Q-See Prosumer QT528 User manual

H.264 Dual Stream Network DVR
8 Channel CIF@240fps & D1@240fps Digital Video Recorder
USER MANUAL
Model #:
QT528
www.q-see.com
Rev 12/6/2010

1
CAUTION
Please read this user manual carefully to ensure that you can use the device correctly and
safely
The contents of this manual are subject to change without notice
This device should be used with the power supply provided. If the DVR is not going to be
used for an extended period of time unplug it.
Do not install this device near any heat sources such as radiators, heat registers, stoves or
other device that produce heat.
Do not install this device where it is exposed to water. Clean only with a dry cloth
Do not block any ventilation openings; make sure there is good ventilation around the DVR.
Do not power off the DVR while it is recording! The correct procedure is to stop recording
first by selecting the “shut-down” button at the right of the menu bar to exit, and finally to cut
off the power.
This machine is designed for indoor use. Do not expose the machine to rain or a moist
environment. If any objects or liquids get into the machine’s case, please cut off the power
supply immediately, and have qualified technicians check the machine before restarting.
Refer all servicing to qualified service personnel other then replacing hard drives or
batteries.

2
Table of Contents
1. INTRODUCTION..................................................................................................................................................4
1.1 DVR Introduction................................................................................................................................................................................................................4
1.2 Main Features....................................................................................................................................................................................................................4
2. GETTING STARTED............................................................................................................................................6
2.1 Connecting to a monitor or TV............................................................................................................................................................................................6
2.2 Installing Hard Drive...........................................................................................................................................................................................................7
2.2.1 Install DVD Writer ....................................................................................................................................................................................7
2.3 Front Panel Descriptions....................................................................................................................................................................................8
2.4 Rear Panel Layout.............................................................................................................................................................................................9
2.5 Remote Control .................................................................................................................................................................................................9
2 6 Control with Mouse ..........................................................................................................................................................................................................10
2.6.1 Connect Mouse......................................................................................................................................................................................................10
2.6.2 Use Mouse.............................................................................................................................................................................................................11
3. BASIC FUNCTION.............................................................................................................................................12
3.1 Power On/Off...................................................................................................................................................................................................................12
3.1.1 Power On...............................................................................................................................................................................................................12
3.1.2 Power Off...............................................................................................................................................................................................................12
3.2 Login................................................................................................................................................................................................................................13
3.3 Live Preview ....................................................................................................................................................................................................................13
3.3.1 Live Playback.........................................................................................................................................................................................................14
4. MAIN MENU SETUP GUIDE .............................................................................................................................15
4.1 Basic Configuration..........................................................................................................................................................................................................16
4.1.1 Setup.....................................................................................................................................................................................................................16
4.1.2 Time & Date...........................................................................................................................................................................................................17
4.1.3 DST .......................................................................................................................................................................................................................17
4.2 Live Configuration............................................................................................................................................................................................................18
4.2.1 Live........................................................................................................................................................................................................................18
4.2.2 Host Monitor...........................................................................................................................................................................................................19
4.2.3 SPOT.....................................................................................................................................................................................................................19
4.2.4 Mask......................................................................................................................................................................................................................20
4.3 Record Configuration .......................................................................................................................................................................................................21
4.3.1 Enable ...................................................................................................................................................................................................................21
4.3.2 Record stream........................................................................................................................................................................................................22
4.3.3 Time.......................................................................................................................................................................................................................23
4.3.4 Recycle Record......................................................................................................................................................................................................23
4.3.5 Stamp ....................................................................................................................................................................................................................24
4.4 Schedule Configuration....................................................................................................................................................................................................24
4.4.1 Schedule................................................................................................................................................................................................................25
4.4.2 Motion....................................................................................................................................................................................................................25
4.4.3 Sensor ...................................................................................................................................................................................................................26
4.5 Alarm Configuration..........................................................................................................................................................................................................26
4.5.1 Sensor (to setup optional external motion sensors).................................................................................................................................................27
4.5.2 Motion....................................................................................................................................................................................................................28
4.5.3 Video Loss.............................................................................................................................................................................................................30
4.5.4 OtherAlarm............................................................................................................................................................................................................31
4.5.5 Alarm Out...............................................................................................................................................................................................................31
4.6 Network Configuration......................................................................................................................................................................................................32
4.6.1 Network..................................................................................................................................................................................................................33
4.6.2 Sub Stream............................................................................................................................................................................................................34
4.6.3 Email.....................................................................................................................................................................................................34
4.6.4Other settings..........................................................................................................................................................................................................35
4.7 User Management Configuration......................................................................................................................................................................................36
4.8 P.T.Z configuration............................................................................................................................................................................................................37

