Pyronix Enforcer User manual

User Manual
Wireless Alarm System
PIEZO WARNING:
This wireless alarm system contains
a 100dBA siren, please be aware of
this after activation.
EN50131-1:2006+A1:2009
EN50131-3:2009
EN50131-6:2008
EN50131-5-3:2005+A1:2008
Security Grade 2
Environmental Class II
RINS1346-4

Default Codes:
User Code: 1234
Master Manager Code: 2222

CONTENTS
CHAPTER 1: INTRODUCTION...........................................................................................4
CHAPTER 2: KEYPADS / READERS ................................................................................6
CHAPTER 3: THE KEYFOB ............................................................................................... 7
3.1 LOCKING THE KEYFOB ............................................................................................................... 7
3.2 BUTTONS................................................................................................................................... 7
3.3 QUICK SETTING ......................................................................................................................... 7
CHAPTER 4: USING PREDICTIVE TEXT ..........................................................................8
CHAPTER 5: SETTING THE ALARM (CODE/TAG) .......................................................... 9
CHAPTER 6: UNSETTING THE ALARM (CODE/TAG) ...................................................10
CHAPTER 7: UNSETTING AFTER AN ALARM .............................................................. 11
CHAPTER 8: USING A TAG READER ............................................................................ 12
CHAPTER 9: ANTI CODE / ENGINEER RESTORE ........................................................13
9.1 ANTI-CODE..............................................................................................................................13
9.2 ENGINEER RESET .................................................................................................................... 13
CHAPTER 10: INTELLIGENT SETTING ..........................................................................14
CHAPTER 11: FAULT INDICATIONS / UNABLE TO SET .............................................. 15
11.1 FAULT INDICATIONS ............................................................................................................... 15
11.2 UNABLE TO SET..................................................................................................................... 15
11.3 KEYFOB FAULT INDICATIONS.................................................................................................. 15
CHAPTER 12: ADVANCED FUNCTIONS ........................................................................ 16
12.1 CHIME FEATURE .................................................................................................................... 16
12.2 OMITTING INPUTS................................................................................................................... 16
12.3 KEYPAD HOLD UP.................................................................................................................. 16
CHAPTER 13: MASTER MANAGER MENU ....................................................................17
13.1 ENTERING THE MASTER MANAGER MENU............................................................................... 17
13.2 EXITING THE MASTER MANAGER MENU .................................................................................. 17
13.3 SET DATE AND TIME .............................................................................................................. 18
13.4 CHANGE CODES (ADDING CODES,TAGS AND KEYFOBS).......................................................... 19
13.5 REVIEW LOGS........................................................................................................................ 21
13.6 PHONEBOOK.......................................................................................................................... 21
13.7 WALK TEST ........................................................................................................................... 22
13.8 SIREN TEST ........................................................................................................................... 22
13.9 TEST CHC COMMUNICATIONS................................................................................................ 23
13.10 DIAL OUT MENU .................................................................................................................. 23
13.11 ALLOW ENGINEER MENU ..................................................................................................... 24
13.12 ENTER ANTI-CODE............................................................................................................... 24
CHAPTER 14: DISCLAIMER............................................................................................ 25
CHAPTER 15: ENGINEER CONTACTS AND TABLES...................................................26
15.1 ENGINEER INFORMATION........................................................................................................ 26
15.2 CERTIFICATION ...................................................................................................................... 26
15.3 INPUT CONTACT TABLE.......................................................................................................... 27

