Pyronix PCX 46 User manual

T
h
t
e
e
x
h
e PCX is
c
e
chnology
x
pander).
compatib
l
using th
e
l
e with th
e
e
PCX-RIX
3
e
Enforce
r
3
2-WE (E
n
PCX 46
r
wireless
n
forcer w
i
Eng
Lar
g
e
i
reless
ineer
P
C
>So
f
Refe
r
CX
PCX 46
S
f
tware R
e
r
ence
X
4
S
mall
RINS160
6
vision V9
.
Man
u
6
6
-4
.
26
u
al

PCX 46 Programming Reference
Page: 2
1. Contents Page
1. Contents Page ........................................................................................................................................ 2
2. Introduction ........................................................................................................................................... 3
2.1 Hybrid Integrated System with Automation Control ................................................................................. 3
2.2 2-Way Wireless Technology.................................................................................................................. 3
2.3 User Automation Outputs..................................................................................................................... 3
2.4 SMS Text Alarm Notifications................................................................................................................ 3
2.5 Total System Remote Control with a SMS Remote Phone Application .......................................................... 3
3. Keypad Operation.................................................................................................................................... 4
4. The Engineer Menu .................................................................................................................................. 5
4.1 Navigating in the Engineers and User Menu ............................................................................................ 5
4.2 Entering The Engineer Menu (Default Engineer Code = 9999) ................................................................... 5
4.3 Exiting The Engineer Menu................................................................................................................... 5
4.4 Accessing the Engineers Menu on any external wired keypad .................................................................... 5
4.5 Saving Your Programming.................................................................................................................... 5
5. Engineer Menu ........................................................................................................................................ 6
5.1 Bypass Fire & PA? ............................................................................................................................... 6
5.2 Date and Time? .................................................................................................................................. 6
5.3 Learn Wireless Devices? ...................................................................................................................... 6
5.4 Program Inputs?................................................................................................................................. 9
5.5 Program EOL? ...................................................................................................................................13
5.6 Install RIXs? .....................................................................................................................................13
5.7 Program Outputs?..............................................................................................................................13
5.8 Install Keypads and Readers? ..............................................................................................................16
5.9 Program Timers? ...............................................................................................................................18
5.10 Change Codes?................................................................................................................................19
5.11 Exit Modes? ....................................................................................................................................21
5.12 System Options?..............................................................................................................................21
5.13 System Displays ..............................................................................................................................23
5.14 Volume Control? ..............................................................................................................................24
5.15 Review Logs? ..................................................................................................................................24
5.16 Diagnostics?....................................................................................................................................25
5.17 Engineer Tests? ...............................................................................................................................26
5.18 Engineer Restore Options? ................................................................................................................27
5.19 Digi Modem Signalling?.....................................................................................................................27
5.20 Alarm Responses?............................................................................................................................31
5.21 Options Up/Downloading? .................................................................................................................32
5.22 PC Connect Menu? ...........................................................................................................................33
5.23 Software Revision?...........................................................................................................................33
5.24 Factory Default? ..............................................................................................................................34
5.25 Exit Engineer Menu?.........................................................................................................................34
6. Adding External Wired Keypads ................................................................................................................35
7. Options Programmable Only From PC ........................................................................................................36
7.1 Auto Arm/Disarm Timers ....................................................................................................................36
7.2 Areas to Arm/Disarm .........................................................................................................................36
7.3 Programming Logic Gates ...................................................................................................................37
8. Faults and Troubleshooting ......................................................................................................................38
8.1 Device Fail / Active Faults ...................................................................................................................38
8.2 System Faults and Troubleshooting ......................................................................................................38
9. Event Types ..........................................................................................................................................42
10. Contact ID & SIA reported events ...........................................................................................................45
11. EN 50131 Terminology ..........................................................................................................................47
12. Access Levels.......................................................................................................................................47
13. Factory Defaults ...................................................................................................................................48

PCX 46 Programming Reference
Page: 3
2. Introduction
2.1 Hybrid Integrated System with Automation Control
The PCX 46 is hybrid alarm system. It integrates the award winning Enforcer Two Way wireless
technology with 30 automation outputs and a host of high security features. The PCX 46 is easy to use
and designed to communicate to you about any system activations via SMS messages. It also can send
alarms to the Alarm Receiving Centre and maintenance company.
2.2 2-Way Wireless Technology
Using the wireless input expansion module RIX 32-WE, the PCX 46 converts into a high security wireless
system taking full advantage of Pyronix’ innovative wireless technology using the Pyronix High Security
Wireless Encryption Protocol. This module also allows the access to all Enforcer system 2-way wireless
peripherals.
No inhibitions: The two way wireless movement detectors are fully operational when the system is
armed, making your system more secure, compared to other wireless systems, where devices are
disabled for up to five minutes after every activation to save battery, therefore compromising your
security.
Battery Monitoring/Saving: The Enforcer wireless system uses advanced technology to preserve the
battery life of each wireless device. However, the system informs you when a battery needs replacing a
month in advance before the device stops working. This key feature gives you enough time to change
the battery in the specific device. Other wireless alarm systems may not give you a low battery warning
signal, meaning that devices could stop working, leaving your environment unprotected.
High Security Encryption: The wireless protocol is encrypted with 128 bit making it impossible to
replicate or copy its wireless peripherals. It also uses an intelligent wireless jamming detection
technology.
User Friendly Keyfobs: Up to 32 wireless keyfobs can be added to the PCX 46 system. Each wireless
keyfob has its own user ID which can be reported to the ARC and user mobile phone. It is possible to
allocate different functions to each keyfob such as arming / disarming different areas, activating the
automation outputs to control external devices such as gates, requesting system status, and activating
panic alarms giving you total control of your system. It shows you the system status using a 3 colour
LED:
System armed: When the system is armed a RED LED will illuminate momentarily.
System disarmed: When the system is disarmed a GREEN LED will illuminate momentarily.
System fault: When the system is in fault condition an AMBER LED will illuminate.
2.3 User Automation Outputs
The PCX 46 has ability to operate up to 30 user automation outputs that give you the option activate
gates, lights, sprinklers, etc. via your keypad, wireless keyfob or smart phone app.
2.4 SMS Text Alarm Notifications
When your system is activated it will notify you via SMS text messages in real time. For example,
notification that your child has returned home from school safely or notification of a leakage of water in
your property etc.
2.5 Total System Remote Control with a SMS Remote Phone Application
The PCX system can be remotely controlled by using a smart phone app. It allows you to arm, disarm
PCX 46, check the system status and bypass inputs. It also allows you to activate remotely up to 30
devices such as gates, lights, sprinkles and others. The remote control app is available in several
languages.