3
4.9 Advanced........................................................................................................................................................................................................41
4.9.1 Reset.....................................................................................................................................................................................................................42
4.9.2 Import/Export.........................................................................................................................................................................................42
4.9.3 Block/Allow list.......................................................................................................................................................................................42
5. RECORD, SEARCH, PLAYBACK AND BACKUP ...........................................................................................43
5.1 Time Search.....................................................................................................................................................................................................................43
5.2 Event Search ...................................................................................................................................................................................................................44
5.3 File Manager....................................................................................................................................................................................................................44
6. DVR MANAGEMENT.........................................................................................................................................46
6.1 Checking System Information...........................................................................................................................................................................................46
6.1.1 System Information................................................................................................................................................................................46
6.1.2 Event Information...................................................................................................................................................................................46
6.1.1 Log Information......................................................................................................................................................................................47
6.1.2 Network information...............................................................................................................................................................................47
6.1.1 Online Information..................................................................................................................................................................................47
6.1.2 Manual Alarm.........................................................................................................................................................................................48
6.1.3 Disk Manager.........................................................................................................................................................................................48
6.1.3 Upgrade.................................................................................................................................................................................................48
6.1.4 Logoff ....................................................................................................................................................................................................48
7. REMOTE SURVEILLANCE...............................................................................................................................49
7.1 Network Access ...............................................................................................................................................................................................................49
7.2 Setting Up Remote Access...............................................................................................................................................................................................49
7.3 Port Forwarding ...............................................................................................................................................................................................................56
7.5 Using the Remote Access Software..................................................................................................................................................................................64
7.6 Remote Playback and Backup..........................................................................................................................................................................................67
7.6.1 Remote Playback...................................................................................................................................................................................................67
7.6.2 Remote Backup......................................................................................................................................................................................................70
7.7 Remote System Configuration..........................................................................................................................................................................................70
8. MOBILE SURVEILLANCE ................................................................................................................................72
8.1 Phones with Windows Mobile Pro....................................................................................................................................................................72
8.2 Phones with Symbian ......................................................................................................................................................................................74
8.3 For iPhone Mobile Clients................................................................................................................................................................................76
8.4 For Android Mobile Clients...............................................................................................................................................................................81
8.5 For Blackberry Mobile Clients ..........................................................................................................................................................................85
Installation instruction for BlackBerry Mobile phone Client ...............................................................................................................................................85
Operation method for Blackberry mobile phone client......................................................................................................................................................86
Server list ..............................................................................................................................................................87
Software configuration ........................................................................................................................................88
Information view...................................................................................................................................................88
9. PRODUCT SPECIFICATIONS...........................................................................................................................89
APPENDIX B: CALCULATE RECORDING CAPACITY (CIF)..............................................................................94

4
1. INTRODUCTION
1.1 DVR Introduction
This DVR uses high performance video processing chips and an embedded Linux system. It utilizes many advanced
technologies, such as standard H.264 with low bit rate, Dual Stream, SATA interface and VGA output. This DVR
system supports mouse controlled navigation and also can be accessed through IE browser with full remote control,
mobile viewing by cell phones, etc. This is an advanced technology DVR system which utilizes cutting edge
technology functions without compromising the stability of the system. It is ideally suited for use in such industries as
banking, telecommunication, transportation, factories, warehouses, etc.
1.2 Main Features
COMPRESSION FORMAT
Standard H.264 compression with low bit rate and high image quality
LIVE SURVEILLANCE
Supports HD VGA output
Supports channel security by hiding live display
Displays the local record state and basic information
Supports full control with USB mouse
RECORDING
Supports 2 SATA HDD up to 2TB to record for a long time periods.
Records at CIF or D1 resolution at 30FPS per camera, selectable per camera.
BACKUP
Supports backing up to USB 2.0 devices
Supports backing up to Built-in SATA DVD burner (optional)
Supports saving recorded files withAVI format to a remote computer through internet
RECORDING & PLAYBACK
Record modes: Manual, Schedule, Motion detection and Sensor alarm recording
Supports recycle after HDD is full
Resolution, frame rate and picture quality are adjustable
128MB for every video file packaging
4 audio channels available
Two record search modes: time search and event search
Support 8 screen playback simultaneously locally and 4 screen playback remotely
Supports deleting and locking the recorded files one by one
Supports remote playback in Network Client through LAN or internet