Page: 4
CHAPTER 1: INTRODUCTION
Two Way Wireless Security Protect Your Family and Property Without Compromise.
This wireless alarm system has been designed with your security in mind; with quick and easy
installation and minimal maintenance, this system protects your home with a multitude of
unique features.
Taking full advantage of the innovative two way wireless technology, the wireless devices on this
system are constantly communicating with each other, using High Security Wireless Encryption
Protocol.
Compared to a conventional one way wireless system, where devices can be ‘asleep’ for up to
five minutes at a time, therefore compromising your security, this alarm system ensures your
safety at your home or office at any time.
This alarm system has been engineered to be secure, reliable and easy to use. It includes the
following features:
Battery Monitoring/Saving
This wireless alarm system uses advanced technology to preserve the battery life of each
wireless device. However, the system informs you when a battery needs replacing a month in
advance before the device stops working. This key feature gives you enough time to change the
battery in the specific device. Conventional wireless alarm systems may not give you a low
battery warning signal, meaning that devices could stop working, leaving your environment
unprotected.
Intelligent Arming
This feature enables the control unit to automatically recognise when you’re at home or away.
Using this knowledge this system is able to arm itself in the correct mode without you having to
choose.
User Friendly Keyfobs
The fully two way wireless keyfob allows you to see the status of the control unit via 3 colour
LEDs:
System armed: When the system is armed a RED LED will illuminate
System disarmed: When the system is disarmed a GREEN LED will illuminate
System fault: When the system is in fault condition an AMBER LED will illuminate.
It is possible to allocate different functions to each keyfob such as arming / disarming different
areas, activating outputs, requesting system status, and activating panic alarms. Up to 32
wireless keyfobs can be added to the wireless alarm system. Each wireless keyfob has its own
user ID which can be reported to the ARC and stored into the event log of the control panel
individually. The keyfob also allows you to arm/disarm every area individually, giving you total
control of your system.
User Automation Outputs
This wireless alarm system includes user automation outputs that give you the option to operate
up to 20 devices such as gates, lights, sprinklers, etc. via your keypad or remotely via your
Keyfob, extending the use of your security system
SMS Text Notifications
This wireless alarm system will notify you via SMS text message of any incidents within your
home in real time. This can be programmed to send a notification in different situations: System
is armed or disarmed: Notification that your child has returned home from school safely. Alarm
activation: Notification that the alarm has been triggered, allowing you to monitor your home
from anywhere in the world.

Page: 5
This wireless alarm system is a level set system which may be set up in the following way:
You can choose which level set to arm, for example:
Level Set A: Full set of the house
Level Set B: Upstairs set. Downstairs unset.
Level Set C: Garage set. Rest of house unset.
Your engineer will be able to design the system according to your needs.
This alarm system can be set up to communicate to an alarm receiving centre which can monitor
all activations of your property. You can also have SMS texts sent to your phone when alarm
activation has occurred. Please ask your engineer for more information.
Default Codes:
User Code: 1234
Master Manager Code: 2222

Page: 6
CHAPTER 2: KEYPADS / READERS
There are three different devices that may be used in the process of setting/unsetting the alarm
system; these are the main keypad, the external tag reader and the internal tag reader.
Additional remote keypads may also be added, please contact your engineer for more
information.
Control Panel Keypad
a= Exit manager menu. Selects Level Set A.
b= Moves backwards to the previous menu
item. Selects Level Set B.
c= Enables chime and displays additional
information in the log. Scrolls back ‘one’ in a
sub menu. Selects Level Set C.
D= Moves forward in the log, scrolls between
options and enters the master manager menu.
Selects Level Set D.
fp = Not used.
[] = Directional buttons.
I= Selects items and enters menus.
A= Cancels items, resets the panel and
moves to next item in master manager menu.
The Internal Tag Reader
Tag Area (Where you present
your tag to set/unset)
Alert LED
Alarm LED
Tamper LED
Fault LED
Unset LED
The External Tag Reader
LEFT GREEN LED: After a valid tag is
presented, the GREEN LED will illuminate
indicating the power status.
RED LED: This can be programmed by your
engineer to illuminate when the alarm has
activated for example.

