Pyronix Matrix 6/816 User manual

Matrix 6 / 816 Getting Started
RINS700-2 Page 1
TIPRING R-1 T-117V~ + BAT - + SIREN - NC1 C1 NO1 PGM2PGM3PGM4 PGM5 PGM6 + AUX - K+ KD K- Z1 COM Z2 Z3 COM Z4 +AUX - Z5 COM Z6 Z7 COM Z8
NBUSJY
816
2 AMP AC FUSE
5 AMP BATTERY FUSE
1A AUX FUSE
1A KEYPAD FUSE
RS-232
NVM RESET
Transforme r
VV
230 /17
To mains
V
~ 230
~17V
Battery 12V
To analogue
telephone network
To o th e r
telephone equipment
RKP No1
external
ombined
sounder & strobe BELLE с
B- B+ STB BT TFBA
K+ KD K- KT KTR
4K7 4K7
4K7
4K7
Zone 1
Magnetic Contact
Zone 2
PIR
Detector
+AUX-
4К7
4K7
4 Wire Fire
Detector
Customer Support 0870 122 3360 (UK Only) Calls are charged at national rate Email: [e-mail]
Terminal Block
Link out unused zones with 4K7Ω resistors.
MATRIX 6 / 816 GETTING STARTED
Please note that the terminals on the Matrix
816 are the same as the Matrix 6
Customer Support [phone] (local rate) or [phone] Email: customer.suppor[email protected]

Matrix 6 / 816 Getting Started
Page 2 RINS700-2
Matrix 6 / 816 programming
Entering Engineer Mode
Enter () where:
() is the engineer code (default
= 9999).
Changing Engineer Code
Enter .
Enter new engineer code ().
If four- or five-digit code, press .
An acceptance tone will be heard.
Re-enter new engineer code ().
If four- or five-digit code, press .
An acceptance tone will be heard.
Setting Bell Time
Enter .
Enter time in minutes ( to , default =
20) followed by .
An acceptance tone will be heard.
Setting Entry Time
Enter .
Enter time in seconds ( to , default
= 30) followed by .
An acceptance tone will be heard.
Setting Exit Time
Enter .
Enter time in seconds ( to , default =
30) followed by .
An acceptance tone will be heard.
Programming Zones
Enter:
Arm Mode A:
 -  Zones 1 - 8
 -  Zones 9 – 16
Arm Mode B:
 -  Zones 1 - 8
 -  Zones 9 - 16
Arm Mode C:
 -  Zones 1 - 8
 -  Zones 9 – 16
Arm Mode D:
 -  Zones 1 - 8
 -  Zones 9 - 16
Enter the zone type you require as a 2-digit number:
00 = Entry Exit 07 = Patrol
01 = Access/Interior 08 = Shunt Keypad
02 = Instant 09 = Tamper
03 = Omitted (Bypass) 10 = Latch Keyswitch
04 = Fire 11 = Momentary Keyswitch
05 = Panic 12 = Unused
06 = 24 Hour
Press to accept the zone type.
Entering Account Code
Enter .
Enter the 4-digit account code followed by .
Entering Telephone Numbers
Enter:
 – Telephone 1
 – Telephone 2
 – Telephone 3
Enter the telephone number. Use the following key
presses to enter special characters:
 = *, will be displayed a 
 = #, will be displayed as 
 = 2 second pause, will be displayed as 
= Delete current number and exit function
Exiting Engineer Mode
Enter 