5
ALARM
1 channel alarm output and 8 channel alarm input available
Supports scheduling for motion detection and sensor alarm
Supports pre-recording and post recording
Supports linked channels recording once motion or alarm is triggered on designated channel
Supports linked PTZ preset, auto cruise and track of the corresponding channel
PTZ CONTROL
Supports multiple PTZ protocols (PelcoP, PelcoD, LILIN, MINKING, NEON, STAR, VIDO, DSCP, VISCA, and
RANGE)
Supports 128 PTZ presets and 8 auto cruise tracks
Supports remote PTZ control through internet
SECURITY
Customize user rights: log search, system setup, two way audio, file management, disk management, remote
login, live view, manual record, playback, PTZ control and remote live view
Supports 1 administrator and 15 users.
Supports event log recording and checking, events unlimited
NETWORK
Supports TCP/IP, DHCP, PPPoE, DDNS protocols
Supports IE browser to do remote viewing
Supports a maximum of 10 connections simultaneously
Supports dual stream. Network stream is adjustable independently to fit the network bandwidth and
environment.
Supports picture snap and color adjustment in remote live view
Supports remote time and event search, and channel playback with picture snap
Supports remote PTZ control with preset and auto cruise
Supports remote full menu setup, changing all the DVR parameters remotely
Supports mobile surveillance by smart phones, Win Mobile Pro, Symbian, and iPhones, iPads, Android, and
Blackberry on 3G networks
Supports CMS to manage multiple devices on the internet

6
2. GETTING STARTED
Check the unit and the accessories immediately after opening your system.
Please disconnect the power before connecting to other devices.
2.1 Connecting to a monitor or TV
The primary display on the DVR is VGA. To use with a VGAmonitor:
1. Plug the VGA cable (not included) to the VGAport on the DVR.
2. Connect the other end of the VGA cable (not included) to the monitor.
To use with a TV:
1. Plug the VGA cable (not included) to the VGAport on the DVR.
2. Connect the other end of the VGA cable (not included) to a VGA monitor.
3. Go to the login screen on the VGAmonitor and log in to the DVR.
4. Attach the RCA cable from the DVR to the RCA video in port on the TV.
5. Hold down the ESC button on the DVR for 10 seconds to transfer the video feed from the VGAmonitor to the
TV.
6. You will now be able to view the cameras and access the menus on the TV but not the VGA monitor.
NOTE: You cannot view the cameras and control the menu on a TV and VGA monitor at the same time. Please note
that you need to use a monitor that is 19” or larger.
1. Attach RCA cable to DVR
video out port using a RCA to
BNC adapter
2.
Attach the other end of the
RCA cable to a video in port
on the TV
3.
Attach one end of the VGA
cable (not
included) to the
VGA port on the DVR.
4.
Attach the other end of the
VGA cable to a VGA port on
the monitor

7
2.2 Installing Hard Drive
Notice: 1. This DVR supports two SATA hard drivers or one SATA hard drive plus one DVD-RW Writer.
2. Please calculate HDD capacity according to the recording setting. Please refer to “Appendix B Calculate
Recording Capacity”.
Step1: Unscrew and Open the top cover
Step2: Connect the power and data cables. Place the HDD onto the bottom case as below.
Fig 2.1 Connect HDD
Step3: Screw the HDD as below.
Note: For the convenience to install, please connect the power and data cables firstly, and then screw to fix.
Fig 2.2 Screw in the HDD
Note: For easier installation, please connect the power and data cables first, and then screw the HDD to
base.
2.2.1 Install DVD Writer
Notice: 1. The writer should be on the compatible devices we recommend. Please refer to “Appendix C
Compatible Devices”. Others may work, but these are the only ones we have tested.
2. This device is only for backup
Step1: Unscrew and Open the top cover
Step2: Connect the power and data cables. Place the DVD writer onto the bottom case as shown in Fig 2.3.
Step3: Screw in the DVD writer in Fig 2.4:
Fig 2.3 Connect the DVD Writer Fig 2.4 Screw in the Writer