PCX 46 Programming Reference
Page: 4
3. Keypad Operation
On the PCX 46 it is possible to write your own texts for the following:
-Inputs, Input Number, Location
-Area Names
-Site Name
-Keypad/Reader, Keypad Number, Location
-Input and Output expander location descriptions
-User Names
The PCX 46 incorporates a predictive text feature (T9 type). For example, if you enter ‘B’ ‘Bedroom’ will
be displayed. If the word that you require doesn’t appear on the LCD display, just type the word letter by
letter. To type a word, press the relevant button the appropriate number of times – e.g. for the letter ‘k’
press the 5key two times, or for the letter ‘s’ press the 7button four times. For punctuation marks,
press the 1button.
Buttons meaning:
The following alpha-numerical buttons are used Other meaning of the buttons
a= make the character into a capital a= Status Area A
c= clears letters / adds a space b= Status Area B
[= moves cursor left c= Status Area C
]= moves cursor right d= Status Area D
d= Press to Enter Manager Mode
f= Press for 2 sec to generate Fire alarm
p= Press for 2 sec to generate PA alarm

PCX 46 Programming Reference
Page: 5
4. The Engineer Menu
The system is programmed from the Engineer Menu. To enter the Engineer Menu the panel must be fully
disarmed state. Whilst in Engineer Mode all tamper alarms (including case tamper), will be disabled.
4.1 Navigating in the Engineers and User Menu
x= “NO” - Press to move forward when in Engineer or Master Manger mode
b= “BACK” - Press to move backward when in Engineer or Master Manger mode
t= “YES” - Press to enter in a submenu or option when in Engineer or Master Manger mode
t= Press to move from one option into another option while in a submenu
a= Press to quick exit the Engineer Menu from any main menu (written in capital letters)
c= “CANCEL” - Press to move back from one programmable option to the previous option.
4.1.1 Main Menus and Sub Menus
You are in a main menu item if:
The maintenance LED is flashing slowly
The menu item will be in capital letters
You are in a sub menu item if:
The maintenance LED is flashing rapidly
The menu item will be in small letters with a
question mark (?).
In order to navigate in the menu system one has to answer the questions in the main and sub menus.
For example, if the question is “LEARN WIRELESS DEVICE”. Pressing twill bring you in the sub-
menu “Control Inputs?” Pressing twill take you to the programmable options of this submenu.
Pressing xwill take you out of the individual option, will move you up from one sub-menu to the
next sub-menu or back to the main menu.
NOTE: For your security, the keypad becomes disabled for 90 seconds after 16 incorrect key-presses,
or after 6 attempts to present invalid tags. It will subsequently be disabled again after 7 further
incorrect key-presses or after another invalid tag is presented. Once a correct code or tag has been
registered, the keypad is returned to normal operation. PIN code entry must be completed within 60
seconds or it will count as an invalid code being used.
4.2 Entering The Engineer Menu (Default Engineer Code = 9999)
Access maybe denied if: 1) One or more areas are armed.2) The Master user has disabled the access of
the Engineer Menu from “Allow Engineer Menu” in the Master Manager Mode. If this is the case
‘Authorization required’ will be shown on the display. After entering the Engineer code 9999 (default
code) the first option that is shown will be: Arm System? This option will enable the Engineer to Arm
the panel once maintenance work is finished. The system can also be disarmed by the engineer if it was
armed with an engineer code. Press tto arm the system or press xto enter the Engineer Menu.
When in Engineer Menu, the fault () LED will flash and high pitch tone will be generated regularly.
4.3 Exiting The Engineer Menu
On completion of programming, the system can be returned back to disarmed mode by either scrolling to
the ‘Exit Engineer Menu’ option or press the abutton from any main menu option (represented in
capital letters).
4.4 Accessing the Engineers Menu on any external wired keypad
It is possible to access the Engineer Menu on any keypad that is part of the system. If you are in the
Engineer menu in keypad address 0, the other keypads will display ‘system busy’. To access the
Engineer menu on a different keypad, press the bbutton on the relevant keypad.
4.5 Saving Your Programming
Any programming done in the engineer or user mode will not be saved on the system until the Engineer
or User menu have been exited.

PCX 46 Programming Reference
Page: 6
5. Engineer Menu
Please refer to the Engineer Programming Quick Guide for this chapter. The meaning of every option
presented in the quick programming guide is explained here in detail.
5.1 Bypass Fire & PA?
While in the Engineer menu the Fire and Personal Attack inputs/keypad alarms remain active. This
function allows you to disable these alarm activations until you exit the engineers menu.
5.2 Date and Time?
All log entries and the system display include the time and date. This may be also programmed in the
Master Manager Mode.
NOTE: Please note that powering down the system and removing the battery will reset the time and
date information.
5.2.1 Change Month
For March, enter 03
5.2.2 Change Day
For 31st, press 31
5.2.3 Change Hours
Use 24 hour clock format. For 8pm press 20:00.
5.2.4 Change Minutes
For 7:30, enter 30.
5.2.5 Software Clock Adjust
If enabled, the control panel will adjust the clock correctly if the control panel gains or loses time.
NOTE: This option is used in conjunction with the “System Options” , ‘Software Clock’ function.
5.2.6 Summer Time Adjust
If activated this option will automatically change 1 hour ahead and backward for the summer and
winter time.
5.3 Learn Wireless Devices?
This function should only be used if a PCX-RIX32-WE (Enforcer wireless expander) is connected to the
PCX 46. Please see the Installation Reference on how to connect this expander.
This menu learns or deletes wireless devices for the inputs and sirens.
NOTE: The keyfobs are learned and programmed from the Master Manager menu.
5.3.1 Learn Inputs?
Learn Devices?
This menu allows you to start the procedure of learning wireless inputs onto the system.
Choose Input
Use this menu to choose which input on the system you wish to learn. ‘Learnt’ will be displayed if a
device is already learnt, or ‘Available’ will be displayed if it is not.
Choose InputLearning…
1) Take the wireless device, and open the casing
2) Remove the plastic insulation between the battery and terminal.
3) If a Device is not learned = The Green and Red LEDs on the Device will flash alternate.
4) Press and hold the ‘learn’ button on the Device = The 3 LEDs will start cycling.
5) Release the ‘Learn’ button = ‘Input Learnt’ will be displayed and confirmation tone on the panel will
be emitted.
6) If an input has already been learnt, ‘Input learnt already’ will be displayed.
Example: The image below shows how to learn a MC contact. The same procedure is done for the
inputs and sensors. Please note if smoke or carbon monoxide sensors are learnt, they will just include
one multicolour LED.