Page: 7
CHAPTER 3: THE KEYFOB
The wireless keyfob has 4 buttons that may be programmed for specific purposes (please see
Change codes on page 19 for more information).
3.1 Locking the Keyfob
All 4 buttons on the keyfob may be ‘locked’ so that any accidental presses will not affect your
alarm system (this protects the buttons from being pressed if a keyfob is next to keys etc in
someone’s pocket)
Locking the keys on the keyfob is performed by pressing
any buttons that are diagonal with one another at the
same time (LOCK & II or UNLOCK & I).
The RED LED will flash indicating that the fob has been
locked.
To unlock, press both buttons together again and the
GREEN LED will flash indicating that the keyfob is now
unlocked.
NOTE: When locked the LED status will also be disabled
3.2 Buttons
The buttons can be customised (see Change Codes, page 19) to operate as desired. The table
below gives an example of how each button may be programmed.
LOCK BUTTON = Programmed for ‘Set Area’
When pressed, the chosen area will be set (chosen in the
function ‘Change Codes’).
UNLOCK BUTTON = Programmed for ‘Unset Any Area’.
When pressed, the alarm system will unset (if set).
I BUTTON = Programmed for ‘Latch Output’
When pressed, a gate will open. When pressed again, the
gate will close.
II BUTTON = Programmed for ‘Timed Output’
When pressed, a door will unlock, after a programmed
time, the door will lock again automatically.
3.3 Quick Setting
If one of the buttons is programmed as ‘Set Area’, the alarm system can be set by the keyfob.
The keypad will then start to count down the exit time, or wait for a ‘final door’ to be closed
(depending what the exit mode is programmed as by the engineer) or the PTS button to be
pressed.
Once the alarm panel is in this ‘setting’ stage, it is possible to ‘quick set’ the system by pressing
the same button again; this will reduce the time to set to immediate. The alarm panel will
revert to the normal display with the time showing, but a beep will be heard once the system
has been set.
Please note this feature cannot be used if ‘Intelligent Arming’ is enabled.

Page: 8
CHAPTER 4: USING PREDICTIVE TEXT
The control panel incorporates predictive text, so the system will predict the word that is being
spelt.
For example, if you type ‘John’, press the 5key once and the name ‘Julia’ will appear. Press
the D
key to move the cursor over the ‘u’, and press the 6key 3 times to change it to an
‘o’. The name ‘John’ will now appear. Press the Ikey to accept.
If the word that you require does not appear in the list, just continue typing the word letter by
letter.
In addition, the 
abcD keys are used as follows:
a= make the character into a capital
b= move cursor left
c= clears cursor / adds a space
D= moves cursor right

Page: 9
CHAPTER 5: SETTING THE ALARM (CODE/TAG)
Enter your user code.
Or
Present a valid tag to the symbol
circled.
Enter the level set you wish to set, and
press the
Ikey.
‘Please wait arming wireless’ will be
displayed.
There are three different setting
methods your installer will instruct you
through which of these have been
designed into your system.
Final Door: Leave the building and
make sure the exit door is closed
properly.
Timed: Make sure you leave the
building before the timer shown on the
keypad expires.
Push to set: Press the push to set
button installed by your engineer to
arm the system.
SETTING USING A WIRELESS KEYFOB
To set via a keyfob. Press the key
The keyfob LED will start to flash
GREEN indicating that the system is
starting to set.
‘Please wait arming wireless’ will be
displayed on the keypad and the
programmed area will begin to set.
To ‘quick set’, press and hold the ARM
key a second time for 4 seconds.
Once set, the keyfob LED will
illuminate RED indicating that the
system is now set.

Page: 10
CHAPTER 6: UNSETTING THE ALARM (CODE/TAG)
Enter the building
The Entry time will start
Enter your user code
Or
Present a valid tag to the symbol
circled.
The level set that the code is assigned
to will be Unset.
Note: If ‘flexi-set’ is disabled (see
page 19) then the system will
automatically Unset that level set once
a valid user code or tag is presented.
UNSETTING USING A WIRELESS KEYFOB
PLEASE NOTE: Unsetting with a keyfob will
only be allowed if your engineer has enabled
this.
To unset via a keyfob. Press the
key.
The keyfob LED will start to flash
GREEN indicating that the system has
unset.

Page: 11
CHAPTER 7: UNSETTING AFTER AN ALARM
Enter your user code
Or
Present a valid tag to the symbol
circled.
The alarm symbol will flash indicating
there has been an alarm activation and
the keypad will display which input has
activated.
Press Athe key to reset the system
UNSETTING AFTER AN ALARM USING A WIRELESS KEYFOB
PLEASE NOTE: Unsetting with a keyfob will
only be allowed if your engineer has
enabled this.
To unset via a keyfob. Press the
key
The keyfob LED will start to flash
GREEN indicating that the system has
unset.
Resetting the system after an alarm
can only be done at the keypad.