8
2.3 Front Panel Descriptions
Fig 2.5 Front Panel
Item
Name Description
1
Power Status
Power indicator, when connection , the light is
blue
1
HDD Status
When HDD is writing and reading , the light is
blue
1
Network Status
When access to network , the light is blue
1
Backup Status
When backup files and data, the light is blue
1
Play Status
When playing video, the light is blue
1
REC Status
When recording, the light is blue
2
MENU/+
1. Enter menu in live
2. Increase the value in setup
3
P.T.Z.
Enter PTZ mode in live
4
Audio
Live or Mute Audio
5
BACKUP/-
1. Decrease the value in setup
2. Enter backup mode in live
6
Info
System Information
7
SEARCH/ZOOM
1. Enter search mode
2. ZOOM function enables at PTZ mode.
8
STOP/ESC
1. Quit play mode
2. Exit the current interface or status
9
FF
Fast Forward
10
REVSPEED
1. Reverse
2. SPEED function enables at PTZ mode
11
STOP/Pause
1. Quit play mode
2. Pause Playback
12
RECORD/FOCUS
1. Record manually
2. FOCUS function enables at PTZ mode.
13
Direction/Multi-screen
1. Change direction to select items.
2. Change screen display to 1/4/9/16 mode.
14
Enter button
Confirm selection
15
IR Sensor
For remote controller
16
USB port
To connect external USB devices like USB
flash, USB HDD for backup or update firmware.

9
2.4 Rear Panel Layout
Fig 2.5 Rear Panel
Item Name Description
1
PTZ
Connect to speed dome. Y means “+”, Z means “-”
2
K/B
Connect to PTZ keyboard
3
ALARM IN
Connect to external sensors 1-8
4
NET
Network port
5
VGA port
VGA output, connect to monitor
6
Video out
Connect to TV/monitor
7
Video in
Video input channels from 1-8
8
Audio in
4 Channels Audio input
9
POWER SWITCH
Power on/off
10
+ 5V and GND
+5 V and Grounding
11
ALARM OUT
1-ch relay output. Connect to external alarm.
12 USB port
To connect external USB devices like USB flash, USB HDD
for backup or update firmware.
13 Spot out
Connect to monitor as an AUX output channel by channel.
Only video display, no menu
14
Audio out
Audio output, connect to amplified speaker
15
POWER INPUT
DC12V
16
FAN
For cooling the device
Tab 2.1 Back Panel Ports
2.5 Remote Control
Uses two AAA size batteries, to install batteries:
Step1: Open the battery cover of the Remote Control
Step2: Insert batteries. Position the poles (+ and -) correctly
Step3: Replace the battery cover
Notice: If the remote does not work:
1. Check batteries poles
2. Check the remaining charge in the batteries
3. Check to see if IR controller sensor on DVR is blocked
If it still doesn't work, contact the Q-See customer service dept to replace the remote control.
The interface of remote controller is shown in Fig2.6 Remote Controller.

10
Fig 2.6 Remote Control
Item Name Function
1
Power Button
Stops firmware so that you can power down DVR
2 INFO Button
Get information about the DVR like firmware version, HDD
information
3
REC Button
To record manually
4
Digital Buttons
Input numbers or choose camera
5
Multi Screen Button
To choose multi screen display mode
6
SEARCH Button
To enter search mode
7
MENU Button
To enter menu
8
ENTER Button
To confirm the choice or setup
9
Direction Button
Move cursor in setup or move PTZ camera
10
+/- Button
To increase or decrease the value in setup
11
Playback Control
Button
To control playback, Fast forward/rewind/stop/single frame play
12
AUDIO Button
To enable audio output in live mode
13
Auto Dwell Button
To enter auto dwell mode, display screens in sequence
14
BACKUP Button
To enter backup mode
15 PTZ Control Button
To control PTZ camera:
Move camera/ZOOM/FOCUS/IRIS/SPEED control
Operation procedure to control multiple DVRs with same remote control
The device ID of the DVR is 0.When using remote control to control a single DVR, it’s not necessarily to reset the
device ID; when controlling multiple DVR with remote controller, please refer to below steps:
Step1: Activate remote control to control DVR: enable DVR: Point the IR sensor of the remote control at the IR
receiver that on the front panel of the DVR, press the number key 8 twice, then input device ID (Range from:
0-65535; the default device ID is 0.) with another digital number: 0-9, after that, press ENTER button to confirm.
Step2: User can check the device ID by entering into System configurationBasic configurationdevice ID.
User also can set other DVR with the same device ID. For easier operation, we don’t recommend user set the
device ID too long.
Step3: To cancel a device ID: Point the IR sensor of the remote control at the IR receiver that is on the front panel,
press the number key 8 twice, then input the device ID that needs to be cancelled, press ENTER button to
confirm. After that, the DVR will not be controlled by remote control.
2 6 Control with Mouse
2.6.1 Connect Mouse
DVR supports USB mouse through the port on the rear panel, please refer to Fig 2.4 Number 5.
Notice: If mouse is not detected or doesn't work, check below steps:
1. Make sure the mouse plugs in the USB mouse port on the back of the DVR, not the front panel port.
2. Try a different mouse