PCX 46 Programming Reference
Page: 7
Delete Devices
Already learnt inputs may be deleted from this menu.
Delete All Enter Code
To delete all wireless input devices enter ‘2000’ (this is the PCX 46 Security Code). “Please wait” will
be displayed while the PCX 46 deletes ALL the wireless devices learnt on the inputs.
Choose Input to Delete
This option allows you to delete only a specific wireless device learnt to an input. Any inputs that
display ‘learnt’ can be deleted. “Please wait” will be displayed while the PCX 46 deletes the wireless
device. Return to this process to delete more devices.
5.3.2 Learn Bells?
Learn Devices
Entering this menu allows you to start learning wireless bells onto the system
Select Bell
Use this menu to choose which bell on the system you wish to learn. ‘Learnt’ will be displayed if a bell
is already learnt, or ‘Available’ will be displayed if not.
Select BellLearning…
1) Open the bell
2) Plug the battery connector into the battery terminal.
3) If a Device is not learned = The Green and Red LEDs on the Device will flash alternate.
4) Press and hold the ‘learn’ button on the Device = The 3 LEDs start cycling around.
5) Release the ‘Learn’ button = ‘Bell Learnt’ will be displayed and confirmation tone on the panel will
be emitted.
If a Bell has already been learnt, ‘Bell learnt already’ will be displayed.
LEARN
>5s
LEARN
>5s

PCX 46 Programming Reference
Page: 8
Delete Devices
Already learnt bells may be deleted by entering this menu.
Delete All Enter Code
To delete all wireless Bells enter 2000 security code. “Please wait” will be displayed while the PCX 46
deletes them.
Choose Bell to Delete
This option allows you to delete only a specific wireless Bell learnt. Any Bells that display ‘learnt’ can
be deleted. “Please wait” will be displayed while the PCX 46 deletes the wireless Bells. Return to this
process to delete more devices.
Learn Keyfobs Procedure
The keyfobs are learnt and deleted from the Master Manager menu.
Learn Keyfobs
1) Enter Master Manager Menu (Default Master Code = 1234).
2) Scroll to the “Change Codes” option.
3) Choose a code to allocate the keyfob to.
4) If a keyfob, code or tag are not learnt the space, between brackets will be empty.
5) If a keyfob, code or tag is learnt between the brackets will be shown [******].
6) Press and hold any of the keyfob buttons for 5sec.
7) A confirmation tone will be emitted and keyfob will be shown on the display.
Proceed with the programming of the keys shown next.
Delete Keyfobs
1) Enter Master Manager Menu (Default Master Code = 1234).
2) Scroll to “Changes Codes” option.
3) Choose the keyfob to delete = between the brackets will be shown [******].
4) Press c. Between the brackets will be shown [ ] to confirm the deletion.
.

PCX 46 Programming Reference
Page: 9
5.4 Program Inputs?
By default, all inputs are set to ‘unused’. Before programming, identify input type required:
No Input Types Operation
0 Unused Factory default. Input is disabled.
1 Fire Active at all times. Audible Response: Differentiated Internal sound.
Pulsed external sound.
Communicator: ‘Fire’ signal
2 Gas Active at all times. Audible Response: Full external + Internal sound.
Communicator: ‘Gas’ signal
3 PA#Active at all times. Audible Response: Differentiated Internal sound. Full
external sound.
Communicator: ‘Personal Attack’ and ‘Input PA’ signals
4 Silent PA#Active at all times. Audible Response: None
Communicator: ‘Personal Attack’ and ‘Input PA’ signals
5 Tamper When disarmed: Audible Response: Internal only.
Communicator: ‘Tamper’ signal.
When armed: Audible Response: Full external + Internal sound.
Communicator: ‘Tamper’ signal.
6 Instant Active when armed: Audible Response: Full external + Internal sound.
Communicator: ‘Burglary’ signal
7 Entry Delay1#$ Active when armed: Initiates entry timer 1 when door open. If system not
disarmed before entry time expires then:
Audible Response: Full External + Internal sound.
Communicator: ‘Burglary’ signal
NOTE: See type 43 for Entry Delay2
8 Follow$Active when armed, except during entry time. (Acts as an instant input if
an Entry Delay input hasn’t been activated beforehand)
Audible Response: Full external + Internal sound.
Communicator: ‘Burglary’ signals.
11 Push To Arm Active during exit time, to complete arming procedure. No audible or
communicator response. Panel will communicate a final armed event once
the Push to Arm button has been pressed.
NOTE: May be used to act as ‘doorbell’ by use of ‘chime’ input attribute.
Example: Wire the Door Bell button to the input. Enable “Push to Arm”
option from “EXIT MODES”, add a “Push to Arm” input type to the input
and enable the “Chime” attribute for it.
Enter user code, the panel starts arming. Exit the building and close the
door. Press the Bell button. The system will arm. If pressing the Bell
button while the panel is in any other condition the Chime will sound.
12 Switcher Active at all times in armed and disarmed modes. No audible or
communication alarms will be created.
When activated it can trigger associated output for switching external
equipment. If the “Special Log” attribute is enabled for this input an SMS
message will be sent each time the input is activated.
Example:
This kind of input type can be used to control CCTV. The concept is that
when a switcher input type is activated, there is an output associated with
it following that input (the most used solution is the use of output type –
0035). The switcher input is connected to a detector located next to a
CCTV camera and the output is connected to a video recording /
transmitting equipment.
If the detector is activated in armed or disarmed mode then the recording
or transmission will start.
13 24 Hour When armed: Audible Response: Full External + Internal sound;
Communicator: ‘24hr Alarm’ signal.
When disarmed: Audible Response: Full External + Internal sound;
Communicator: ‘24hr Alarm’ signal if enabled in “Alarm Responses” menu.