Page: 12
CHAPTER 8: USING A TAG READER
If you have a tag reader installed, then it will be possible to set and unset the alarm system
using a tag (the same tags can also be used to set/unset via the keypad prox).
There are two types of readers that can be used with the Alarm System - the Internal Tag Reader
(used for indoors only) and the External tag reader (used for both indoors and outdoors).
Tags for the readers need to be programmed through the ‘Change Codes’ function in the Master
Manager Menu (see page 19). The internal and external readers can be both assigned to
individual level sets, this will need to be set up by your engineer.
Enabling the readers to the alarm system will be done by your engineer.
To set/unset the system using the Internal Tag Reader, present a pre-programmed tag to
the tag symbol as shown.
The system will then set depending on the type of exit mode programmed (Final door, Timed or
Push to set)
To set/unset the system using the external Tag Reader, present a pre-programmed tag to
the centre of the prox.
The system will then arm depending on the type of exit mode programmed (Final door, Timed
or Push to set)

Page: 13
CHAPTER 9: ANTI CODE / ENGINEER RESTORE
9.1 Anti-Code
Your engineer may have set up the system so that either an ‘anti code’ or engineer restore is
required in order to fully restore the system (your code will still silence the alarm, just not
restore the system).
After alarm activation has occurred, enter
your user code to silence the alarm. The
keypad will display as follows. Take note of
the number, on the screen and call your alarm
receiving centre.
Press the
Ikey
When the time is displayed, enter the number
given to you by the ARC. ‘Engineer Restore
Performed’ will be displayed.
Press the
Akey to go back to the time.
9.2 Engineer Reset
When the time is displayed, enter the
engineer number.
‘Engineer Reset Performed’ will be displayed.
Press the Akey to go back to the time.

Page: 14
CHAPTER 10: INTELLIGENT SETTING
If intelligent arm is enabled by your engineer, the system automatically recognises whether to
full arm (Level Set A), or part arm. (Level Set B). ‘Flexi’Arm (Page 19) should be disabled for this
feature to work properly.
Enter your user code
Or
Present a valid tag to the circled area
Or
Press the set button on the keyfob
The system will set in level set B (the user
code/tag/fob must be programmed for
level sets A and B).
If a final exit input is activated during the
setting procedure the system will quick set
area A.
Quick Arming...

Page: 15
CHAPTER 11: FAULT INDICATIONS / UNABLE TO SET
11.1 Fault Indications
Any faults that occur on the system will
be easily recognised by the flashing ALERT
LED.
To see what the fault is, a valid user code
needs to be entered.
Depending on how the system has been
set up by your engineer, it may be
possible to arm the system with a fault, to
do this press the Ikey.
Possible faults that may be displayed on the keypad:
Modem fault 100, Digi Fail Comm, CHC Test Fail, Line Fault 100, ATE Line Fault, ATE Fail Comm,
Device Fail ###, 485/Comms Lost, SAB Tamper, Case Tamper, Battery Fault, or Mains Fail.
The faults mentioned above may affect the overall performance of your alarm control panel, if
any of the above are displayed you should contact your engineer immediately.
11.2 Unable to Set
If ‘unable to set’ is displayed, it indicates
that an input is already active and the
area where the input is should be checked
for open windows, pets, movement etc.
If the problem cannot be solved contact
your engineer, or omit the input (page 16)
11.3 Keyfob Fault Indications
If the panel is unable to set for any reason, the keyfob status LED flashes ORANGE indicating a
fault is on the system. The fault will be shown on the keypad.

Page: 16
CHAPTER 12: ADVANCED FUNCTIONS
12.1 Chime Feature
The chime can be used for any input on
the system. This can be set up by your
engineer.
To enable the chime on the keypad, when
the time is displayed, press the
c key,
and a ‘c’ will be displayed on the right
side of the keypad display. Press the
c
key again to clear the chime feature.
12.2 Omitting Inputs
On occasion, a detector may need to be
isolated if a room is occupied.
Enter your user code
Press the I
key
Select the inputs that need to be omitted
Press the Akey
After 10 seconds the exit time continues
Note: Inputs have to be programmed as
‘omittable’ by your engineer for this
feature to operate.
12.3 Keypad Hold Up
If an emergency alarm is needed, press
and hold both the 1and
7keys.
A ‘hold up’ alarm will be generated.
Note: The Hold Up facility needs to be
enabled by your engineer (either silent or
full alarm)
2-Key HU and any duress codes
programmed on the system by your
engineer are not permitted to send a
signal to the Alarm Receiving Centre
under police regulations in England,
Wales or Northern Ireland
Please note that the keyfob can also be
programmed to support a hold up
alarm. Please discuss this with your
engineer.