11
2.6.2 Use Mouse
In Live:
Double-click left button on one camera to be full screen display. Double-click again to return to the previous screen
display.
Click right button to show the control bar at the bottom of the screen as Fig 4-1 main menu toolbar
Click right mouse again to hide the control bar.
In Setup:
Click left button to enter. Click right button to cancel setup, or return to the previous screen.
If you want to input values, move cursor to the blank and click. An input window will appear as shown in Fig2.6. It
supports numbers, letters and symbols.
Fig 2.6 Numbers and Letters Input Window
Users can change some values by the wheel, such as time. Move cursor onto the value, and roll the wheel when the
value blinks.
Also supports mouse drag. I.e. Set motion detection area: click customized, hold left button and drag to set motion
detection area. Set schedule: hold left button and drag to set schedule time
In playback:
Click left button to choose the options. Click right button to return to live view.
In backup:
Click left button to choose the options. Click right button to return to previous picture.
In PTZ control:
Click left button to choose the buttons to control the PTZ. Click right button to return to live view.
Notice: Mouse is the default tool for all the operations below unless otherwise noted.

12
3. BASIC FUNCTION
3.1 Power On/Off
Before you power on the unit, please make sure all the connections are good.
3.1.1 Power On
Step 1: Connect the power supply; switch on the power button near the power port on the rear panel
Step 2: The firmware will be loaded, and the power indicator will display blue
Step 3: At start up, a WIZZARD dialogue box will pop-up (refer to picture below) displaying time zone and time setup
information.
After the device powers on, if there is no menu or only displays live image, user can hold down ESC button to switch.
Notice: this unit can only display menu on VGA monitor or BNC monitor one at a time. If there is live image
display without menu display, please check to see if other monitoring device has menu display first, or hold
down ESC key to wait for login dialog box to appear.
3.1.2 Power Off
User can power off the device by using remote control, keyboard or mouse.
By Remote Control:
Step 1: Press Power button, the Shut down window will appear, click OK, the unit will power off after firmware is shut
down.
Step 2: Disconnect the power.
By Keyboard and Mouse:
Step 1: Enter into Menu, then select “System Shut Down” icon, the Shut down window will appear
Step 2: Click OK, the unit will power off after firmware is shut down.
Step 3: Disconnect the power.

13
3.2 Login
User can login and logout of the DVR system. User cannot do any other operations except changing the multi-screen
display once logout.Admin has full control over DVR.
Fig 3-1 Login
Notice: the default user name and password is “admin” and 123456”
For information on how to change password, add or delete users please refer to Section 4.7 User
management configuration.
3.3 Live Preview
Fig 3-2 Live Preview Interface
The explanation of symbols in the live preview interface:
Symbol
Meaning
Symbol
Meaning
Green
Manual record or time
recording
Red
Alarm
recording
Yellow
Motion detection recording
Figure icon
Motion event

14
3.3.1 Live Playback
Click the Play button to playback the record. Refer to Figure3-3. User can operate by clicking the buttons on the
screen.
Fig 3-3 Live Playback

15
4. MAIN MENU SETUP GUIDE
Click right mouse or press ESC button on the front panel, the control bar will display on the bottom of the screen,
refer to Fig 4-1:
Fig 4-1 Main Menu Toolbar
Click icon beside the screen display mode, a channel select dialog will appear as below:
Take 8-channel DVR for example: user can tick off 8 channels form 1-ch to 8-ch at random to display the
live pictures. Then click button to confirm the setting.
Click icon, user can zoom in the live and playback images. When single image display, user can
select zoom in area by dragging mouse.
Click the Menu button, the interface will pop-up as shown in Fig 4-2; press MENU button on the front
panel or remote control will also display the main interface.
Fig 4-2 Main Menu