PCX 46 Programming Reference
Page: 10
15 Sub Area
Control
Active when armed or disarmed. Communicator: Sub-area
Armed/Disarmed event (CID 402/401). Sub Area may be armed or
disarmed by proximity tag or input where a keyswitch can be wired. To
each sub area can be allocated a number of inputs creating the subarea
configuration.
16 Fault Active when armed or disarmed: Audible Response: internal sounder.
Communicator: Fault event.
If armed only: Activates ‘Global Fault 1’ output type.
If disarmed or armed: Activates ‘Global Fault 2’ output type.
Note that the ‘Technical Fault’ output type is triggered every time a fault is
active including when the fault input type is active.
17 Arming
Control
Active during arming procedure: No audible or communicator response.
Prevents system being armed whilst the input is in active state.
18 Shunt Active at all times: No audible or communicator response.
It is possible to associate inputs to the shunt input. It normally is
connected to a key-switch (or equivalent) and when On or Off it shunts or
un-shunts the inputs assigned to it. Associated outputs are available to
follow this input type.
Creating a Shunt Group: A shunt group may consist of any number of
inputs programmed as Instant, Tamper, 24hr and Follow types. These
must all be allocated in the same area.
NOTE: These inputs will need to be programmed before allocated to the
shunt input.
The inputs in the shunt group/list will only activate after 10 seconds of the
nominated shunt input.
Example: If input 1 is programmed as ‘Shunt Input’, and inputs 2 and 3
are programmed as “24hr”, then once input 1 has been opened, after 10
seconds inputs 2 and 3 become active.
Action 1: Shunt Input closed
Status: Inputs within the shunt list are Shunted ( Disarmed)
Outputs: ‘Follow Input’ PGM output On
Action 2: Shunt Input opened
Status: After 10 seconds inputs in the shunt list are going to activate, i.e.
become Un-shunted (Armed)
Outputs: ‘Follow Input’ PGM output OFF. The ‘Shunt Fault’ PGM output is
on for 10 seconds.
Action 3: Shunt Input opened with active detector from the shunt list
Status: After 10 seconds inputs in the shunt list are going to activate, i.e.
become Un-shunted (Armed)
Outputs: ‘Follow Input’ PGM output OFF. The ‘Shunt Fault’ (type 36) PGM
output pulses until the detector closes.
19 Disarm Only* Active when armed: Accepts input from keyswitch (or equivalent) to
disarm the area(s) assigned to it.
20 Keyswitch
Latched*
Accepts input from keyswitch (or equivalent) to arm/disarm the area
assigned to it. Arming includes normal exit time, etc. Requires latching
switch action. Normal operation is open circuit to arm the system, and
close circuit to disarm the system.
21 Entry Shock Active when system armed: This input type is advised to be used in
conjunction with an Entry Delay input. The Entry Delay input is a door
contact on the initial entry door, and the Entry Shock input is a non-
latching shock sensor fitted to the door frame in the vicinity of the lock. If
the door is forced a Burglary alarm will be generated immediately instead.
22 Line Fault Active when fail. This input type is used to detect external transmission
equipment line fail (output). If activated will give a line fault alarm, and
will signal telecom line fault on expiry of line fault timer. It can be used in
conjunction with CCTV input (type 39)
23 Keyswitch
Pulsed*
Accepts input from keyswitch to arm/disarm the area(s) assigned to it.
Requires momentary action switch to toggle arm/disarm state.
Note that Grade 1 operation only allows arming from the push button, but
requires means to abort arming (not to disarm)

PCX 46 Programming Reference
Page: 11
29 Interior This will work the same as an instant type input, the only difference is that
when CID reporting is programmed then any inputs that are programmed
as Interior will report CID event 132.
32 Flood This input type will work as a 24hr input, any inputs that are programmed
for Flood will activate the external siren and will report CID event 113.
39 CCTV Active at all times: No audible alarm or communicator response.
The CCTV input should be connected to an external detector located next
to a CCTV camera. An output can be programmed to follow this input and
the output should be connected to a CCTV recording, transmission or other
device. An input programmed as “Line Fault” (input type 22) should also
be connected to an output of the CCTV transmission Device. If the CCTV
transmission line has been cut or missing the ‘Line Fault’ input will
activate. Following to this at each activation of the CCTV input the panel
will signal CID events for ‘Silent Burglary’ and Line Fault. No audible alarm
will be created. If the Line Fault is not active it will just log the activations
of the CCTV input into the event log.
40 Perimeter This will work the same as an instant type input, the only difference is that
when Contact ID reporting is programmed then any inputs that are
programmed as Perimeter will report Contact ID event 131.
41 Patrol /
Keybox
This input type will work similar to a switcher input, it does not trigger an
alarm but will report Contact ID event 250 and is also a useful input type
when an output is required to follow the Keybox type input.
42 Medical This is a 24 Hrs type input it will activate the external sounder and report
a Contact ID event 100.
43 Entry Delay 2$Any input programmed as Entry Delay 2 will act as input type 07, but the
associated entry timer will use Entry Timer 2, rather than Entry Timer 1.
#These inputs cannot be bypassed.
*Use of inputs 19, 20 and 23 will make the system unable to comply with EN50131-1 Security Grade 2
or 3.
$ Ensure that these inputs are used on an entry/exit route
Choose Input
Choose an input to program.
Input In Area
Enter the areas you would like the input to operate in.
Common Input
In certain situations, a ‘common’ area may be needed. A common area is an area that only arms if
other specific areas are armed.
Example: A reception in a building will only need to be armed if the offices and warehouse are armed.
If the office is armed, but the warehouse isn’t, then the reception would still need to be inactive so
people would be able to leave the premises. One input can be allocated to one or more areas. In this
example the inputs located in the reception area will be in the offices and warehouse areas and have
the common attribute activated.
Area A: Office - Inputs 1, 2, 3, 4 and 8. Area B: Warehouse - Inputs 5, 6, 7 and 8.
Input 8: The detector connected to this input is going to be the input located in the Reception and is
common to Area A and Area B. Input 8 will only be active if the Area A and Area B are both armed. If
one of them is disarmed the input 8 will not be active too.
5.4.1 Input Attributes?
No Attribute Operation for both wired and wireless inputs
1 Chime When enabled the system loudspeaker(s) will ‘chime’ when an input is
triggered whilst the alarm panel is disarmed. Chime can be single –
sounding once of follow – sounding while the door is left open. NOTE: The
chime can be turned On or Off in disarmed mode by pressing [c] when all
Entry Delay inputs are closed.
2 Allow
Bypass*
Enables the input to be manually bypassed during the arming procedure or
from the user menu whilst the panel is disarmed.