Page: 17
CHAPTER 13: MASTER MANAGER MENU
The Master Manager Menu has the following functions:
Function Description
Set Date and Time Programs the date and time
Change Codes Adds/Edits/Deletes user/master codes and tags
Review Logs Displays all information of the control panel
Phone Book Adds/Edits/Deletes SMS phone numbers
Walk Test Walk tests each input
Siren Test Performs a test on all bell boxes connected
Test CHC Communications Tests a call to the SMS station
Dial Out Menu Dials to a PC for Uploading/Downloading
Allow Engineer Menu Enables or Disables engineer access
Exit Manager Mode Exits the master manager menu.
The Master Manager has access to all the options above. A ‘user code’ has access to the ‘User
Menu’ which includes the functions: ‘Change Code’, ‘Review Logs’, ‘Allow Engineer Menu’, and
‘Exit User Menu’ .
13.1 Entering the Master Manager Menu
Press the Dkey
Enter the master manager code (or
user code/tag)
Use the band Akeys to scroll
through the different functions
mentioned above.
13.2 Exiting the Master Manager Menu
Use the band Akeys to scroll
through until ‘Exit Manager Mode’ is
displayed. Press the I
key.
OR, when a main menu item is
displayed (capital letters) press the
akey.

Page: 18
13.3 Set Date and Time
Use the band Akeys to scroll to
‘Set Date & Time’. Press the Ikey.
Enter the Year
Press the Ikey
Enter the Month
Press the Ikey
Enter the Day
Press the Ikey
Enter the Hours
Press the Ikey
Enter the Minutes
Press the Ikey

Page: 19
13.4 Change Codes (Adding codes, tags and keyfobs)
The ‘Change Codes’ function allows adding, editing and deleting of user codes and the edit of
the master manager code.
Tags can also be programmed here for any user code, as well as wireless keyfobs (which are
each assigned to a user)
The control panel can have up to 80 user codes/tags (up to 32 users can be assigned to wireless
keyfobs)
Button Actions: Each wireless keyfob has 4 buttons that can be programmed for any of the
functions below:
No Action = Disables the button
Show Status = If the keyfob is learnt the LED will flicker when asked for the status.
Set Area = Sets the chosen area
Unset Any Area = Unsets any area on the system
Latch Output = Enables an output that your engineer may have programmed
Timed Output = Enables an output for a period of time that your engineer may have
programmed
Flexi-Set: Flexi-set allows you to choose which level/area to set if a user code is assigned to one
or more levels/areas. If this function is disabled, when a user code is entered, the system will
automatically set the levels/areas that the code is assigned to.
Use the band Akeys to scroll to
‘Change Codes’. Press the Ikey.
To edit user codes, press the Ikey.
Enter the user number to be edited
Press the Ikey
Enter the new code / present a tag /
press a keyfob button (this display
won’t be displayed if a keyfob is
assigned)
Once ‘asterisks’ appear, the tag or
keyfob will be assigned to this user.
Press the Ikey
Programming Wireless Keyfobs
If a keyfob is programmed, user name will be
displayed first.
Enter the user name (for help on
predictive text please see page 8)
Press the
I key.

Page: 20
Select the different buttons to program
using the band Dkeys. Press the I
key
Select the appropriate action for the
button using the band Dkeys. Press
the Ikey
Choose the type, either ‘user’ or
‘manager’ using the dkey
Press the Ikey
(This screen will not be displayed if you have
programmed a wireless keyfob)
Enter the arm modes/partitions that
the user will be assigned to.
Press the Ikey
Choose the Setting option for the user
code: Unset/Set, Unset, Set, using the
Dkey. Press the Ikey.
(This screen will not be displayed if you have
programmed a wireless keyfob)
Chooses whether Flexi-Set is to be
enabled/disabled using the Dkey.
Press the Ikey
(This screen will not be displayed if you have
programmed a wireless keyfob)
Enter the user name (for help on
predictive text please see page 8)
Press the Ikey.
To edit the Master Manager Code,
press the Ikey.
Enter the new code / present a tag /
press a keyfob button
Press the
I key
Repeat the same procedure as above.