Pyronix Enforcer User manual

Installation Manual
EN50131-1:2006+A1:2009
EN50131-3:2009
EN50131-6:2008
EN50131-5-3:2005+A1:2008
PD6662:2010+IA:2015
Software Version >10
PIEZO WARNING
The Enforcer system contains a
100dBA siren, please be aware
of this after an activation
RINS1903-1
Enforcer
Time 10:09 c

CONTENTS PAGE
1. Introduction ............................................................................................................................3
1.1 System Overview.................................................................................................................3
2. Specification and Warranty ........................................................................................................4
2.1 Technical Specification..........................................................................................................4
3. Installation Guide .....................................................................................................................5
3.1 Mains and Earth Wiring.........................................................................................................5
3.2 Inside of the Enforcer: Rear .................................................................................................6
3.3 Inside of the Enforcer: Front ................................................................................................6
3.4 Connecting / Replacing the Control Panel Battery .....................................................................7
3.5 Important Installation Notes..................................................................................................7
3.6 RS232 Connection / Uploading and Downloading Software.........................................................8
3.7 Input / Output Board............................................................................................................9
3.8 Connecting Peripherals to the I/O Board .................................................................................9
3.9 Connecting a Wired Input Expander......................................................................................12
3.10 Connecting a Wireless Input Expander ................................................................................12
3.11 Connecting an Output Expander ......................................................................................... 13
3.12 Digi Wi-Fi (Wi-Fi Module). .................................................................................................14
3.13 Other Module Options ....................................................................................................... 14
3.14 Product Information .........................................................................................................14
3.15 Warranty ........................................................................................................................14
Default Codes:
Master Manager Code: 2222
Engineer Code: 1111

Enforcer: Installation Manual
Page: 3
1. Introduction
The Enforcer is a wireless alarm system that has been designed to enable easy installation and minimal
maintenance. The Enforcer protects the property (domestic or commercial) with a multitude of unique
features:
• Two Way Wireless Protection
• Signal Strength Indicator (SSI)
• Instant Two Way Device Control
• Pyronix High Security Wireless Protocol Encryption
• Programmable Wireless Supervision Time
• Intelligent Wireless Jamming Detection
1.1 System Overview
Areas: 4 (4 Levels/Areas)
Wireless Inputs (max): 64 (32 x onboard, 1 x EURO-ZEM32-WE )
Wired Inputs (max): 34 (2 x inputs on I/O board (Inputs 33-34) and 4 x ZEMs
(Inputs 35-66)
Total Inputs: 66
Outputs (max): 38 (1 x output module and 3 x outputs on I/O board, 4 on each ZEM
if EURO-ZEM8+ or EURO-ZEM8+PSU are used, 1 on each RKP)
User / Manager Codes: 80 (Max 32 x wireless keyfobs)
Duress / Guard Codes: 10
Code Combinations: 4294967295 (fully encrypted rolling code)
Communications: DIGI-GPRS, DIGI-LAN, DIGI-WI-FI, DIGI-GSM, DIGI-PSTN, DIGI-
PSTN/VOICE
Arming Devices (max): 4 wired keypads (EURO-LCDPZ) and/or 4 wireless keypads
(LEDRKP-WE). Internal or External Tag Readers.
Sirens: 2 Wireless Sirens or 2 Wired Sirens (in SCB mode)
Logs: 750
Remote Arm and Soak Test: 
Event Signalling to UDL: 
Memory Type: EEPROM
Compliant to EN Grade*:2
Environmental Class: II
NOTE : All wireless learning is performed in the ‘WIRELESS DEVICE CONTROL’menu, refer to the
programming manual for more details.
Compliance labelling should be removed or adjusted if non-compliant configurations are used.
Please note that technical functions for example fire, gas and flooding are not security graded as they are
outside the scope of EN50131-1 and EN50131-3.

