click on ‘Configuration’, choose
“Modem Settings” and select “RS-232” option.
Make sure that the serial COM port used by UDL is the set the same in the PC.
PLEASE NOTE: This can be found in the PC via Control Panel > Device Manager > Ports.
Make sure that in the UDL Graphic user interface, the RS-232 icon is green.
Click on ‘Roving Dial Customer’.
Set ‘Dial Mode’ field to ‘RS-232’.
Enter the Engineer Code in the ‘Engineer Code’ field.
Click on ‘Dial’.
If connection is successful, the RS-232 icon will become blue.
Enter the Engineer Menu.
Scroll the menu (button) until the ‘SET UP DOWNLOADING?’ and press .
Choose ‘Cloud’ in the ‘Download by’ option – Press .
Make a note of your ‘System ID’ (to enter in the InSite software later) - Press .
Select Security level – for initial connections we recommend [0] (normal) - Press .
Create/enter a system password and take note of it - Press .
Now on the ‘Poll Server’ screen – select ‘Yes [1]’ and press .
Now on the ‘UDL Password’ screen – DO NOT USE – leave blank and Press .
Now on the ‘Site Name’ screen, this is compulsory, make sure that you take a note of it for use later in
the Insite software then press .
Now on the ‘UDL Priority’ screen – we recommend setting this to ‘High [0]’.
PLEASE NOTE: This prevents HomeContol+ App events / notifications from disconnecting the UDL
connection.

20
EURO 46 V10 Installation Manual
Connecting InSite to the Panel via the Cloud
Click on ‘Roving Dial Customer’.
Click on the ‘Dial Out Mode’ drop down list and select ‘Cloud’.
Enter the ‘System ID’ of your panel (see ‘SET UP DOWNLOADING?’ in the panel Engineer Menu).
Enter ‘System Password’ (see ‘SET UP DOWNLOADING?’ in the panel Engineer Menu).
Leave the UDL security at ‘normal’ for initial connection test in ‘System Security Level’ field.
Enter the Engineer Code as used on the panel you are trying to connect to.
Enter ‘Site Name’ as entered in panel.
Enter an appropriate panel name into the ‘Enter Customer In Database As’ field.
PLEASE NOTE: This is just for identification in the InSite software, nothing more.
Click ‘Dial’. If connection is successful, the Cloud Icon will become blue, and a dialogue box will
appear asking if you would like to create a customer – click ‘Yes’ to continue.
The EURO 46 V10 control panel is now successfully connected to the Insite UDL software.
EURO 46 V10 Language EN50131 Language
Set Set
Unset Unset
Day or Unset Mode Unset State (may be relevant to a specific partition)
HU (Hold Up) Hold Up (HU)
Inhibit Inhibit
Unused Isolated
Bell / External Sounder / SAB External Warning Device (self-powered is assumed)
Main Sounder / Speaker Device combining internal warning device with audible
indicator (using different tones and volumes)
Prox card, Tag, or Wireless Key Fob Digital Key
EN 50131 Terminology