PCX 46 Programming Reference
Page: 12
3 Double
Knock
If enabled, an alarm will be generated if this input is triggered twice within
the pre-programmed time window or if the input remains active for that
period. The double knock option does not work on Follow input type.
4 Combined
Input
Alarm will only be generated if 2 inputs one next to the other with
Combined Input attribute have been activated at the same time. This option
is very useful for setting up out door perimeter protection.
5 Normally
Open#
Both wired and wireless inputs are normally set to Normally Closed. This
attribute allows setting up the input as a Normally Open.
6 Mask Test The panel will not arm if the user does not activate each detector with this
attribute after starting the arming timer. This is a way to prevent arming
the system with masked or faulty detectors.
7 Non
Activity
Input
This attribute works in conjunction with the NAT (Non Activity) timer. If a
detector has not been activated in during the NAT time the NAT output if
programmed will be activated. An event will be registered in the log too.
8 Special Log
(SP)
Forces a log entry when the input is opened or closed, even when an alarm
does not result. May be selected to apply when a system is armed, when
disarmed, or always.
9 Inertia
Input
If this function is enabled, all inputs will operate as “inertia”. Please note
that only PCX-RIX8i input expanders can be used with this function. Inertia
operates by determining the gross attack and pulse count of the force. For
example:
Gross Attack = 4 m/s. Pulse Count = 3. The input will activate after sensing
3 “knocks” near the area where the shock is installed (each pulse is kept in
memory for 15 seconds).
*Only the bypassing during the arming procedure is EN50131-1 approved
#the use of this input attribute will make the system unable to comply with EN50131-1 Security
Grade 2 or 3.
NOTE: The masking is processed as 'intrusion'. The reduction of range is not supported.
5.4.2 Input Description?
2 text labels can be associated to each input:
Enter Number: Best practice is to write the Input Number (Input 1, Input 2 and so on) on this label.
This label will be shown the event log, following alarms, reported in the SMS alarms as a reference
point. There are only 7 characters available for this label.
Location: Here should be written the meaning of the input. There are 14 characters available for this
label.
Example: Input Number = Input 1; Input Name = Living Room. In case there has been tamper alarm
on input on the SMS alarms will be shown: ‘Input 2, Living Room, Tamper Alarm’. On the display will
be shown: 2-Living Room, Tamper on Input. Meaning: Tamper alarm on input 2 that is the Living
Room.
Manually Bypassing Inputs Procedure
Method 1: Whilst the system is arming, press the tkey to bypass inputs.
Method 2: Enter user menu and from the “Bypass Inputs” option bypass the inputs required.
NOTE: Only Method 1 is EN50131-1 Grade 2 or 3 compatible. The input attribute “Allow Bypass” must
be enabled on each input that you wish the user the ability to bypass.
Automatic Bypassing Inputs Procedure
Inputs may be automatically bypassed when the panel auto re-arms if this option is enabled in the
system options.

PCX 46 Programming Reference
Page: 13
5.5 Program EOL?
The end of line programming for all inputs on the PCX 46 can be selected from the below choices and is
applied to all wired inputs:
5.5.1 Choose EOL Range
[0] 1K/1K* (1K Alarm: 1K, Tamper: 1K)
[1] 4K7/2K2* (Alarm: 4K7, Tamper: 2K2)
[2] 4K7/4K7* (Alarm: 4K7, Tamper: 4K7)
[3] 4K7/2K2* Wide (Alarm: 4K7, Tamper: 2K2, Wide means (wide tolerance) that more than one
detector can be wired to an input)
An asterisk (*) indicates the single end of line value. For example, 4K7/2K2* means the 2K2 is the
single end of line value. Please note, when using a RIX8i the 1K/1K can only be used.
5.5.2 Choose EOL mode
This option is used to program single or double end of line mode of all wired inputs.
[0] Single End of Line (SEOL). [1] Double End of Line (DEOL)
5.5.3 Input Response
This option selects the time that an input must be open before the PCX 46 responds to activations.
The response time can be programmed from 100ms (0.1 seconds) to 3000ms (3 seconds).
NOTE: To comply with EN50131-1 ensure the response time is set to 400ms.
5.6 Install RIXs?
A maximum of 4 x wired input expanders or 1 x wireless input expander can be installed on the PCX 46.
Note: Wireless or wired must be chosen accordingly in the menu.
5.6.1 RIX Address
Select the address of the RIX you wish to enable (Address 0-3). NOTE: If a PCX-RIX32-WE (Enforcer
wireless expander) is installed, each address will enable 8 wireless inputs on the expander. See the
Installation Reference for more information.
5.6.2 RIX Installed
Enables the Wired or Wireless RIX that has been installed. 2 = Wireless / 1 = Wired / 0 = No
5.6.3 RIX Location
The location text is stored for reference on later maintenance visits i.e. “GROUND FLOOR”. For
information on how to use predictive text, please see page 4.
5.7 Program Outputs?
This option enables the programming of the outputs on the following Devices:
5.7.1 Endstation PGMs?
These are the outputs on control panel itself. There are 3 outputs: PGM (relay), Strobe and Bell. This
also includes the 9 ATE outputs that are enabled when a loom is connected to the board (please see
the Installation Reference manual).
5.7.2 RIX Module PGMs?
These are the outputs that are located on an input expander module if connected.
5.7.3 ROX Module PGMs?
This option enables the addition of wired ROX modules to the PCX 46.
5.7.4 Keypad PGMs?
Allows the programming of the PGM options for the output located on the wired keypads.
5.7.5 Reader PGMs?
Allows the programming of the PGM options for the outputs located on the wired readers.
5.7.6 User Outputs?
These outputs are used for creating automation control for Devices. The user can control them
remotely from the user menu on the keypad. The automated user outputs can be programmed either
latched or pulsed.
NOTE: The PGM Outputs polarity cannot be inverted. Only the ATE outputs can.