Enforcer: Installation Manual
Page: 4
2. Specification and Warranty
2.1 Technical Specification
Enforcer Mains Inputs
European rated voltage 230V AC -15/+10%
European rated current 83mA
Capable operating voltage 90 - 264V AC
Current 222mA - 75mA
Rated Frequency 50 / 60Hz
Input Fuse Rating T 2A (cannot replace)
PSU Type A
Radio Frequency 868MHz, FM Transceiver Narrow Band
Enforcer Battery
Output instant voltage 12.71V (with no mains and battery fully charged)
Peak to peak ripple voltage 10mVpk
Battery low voltage cut off value 8.5V
Type NiMH 8 cell 2200mAh rechargeable battery
CIE current when operating on battery backup 90mA
Environment
Physical Dims 220 x 160 x 50mm
Weight 1025g
Operating Temp -10°C to +40°C
Nominal Temp -10°C to +50°C
Storage Temp -20°C to +60°C
I/O Board (If Connected)
Inputs 2 Wired (DEOL, SEOL)
Output Voltage 13.2 VDC (nominal)
Max Current for PGM Output 70mA
SAB Outputs 250mA Continuous Load
Bus Fuse F500mA 250V Bus Fuse
Aux Fuse F500mA 250V Aux Fuse
Systems Analysis: Inputs (Max 66)
On Board 32 Wireless
I/O Board 2 Wired
Input Modules 4 Wired (8 wired input each): EURO-ZEM8, EURO-ZEM8+ or
EURO-ZEM8+PSU
1 Wireless (32 wireless inputs): EURO-ZEM32-WE
Systems Analysis: Outputs (Max 40)
I/O Board 3 Wired
Keypads/Readers 3 Wired: EURO-LCDPZ, EUR-107
Input Module 16 Wired: EURO-ZEM8+
Output Module 1 Wired: EURO-OEM8R8T or EURO-OEM16R+PSU
1 Wireless: EURO-ZEM32-WE
2 x Fuses F500mA 250V
System Analysis: Additional Devices
Keypads Up to 3
Readers Up to 3
Bell Boxes 2
Wireless Arming Stations 4

Enforcer: Installation Manual
Page: 5
3. Installation Guide
NOTE 1: It is recommended that the Engineer menu is accessed prior to opening a powered Enforcer.
NOTE 2: If any new peripheral is installed (i.e. Modem, I/O board, Expander) it is recommended that the
Enforcer is powered down (mains and battery).
1. Slightly unscrew the two screws
located at the bottom.
NOTE: Do not fully unscrew at
these can be used as a 'hanger' to
the rear casing as shown in Step
3.
2. Unhinge the Enforcer from the top
and pull down to disconnect.
NOTE: Take extra care when
removing the front of the Enforcer as
modems, I/O boards etc may be
connected to the front.
3. Hang the front of the Enforcer
on the opening screws at the
bottom if required. Shown below.
3.1 Mains and Earth Wiring
It is important that the electrical earth connection is connected when connecting the 240V mains
supply to the Enforcer.
NOTE 1: Do not locate the mains cables next to internal cabling.
NOTE 2: Ensure that the Enforcer is not mounted on any metal surfaces.
NOTE 3: That the mains cables should not be internally 'looped' as shown. This may interfere with
the wireless antenna's. Where possible it is recommended that all mains cables should be installed
through the area nearest the mains terminals as shown above.
NOTE 4: If cable management is an issue, a spacer is available: ENF/SPACER-WE

Enforcer: Installation Manual
Page: 6
3.2 Inside of the Enforcer: Rear
1. Terminals for Earth and Mains Supply.
2. If a modem is required (DIGI-PSTN, DIGI-
PSTN/VOICE, DIGI-GPRS, DIGI-LAN or DIGI-WI-
FI) then this space is used to install them.
3. The transformer is situated in a housing.
4. The rear tamper adjustment screw is used if
the tamper from the front of the Enforcer isn't
sitting flush to the back plate - this may happen
if the Enforcer is installed on an uneven surface.
5. If an I/O board is installed, then this space is
used to install it.
3.3 Inside of the Enforcer: Front
1. RS232 connection for Up/downloading to
the InSite software.
2. Where the control panel battery is located.
3. The power connection for a communications
module if connected.
4. The connection for an I/O board if
connected.
5: The connection for a communication module
to be installed.
6: The power connection (+15V DC) for the
Enforcer.

Enforcer: Installation Manual
Page: 7
3.4 Connecting / Replacing the Control Panel Battery
1. Unscrew the battery
compartment
2. Connect the battery pack 3. Close the battery
compartment masking sure no
battery cable is trapped
underneath.
NOTE: The Enforcer back up battery must be replaced by the
manufacturer’s recommendation. The part code for this battery is BATT9V6/2Ah1-WE.
The battery is NiMH 8 cell 2200mAh rechargeable.
Install the batteries in the space provided and connect the battery connector to the
two pins as shown above. Reinstall the battery holder cover and dispose of the batteries in
accordance with the local regulations.
3.5 Important Installation Notes
Ensure wiring is done to the national wiring regulations in the country where the installation is
taking place. In the UK, this is BS 7671 Requirements for electrical installations; IET Wiring
Regulations (17th edition). If in doubt, consult a local qualified electrician.
Ensure that a readily accessible disconnect device incorporated in the premises installation wiring
shall be provided external to the equipment with a contact separation of at least 3,0mm and
connected as closely as possible to the supply.
Ensure that the Input and Output Board (I/O Board) used to connect wired keypads, readers,
inputs and outputs to the Enforcer, and is only connected to circuits operating at SELV voltage.
When securing external wires, ensure that means are provided in the installation to prevent the
SELV or signal circuits from coming into contact with live parts of the power supply circuit. Wires
should be fixed near their terminal blocks.
The end of stranded conductor shall not be consolidated by soft soldering at places where the
conductor is subjected to contact pressure.
On completion of wiring use tie-wraps to prevent any loose wires causing a safety hazard (material
of cables tie shall be rated at least HB or better).
Cables ties and hoses shall be separate for power supply cable and SELV wirings.
Size of protective bonding conductors: minimum section 1.5mm².