16
4.1 Basic Configuration
Basic configuration includes three sub menus: system, date& time and DST.
4.1.1 Setup
Step1: Enter into Setup configurationbasic configurationsetup; refer to Fig 4-3:
Fig 4-3 Basic Configuration
Step2: In this interface user can setup the device name, device ID, video format, max network users, VGAresolution
and language. The explanations for each display are shown below:
Device name: the name of the device. It will display on the client end or CMS and help user to recognize the
device remotely.
Video format: two modes: PAL and NTSC. User can select the video format according to that of camera, in
USA and Canada we use NTSC cameras.
Password Check: if you enable this option, user needs to input user name and password to do corresponding
operations in system configuration.
Show time: display time in live view.
Show wizard: check this item, an opening wizard will display with time zone and time setup information
Max network users: set the maximum number of network connections
VGA resolution: the resolution of live display interface, options are: VGA800*600, VGA1024*768,
VGA1280*1024 and CVBS
Note: Switching between VGA and CVBS will change the menu output mode, please connect to
relevant monitor, VGA for VGA monitor, CVBS for TV or monitor that is connected using BNC adapter.
Language: setup the menu language.
Note: after changing the language and video output, the device needs to restart.
SETUP

17
4.1.2 Time & Date
Step 1: Enter into system configurationbasic configurationtime & date; refer to Fig 4-4:
Fig 4-4 Basic Configuration-Time & Date
Step 2: Set the date format, time format, time zone in this interface; Checkmark “sync time with NTP server” to
refresh NTP server date; user also can adjust system date manually
Step 3: Click “default” button to restore default settings; click “apply” button to save the settings; click “exit” button to
exit current interface.
4.1.3 DST
Step1: Enter into system configurationbasic configurationDST; refer to Fig 4-5:
Fig 4-5 Basic Configuration-DST
Step 2: In this interface, you can enable daylight saving time, time offset, mode, start & end month/week/date, etc.
Step 3: Click “default” button to restore default settings; click “apply” button to save the settings; click “exit” button to
exit current interface.

18
4.2 Live Configuration
Live configuration includes four submenus: live, host monitor, SPOT and mask.
4.2.1 Live
In this interface, user can setup camera names, adjust colors: brightness, hue, saturation and contrast.
Step 1: Enter into system configurationlive configurationlive; refer to Fig 4-6:
Fig 4-6 Live ConfigurationLive
Step 2: Checkmark camera name; click “setting” button, a window will pop-up shown as Fig 4-7:
Fig 4-7 Live-Color Adjustment
Step 3: In this interface, user can adjust brightness, hue, saturation and contrast in live view; click “default” button to
restore default settings, click “OK” button to save the settings.
Step 4: User can setup all channels with same parameters, checkmark “all”, then do relevant setup.
Step 5: Click “default” button to restore default settings; click “apply” button to save the settings; click “exit” button to
exit current interface.

19
4.2.2 Host Monitor
Step 1: Enter into system configurationlive configurationhost monitor; refer to Fig 4-8:
Fig 4-8 Live Configuration-Host Monitor
Step 2: Select split mode: 1×1, 2×2, 2×3, 3×3, and channel
Step 3: Dwell time: the time interval for a certain picture display before switching to next picture display
Step 4: Select the split mode, then setup current picture group. Click button to setup the previous channel groups
of pictures, click button to set latter channel groups of pictures.
Step 5: Click “default” button to restore default settings; click “apply” button to save the settings; click “exit” button to
exit current interface.
NOTE: If you have dual monitors Host monitor needs to be main monitor.
4.2.3 SPOT
Step 1: Enter into system configurationlive configurationSPOT; refer to Fig 4-9:
Fig 4-9 Live Configuration-SPOT
Step 2: Select split mode: 1×1 and channel
Step 3: Dwell time: the time interval for a certain picture display before switching to the next picture display.
Step 4: Select the split mode, then setup current picture group. Click button to setup the previous channel groups
of pictures, click button to set the latter channel groups of pictures.
Step 5: Click “default” button to restore default setting; click “apply” button to save the setting; click “exit” button to
exit current interface.
To activate this setting, go to the main camera screen and click on the Dwell icon (Fig 4-1). This will make the camera
rotate based on the setting in Main Monitor.