PCX 46 Programming Reference
Page: 14
No. Output Type Active Restore
0000 Not Used
0001 Fire At fire alarm activation When a valid code is entered
0002 PA Any At personal attack activation When a valid code is entered
0003 Burglary Any At burglary alarm from any area At first valid code entry
0004 Final Arm All When ALL areas are armed At code entry to disarm
0005 Open After Alarm
(Abort)
When system is silenced after ‘burglary’
alarm has been activated
After 2 minutes
0007 Tamper Any Tamper alarm in any area At code entry to silence
0008 Duress Any At a Duress alarm in any area When a valid code is entered
0009 PA Device Any At alarm on a PA input only from any
area. (This does not include the keypad
PA)
When a valid code is entered
0010 Gas At gas alarm When a valid code is entered
0011 Arm Fail Pre-set time after start of exit time, if
exit procedure is not complete
At code entry to rearm
0012 Entry Deviation When deviation from entry route occurs,
during entry time
At code entry to disarm
0013 System Ready Any When any of the inputs but the Entry
Delay and Follow are closed
If fault exists, and after final arm
0014 Bell Any After alarm in any area When alarm silenced or when siren
timer expires
0016 Strobe Any After alarm in any area When disarmed or when strobe timer
expires
0017 Bypass Rearm Any When inputs are bypassed at rearm in
any area. Turned on after 1st alarm if
active when rearmed
When system disarmed
0018 Burglary Any At Burglary alarm in any area At code entry to silence
0019 Ready All When all inputs but the Entry Delay and
Follow are closed
If fault exists, and after final arm
0020 Exit Starts All At start of exit time to arm LAST area At disarm FIRST area (i.e. no longer
fully armed)
0021 Exit Starts Any When exit time starts to arm FIRST area At code entry to disarm LAST area
0022 Final Arm Any When ANY area has been armed At code entry to disarm LAST area
0023 Strobe if Arm Fail Works similar to output 016, but also fires if the arm fail timer expires.
0024 Unable to Arm This output turns on for 5 seconds when the system is disarmed via a keyswitch
input (either pulsed or latched keyswitch)*
0025 Keyswitch Disarm Output activates when an arming procedure is completed with inputs bypassed.
0026 Arm with Bypass Active when the system is armed with an input bypassed.
0027 Pulsed Burglary Any Active when burglary alarm is triggered, but deactivates once the Pulsed
Intruder timer has expired (see Program Timers).
0028 Power Fault Active during low volts and battery faults. Restores at code entry after fault
cleared.
0031 Entry Active during any Entry time
0032 Exit Active during any Exit time
0033 Entry / Exit Active during any entry or exit time
0034 Lights When exit or entry timer starts 20 seconds after arm/disarm
procedure completed
0035 Follow Input Active when a specific input number has been activated. It allows the following
options to be programmed:
Follow Type (Follow, Timed, Latched, Code Reset);
Follow What (Input, Shunt List, Sub-Area, Area);
Follow When (Always, When Armed, When Disarmed);
Input to Follow (between 1 to 64)
0036 Shunt Fault This input activates if someone tries to shunt an input group where some of the
inputs allocated to this group are open.
0037 Restore 1 At code entry to arm. The normal state
of this input is 0v and it changes to 12v
when activated.
After 3 seconds
0038 Restore 2 Activates whenever an additional area is
armed. The normal state of this input is
0v and it changes to 12v when activated.
When disarmed
0039 PIR Latch 1 When armed (and in Walk Test) At alarm, or when disarmed
0040 PIR Latch 2 This is the inverse polarity to
PIR Latch 1
At alarm, or when disarmed

PCX 46 Programming Reference
Page: 15
0041 AC Mains Good Output showing the 230v mains supply is present
0042 PIR LED Enable This output activates during walk test
0043 Follow Test Output will activate only when tested from the Engineer menu ‘Test Outputs’ in
the ‘Engineer Tests’. This output can be used as additional facility for testing the
operation of a Bell. An output programmed to one of these configurations (43 &
44) may be used to trigger a relay to break the hold-off connection to the Bell –
or even to provide the hold-off directly.
0044 Off During Test Output is normally active and will deactivate only when tested from the Engineer
menu ‘Test Outputs’ in the ‘Engineer Tests’.
Same as 43 but opposite activation.
0048 Walk Test This output is active during walk test, and will only deactivate when all detectors
have been tested
0049 Detector Masked If any detector goes into ‘mask’
condition the output will activate
When masking fault clears
0050 Follow 24 Hour If any input programmed as ’24 Hour’
activates
When input is restored
0051 Line/GSM Fault When Telephone or GSM Line Fault is
presented
When fault clears
0052 AC Mains Fail After pre-set time without mains power On restoration of mains
0053 Battery Fault When battery disconnected or load fail
detected
At next valid code entry
0054 Low Volts When less than 11.2v is presented. When fault clears
0055 Global Fault 1
(Grade 2)
Activates if any fault occurs only when
system is armed
When all faults cleared
0056 Global Fault 2
(Grade 3)
Activates if any fault occurs at any time When all faults cleared
0057 German Relay For future development. Do Not Use.
0058 Guard Code Used When ‘guard’ code used on the system After 60 seconds
0059 Engineer Access When entering Engineer Mode When leaving Engineer Mode
0060 Follow Power Up At power up Live for 45 seconds
0063 Test UK STU Activates when a test call is sent When test completed
0064 Pre RM Service Activates 1h before the RM Service call When test completed
0065 Input Fault
(Follow NAT)
Activates when there is no activity on an
input in the end of the “NAT Non Activity
Timers” in Change Timers.
When there is activity.
0066 ATE Pin Not Used Makes the ATE pin 5V or 0V depending if ATE outputs are inverted
0067 Follow Chime Active while a Chime signal is created on the panel
0170--
0199
User Defined 01-30 The user outputs are used for user automation to control external Devices. They
can be controlled via the keypad from the used menu and can be programmed
as latched or timed (1 to 99 sec).
0202 PA A (As 0002 for Area A ) 0213 System Ready A (As 0013 for Area A )
0203 Burglary A (As 0003 for Area A ) 0214 Bell A (As 0014 for Area A)
0204 Final Arm A (As 0004 for Area A ) 0216 Strobe A (As 0016 for Area A )
0207 Tamper A (As 0007 for Area A ) 0217 Bypass At Rearm A (As 0017 for Area A )
0208 Duress A (As 0008 for Area A ) 0218 Burglary (Unconfirmed) A (As 0018 for Area A )
0209 PA Device A (As 0009 for Area A ) 0219 Ready A (As 0019 for Area A )
0210 Fire Reset A (As 0010 for Area A ) 0220 Exit Starts A (As 0020 for Area A )
Then this pattern repeats for all other areas other areas so that:
0222-0240 Area B, 0242-0260 Area C, 0262-0280 Area D, 0282-0300 Area 0,
0302-0320 Area 1, 0322-0340 Area 2, 0342-0360 Area 3
1001-1066 Active when input opened and close when input is closed
*The use of pulsed or latched keyswitch will make the system unable to comply with EN50131-1