Enforcer: Installation Manual
Page: 8
3.6 RS232 Connection / Uploading and Downloading Software
The Enforcer PC software (InSite) can be downloaded from http://www.pyronix.com/pyronix-
downloads.php. To enable the Enforcer to receive upload/download commands, refer to the function
‘SET UP DOWNLOAD’ in the programming manual.
Serial Connection (RS232)
1. Open up InSite.
2. Click on Roving Dial Customer.
3. Enter the panels’ Engineer code.
4. Enter the site name.
5. (This can be found in SYSTEM OPTIONS->SYSTEM DISPLAYS in the panel on site).
6. Enter the Name.
7. The little green box which displays RS232 in the bottom left of the Insite screen should turn
yellow when connecting and when connected switch to blue.
Cloud Connection
1. Open up InSite.
2. Click on ‘Roving Dial Customer.’
3. Set ‘Dial Out Mode’ to ‘Cloud’.
4. Enter the ‘System ID’
5. Enter the panels’ ‘System Password.’
6. Enter the ‘Site Name.’ (This can be found in SYSTEM OPTIONS->SYSTEM DISPLAYS in the panel on
site).
7. Enter a Name. (Enter Customer in Database As)
8. Click dial.
9. The little green box which displays Cloud at the bottom of the Insite screen should turn yellow
when connecting and when connected switch to blue.

Enforcer: Installation Manual
Page: 9
3.7 Input / Output Board
The Input/output (I/O) board contains the RS485 terminals that are used to connect additional wired
keypads, readers, input expanders and output expanders .
Terminals:
D1-: RS485 0V
D2+: RS485 +12V
D3: RS485 'A' Bus
D4: RS485 'B' Bus
PGM1: Programmable Output
BELL: Bell output for a wired external
sounder
STRB: Strobe output for a wired external
sounder
Z33: Wired Input 33
COM: Common terminal for Z33 and Z34
+12V: +12V auxiliary supply
Z34: Wired Input 34
The maximum devices the I/O board can have on the RS485 bus are as follows:
4 x Input Expanders: EURO-ZEM8, EURO-ZEM8+, EURO-ZEM8+PSU or ZEM32-WE
1 x Output Expander: EURO-OEM8R8T or EURO-OEM16R+PSU
3 x Keypads/Readers (same bus): EURO-LCDPZ, EUR-107 or EUR-108
3.8 Connecting Peripherals to the I/O Board
Connecting Keypads (EURO-LCDPZ)
Up to 3 additional keypads can be connected to the Enforcer. These will be addressed
individually and also addressed in the Engineer function '‘Assign Keypads / Readers’.
Addressing at the keypad
Each keypad will also need to be addressed individually, press and hold the Dkey until
‘SECURITY CODE’ is displayed. Enter ‘2000’ and select the desired address (the first keypad that
is connected should be addressed as ‘1’). Press the akey to save the data and exit.

Enforcer: Installation Manual
Page: 10
Connecting Internal Tag Readers (EUR-107)
Up to 3 readers can be connected to the Enforcer. Each keypad or reader need to be addressed
as described below. These will also need assigning in the Engineer function '‘Assign Keypads /
Readers’.
Addressing at the Reader
Address 1 = SWITCH 1 ON.
Address 2 = SWITCH 2 ON.
Address 3 = SWITCH 1: ON, SWITCH 2: ON.
NOTE: If using the EUR-107 as access control/entry control please refer to the peripheral
instructions for connection details
Connecting External Tag Readers (EUR-108)
If an additional external reader is connected, this will need to be assigned in the programming,
‘Assign Keypads/ Readers’. Each reader will also need to be addressed individually via connecting
certain wires to ground.
Addressing at the Reader
Address 1: Brown, Orange to GND
Address 2: Brown, Green to GND
Address 3: Brown to GND
NOTE: If using the EUR-108 as access control/entry control please refer to the peripheral
instructions for connection details