PCX 46 Programming Reference
Page: 16
5.8 Install Keypads and Readers?
Ensure that all keypads and readers are addressed correctly before enabling them in this function.
NOTE: Care should be taken to ensure that every area that can be armed, or to which an input is
allocated, can be disarmed by at least one keypad/tag reader.
5.8.1 Device Address
Address [0] is reserved for the first LCD keypad on the bus. In the addresses from 1 to 5 is possible
to allocate external wired readers or LCD keypads.
5.8.2 Device Type
The device types that is possible to program are LCD keypads [0] or Readers [1].
5.8.3 Reader Device Type
This option will only appear when you program a Reader into the system. You can then select how you
would like the Reader to operate.
Arm/Disarm
This will make the Reader act like a normal keypad (arming/disarming the areas etc.)
Device Arms Areas: This feature programs which area(s) the reader can arm.
Device Disarms: This feature programs which area(s) the reader can disarm.
Device in Area: This feature programs in which area(s) the reader is active.
Door Name: Enter the name of the door such as Front Door.
Door Location: Enter the location of the door such as First Floor.
Arm/Disarm Sub-Area
A reader can be used to create sub-areas controlled independently from the area.
Add Inputs: Each sub-area may consist of any number of inputs, all of which must be allocated to the
same area. No input may be allocated to more than one sub-area. Entry Delay input types cannot be
allocated to a sub-area and in the sub-area the arming/disarming if the inputs is immediate without
delay timers. The sub-areas can be operated by proximity tag, or by key (or other) switch wired into
the first input on the tag reader. Notice the proximity Tags for sub-area control are programmed
through the Manager menu through the change codes options. The reader provides ‘Alarm’ and
‘Ready’ outputs dedicated to that sub-area. It also provides relevant indications, including Arm/Disarm
status, so should always be located adjacent to the controlling Key switch where this is used. Sub-
Area Arms: If this option is selected as ‘If Area Armed’ then the sub-area will always arm when the
area in which is it located is armed. If selected as ‘Never’ it will always require manual arming from
the tag. The sub-area must ALWAYS be disarmed manually. An additional option is available in the
‘SYSTEM OPTIONS’ menu, to permit a ‘Open After Alarm’ (abort) signal to be generated by silencing
an alarm at the Reader after alarm has been generated in the sub-area. Please see page 21
Action Status Notes
Disarmed Detectors within sub-areas
are inactive
‘Disarmed’ indication lit
Sub-areas input triggered No response
Attempt to arm sub-areas
with an open input
- ‘Fault’ LED flashes and
intermittent tone to indicate
‘cannot arm’
Arming with no open inputs Sub-area arms ‘Disarmed’ LED distinguishes
Sub-area input triggered Alarm generated ‘Alarm’ LED lights, alarm tone
generated
Valid code entered at a
Keypad whilst alarm in sub-
area is active
Alarm silenced by user code Sub-area remains armed
Sub-Area Control: The sub area can be controlled by Tag or Input. When an input is used to control
the sub-area a keyswitch input type should be used and connected to an external key or switch.
Sub-Area Name: Enter the name of the sub-area such as Private Office.
Sub-Area Location: Enter the location of the sub-area such as First Floor.
Assigning Tags to Sub Area Reader: To assign tags to the sub-areas, enter the master manager menu
and select ‘Change Codes’, add a new user code (tag) and when the prompt shows “Sub Area Access”,
enter the address of the reader you would like the tag to operate for the sub-areas.

PCX 46 Programming Reference
Page: 17
Access Control
Allows the reader to control doors fitted with electrical locks. On the readers there are 2 inputs that
also can be outputs. They can be connected to the lock for opening and controlling the door.
Lock Open Time: This is the time the door release is going to be active when a valid tag is presented.
Door Open Time: This is the time the door is allowed to be open before triggering an alarm.
Door Name: Enter the name of the door such as Front Door.
Door Location: Enter the location of the door such as First Floor.
NOTE: Access control falls outside the scope of EN50131-1
Disarm Only
Allows the reader to be used to disarm the system only.
Device Disarms: This feature programs which area(s) the reader can disarm.
Device in Area: This feature programs in which area(s) the reader is active.
Device Name: Enter the name of the door such as Front Door.
Device Location: Enter the location of the door such as First Floor.
Entry Control
Allows the reader to be used as arm/disarm Device and access control.
Device Arms Areas: This feature programs which area(s) the reader can arm.
Device Disarms: This feature programs which area(s) the reader can disarm.
Device in Area: This feature programs in which area(s) the reader is active.
Lock Open Time: This is the time the door release is going to be active when a valid tag is presented.
Door Open Time: This is the time the door is allowed to be open before triggering an alarm.
Door Name: Enter the name of the door such as Front Door.
Door Location: Enter the location of the door such as First Floor.
Keypad Device Type
Device Arms Areas: This feature programs which area(s) the keypad can arm.
Device Disarms: This feature programs which area(s) the keypad can disarm.
Device in Area: This feature programs in which area(s) the keypad is active.
Door Name: Enter the name of the door such as Front Door.
Door Location: Enter the location of the door such as First Floor.

PCX 46 Programming Reference
Page: 18
5.9 Program Timers?
Timers Description Options
Entry Time 1
Entry Time 2
Programmes the entry time for each area. If entry time is started
at a door programmed in multiple areas, the longest time will
apply. Entry time 1 will apply to any inputs programmed as “Entry
Delay 1” type, and Entry Time 2 will apply to any inputs
programmed as “Entry Delay 2” type. Ensure that timer is no
longer than 45 seconds in order to comply with EN50131-1.
0-255
seconds
Exit Time Programmes the exit time for each area. 0 – 255
seconds
Bell Time Cut off time for external sounder. Separate for each area. Repeat
above steps for each of the PCX 46 areas programmed on your
system.
0 – 15
minutes
Bell Delay Delay after burglary alarm before bell activation.
NOT valid within 3 minutes of final arm, or after entry time started.
If ‘Silent 1st Alarm’ selected in alarm responses, delay commences
at confirmed alarm.
0-20 minutes
Strobe Time The duration of time the strobe output remains live after the bell
time ends, ‘99’ means endless.
0-99 minutes
Number Re
arms
Number of times system re-arms after bell time ends. Re-arm
number applies to each area, and does not affect emergency
alarms. ‘9’ = ‘always re-arm’.
0 – 9
AC Fail Delay Time delay before mains failure or technical alarm signalled. ‘250’
= never alarms. System change-over to battery supply and
associated ‘alert’ indication is always immediate. Mains Fail
message on keypad not permitted until valid code entry.
0-250
minutes
Speaker
Time
Time speaker and keypad buzzers remain live after bell time ends,
‘99’ = ‘endless’.
0-99 minutes
Final Door
Delay
Time between final door input closing and system arming.
When a code is entered to arm the system the exit time will start
but the system will not arm until it sees the final exit door open
and close and duration of the final door delay.
0-255
seconds
Double
Knock
Length of filter period applied to inputs with ‘Double Knock’ input
attribute.
0 – 75
seconds
Delay Send
Entry
Delays ‘Burglary’ alarm signalling if an alarm is generated by
deviation from the entry route. Delay Send Entry must be
programmed for a minimum of 30 seconds to comply with
EN50131-1.
0-255
seconds
Line Fault
Delay
Duration of Telecom (GSM) Line Fault before ‘Line Fault’ alarm
triggered, ‘250’ endless.
0-250
seconds
Arm Fail
Time
If a system has not been armed within the entry delay time, for
example door left open the Arm Fail Time will take over and at the
expiry of this time an alarm will be created. This time should be
longer than the Entry Delay time.
0-255
seconds
Guard Code
Delay
Minimum time an alarm must have been present before a ‘Guard’
code will be accepted to disarm.
0-10 minutes
Fire Bell
Time
Cut off time for fire alarm. ‘99’ = endless. 1 – 99
minutes
Arm Fail
Warning
The “Arm Fail Warning” will overwrite the “Arm Fail Time” feature if
the “Alarm When Arm Fail” in System Options has to be set up to
NO.
Example of how this feature works: Set Arm Fail Warning longer
time than the Entry Delay Time. For example if the Entry Delay
time is set to 30sec the Arm Fail Time could be set to 1minute. If
the system is not armed after 30sec then the Entry Delay Tones
will start and the system will be disarmed at the end of the Arm
Fail Warning time. An event Arm Fail Warning Activated will be
logged in the event log too.
0 – 99
minutes

PCX 46 Programming Reference
Page: 19
NAT Day
Timer
NAT stands for Non-Activity Timer. This is used in conjunction with
the input attribute ‘Non Activity Input’, and will monitor the chosen
input for the selected number of days. At expiration of timer, and if
the input has not opened within that time, then this will be stored
in the panel log. Non Activity fault and there will be an output
activated if programmed to it. Send SMS message if “Special Log”
is on.
0-14 days
NAT Hours
Timer
NAT stands for Non-Activity Timer. This is used in conjunction with
the input attribute ‘Non Activity Input’, and will monitor the chosen
input for the selected number of hours. At expiration of timer, and
if the input has not opened within that time, then this will be stored
in the panel log. Non Activity fault and there will be an output
activated if programmed to it. Send SMS message if “Special Log”
is on.
00-23 hours
Pulsed
Burglar Any
This option sets up the duration of the pulse of an output
programmed as “Pulsed Burglary Any” activates after a burglary
alarm.
0-255
seconds
WLs
Supervision
Time
This is the time window before a supervision fault will be signalled.
For example: if the time is set for 2 hours, then any device that
doesn’t communicate with the PCX 46 within that period will cause
a supervision fault. Must be programmed to 2 hours or less for
compliance to EN 50131.
0-99 hours
WLs
Jamming
Time
This is the time window that if a wireless device had its signal
‘blocked’ a fault would display. For example, if the time is set for 30
seconds, then if a wireless device is ‘jammed’ longer than 30
seconds a fault will be displayed.
Must be set to 30 seconds or less (but not zero) for compliance to
EN 50131.
0-100
seconds
Service Time This is a timer that can be programmed in days, and will display a
message to the user warning that a service is due. An engineer
code will clear the message.
367
5.10 Change Codes?
All codes may be 4, 5, or 6 digits long and also can be assigned as proximity tags and keyfobs. 100 user
codes are available. (For Grade 3 systems please ensure that 6 digit codes are used).
NOTES: Only Duress/Guard, Master Manager and Engineer codes can be changed by the engineer. User
codes can only be changed by the Master Manager from the Master Manager menu. The Master User and
Engineer Codes cannot be deleted.
User Arm and Disarm System. Also for Access Control and Sub
Area Control functions
Programmed by
Manager only.
Manager
Default: 1234
Arm and Disarm System. Also access to Manager menu
functions
Programmed by
Manager or Engineer.
Engineer
Default: 9999
Access to all engineering functions; also arm/disarm
system for test purposes.
Programmed by
Engineer.
Duress Disarm system, generating silent ‘Duress’ signal. Programmed by
Engineer.
Guard Disarm system, but only after an alarm has been active
for a minimum time (programmable). Also arm system.
An output type is available to activate whenever this code
is used.
Programmed by
Engineer.
5.10.1 Change Duress/Guard Codes?
Choose Code Number
If a code or tag is already allocated, the display will show [******]. Press the key to clear the
code.

PCX 46 Programming Reference
Page: 20
Choose Code Number User Type
The user type can be Duress or Guard.
5.10.2 Duress Code
The Duress code can arm or disarm the system and if used a Duress communication event will be
sent. An output type is available to activate whenever this code is used (Duress type 008 - see page
32 Program Outputs).
User In Area
Choose the area the code is active in
User In AreaUser Arm Options
[0] Disarm/Arm: The code will arm and disarm the areas selected in the previous option.
[1] Disarm Only: The code will only disarm the areas selected in the previous option.
[2] Arm Only: The code will only arm the areas selected in the previous option.
[3] None: No option programmed.
User In AreaUser Arm OptionsArm Area Choice
If user code is allocated to more than one area and is the Arm Area Choice option is set to NO, the
code will automatically arm all areas it has been allocated to in the same time. If the Arm Area Choice
has been set to YES then the user will be given the ability to choose which area to arm when the
arming procedure has been activated.
User In AreaUser Arm OptionsArm Area ChoiceUser Name
Write the name of the user for this code.
5.10.3 Guard Code
This code can disarm the system, but only after an alarm has been active for a minimum time
programmable in the timers. Use of this code will generate a normal user arm/disarm event. An
output type is available to signal whenever this code is used.
User In Area
Choose the area the code is active in
User In AreaUser Arm Options
[0] Disarm/Arm: The code will arm and disarm the areas selected in the previous option.
[1] Disarm Only: The code will only disarm the areas selected in the previous option.
[2] Arm Only: The code will only arm the areas selected in the previous option.
[3] None: No option programmed.
User In AreaUser Arm OptionsArm Area Choice
If user code is allocated to more than one area and is the Arm Area Choice option is set to NO, the
code will automatically arm all areas it has been allocated to in the same time. If the Arm Area Choice
has been set to YES then the user will be given the ability to choose which area to arm when the
arming procedure has been activated.
User In AreaUser Arm OptionsArm Area ChoiceUser Name
Write the name of the user for this code.
NOTE: For both duress and guard codes is possible to program a tag too. In case tag is programmed
it has to be associated to a reader.
5.10.4 Change Master Manager Code
If a code or tag is already allocated, the display will show [******]. Press the key to clear the
code and use the numeric keys to input the new code. This option allows the engineer to change the
Master Manager code shall this been lost or forgotten.
User In Area
Choose the area the code is active in
User In AreaUser Arm Options
[0] Disarm/Arm: The code will arm and disarm the areas selected in the previous option.
[1] Disarm Only: The code will only disarm the areas selected in the previous option.
[2] Arm Only: The code will only arm the areas selected in the previous option.
[3] None: No option programmed.