Qazqa 89522 User manual

P.1
Item:89522
www.qazqa.com

1. Warning symbols
Read the instructions
Caution
Lamp
2. General Safety Instructions
Read this instruction manual thoroughly before using the appliance and save it for future reference and if
necessary pass the instruction manual on to a third party.
WARNING: When using electrical appliance, basic safety precautions should always be followed to reduce
the risk of fire, electrical shock and personal injury.
P.2

1) General
Before carrying out any work on the fan, disconnect it from the electrical supply!
Check if the electrical specifications of this appliance are compatible with your installation. The
suppler accepts no responsibility for any physical injury or material damage resulting from
incorrect use or installation of this fan. If you have the slightest doubt, please contact electrician。
Unauthorized use and technical modifications to the appliance can lead to danger to life and health.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure
that they do not play with the appliance
Children should be supervised to ensure that they do not play with the appliance.
This appliance is for indoor use only.
Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
Never install the appliance in a moist or wet room.
Be careful when working near the rotating blades. The fan should be installed at least a height of 2.3m
Before pushing the reversible slide switch, it is necessary to stop the action of the blades by turning off the fan
Don’t place your arm or other object in the path of the blades, when the fan is operating.
Always maintain the minimum distance between the lamp and any inflammable material (curtains, wall
etc), as indicated on the pictogram
Means for all poles disconnection having a contact separation that provide full disconnection under over voltage
category III conditions must be incorporated in the fixed wiring in accordance with national wiring rules.
Power supply wire from ceiling needs 1.5 sq mm wire
Warning: Before obtaining access to terminals, all supply circuits must be disconnected.
P.3

2. Electrical safety
The appliance should be installed by authorized electrician only acc. to national wiring rules.
3. Specific Safety Rules
The fan is to be installed so that the blades are more than 2.3 m above the floor
4. Environmental protection
CAUTION!
Electrical products must not be thrown out with domestic waste. They must be taken to a communal
collecting point for environmentally friendly disposal in accordance with local regulations. Contact your
local authorities or stockist for advice on recycling. The packaging material is recyclable. Dispose of
the packaging in an environmentally friendly manner and make it available for the recyclable material
collection-service.
5. Appliance specifications
TECHNICAL CHARACTERISTICS
Rated voltage
230 V
Rated frequency
50 Hz
Rated wattage
50 W
Bulb rating
E14 1x60W Max.
Ambient operating temperature
25 °C
Protection class
I
IP number
IPX0
Protective shields
N/A
P.4

.
6. The ceiling fan (element)
PARTS DESCRIPTION
1. MOUNTING PLATE
2. J HOOK (FOR TEMPORARY HANG UP THE FAN
WHEN WIRING CONNECTION)
3. SCREWS
4. SCREWS
5. HANGER BALL
6. UPPER CANOPY
7. DOWNROD
8. CROSS PIN
9. SCREWS
10. COTTER PIN
11. DOWNROD YOKE
12. MOTOR
13. BLADE HOLDERS SCREW
14. BLADE
15. BLADE HOLDER
16. SCREW
17. LIGHT PLATE COVER
18. LIGHT PLATE
19. LAMP HOLDER
20. BULB (Not provided)
21.GLOBE
P.5

7. Installation of the ceiling fan
1. Install the mounting
plate by screw (Fig.1)
2. Insert downrod over
upper canopy (Fig 2)
3. Then, insert the cross
pin over yoke and
Cotter pin(Fig3)
4. Connect the wire as the
fig show (Fig 4)
1
2
3
P.6
4

5. Make sure the wiring correct, if you
are not sure, pls consult qualified
electrician (Fig.5)
Black +Brown wire “L”
Blue wire “N”
Green & yellow wire
6. Hang up the fan and assembly
the mounting plate with the
motor set by 4 side screws
(Fig 6)
7. Assembly the blades to blade
holders (Fig7)
8. Install the holder on motor by
screws (Fig 8)
9. Install the light bulb (not provided)
(Fig 9)
10. Install the glass
(Fig 10)
5
6
7
8
9
10
P.7

If the fan or light kit is PARTIALLY pre-assembled, you can skip the assembly procedures to next step
11
11. Now, the fan is
completed (Fig 11)
P.8

8. How to use
- One pull chain switch is for light control, another one for speed control
- The speed can be selected by pressing the speed chain
HI-1 pull, MED –2pull, LOW—3 pull, OFF----4pull
- Light on off can be controlled by pressing the light chain
ON-1 pull, OFF–2pull
- Direction switch on the fan ‘s switch box(SUMMER and WINTER switch)
- Down for summer make the air movement directly from ceiling
- Up for winter, to circulate the warm air generated by heater to floor
9. Remote Control (remote control adaptable, but this model does not included)
This ceiling fan can be installed with remote control, but make sure you know how to install the device in safe way or
consult licensed electrician
Warranty may be affected if you install the improper remote control or install it in improper way
10.Disconnect from mains before maintenance or cleaning.
Do not use a wet sponge to clean the appliance.
1. Before conducting any cleaning or maintenance work, disconnect the lamp from the electrical supply and wait until it
cools down
2. No abrasive products, solvents, detergent or any other liquid may be used to clean the fan or lamp
3. Be sure the power is off when you clean the fan
4. Don’t clean the motor, switch house and other electric parts of the fan with water in order to avoid short circuit
st nd rd th
st nd
P.9

11.Trouble shooting
TROUBLE
PROBABLE CAUSES
SUGGESTED REMEDY
1. Fan will not start
A/ Fuse or circuit breaker blown.
B/ Loose power line connections
to the fan.
C/ Speed controller not in correct
position.
A/ Check main and branch circuit
fuses or circuit breakers.
B/ Check line wire connections to fan
C/ Check speed controller’s position.
2. Fan sound noisy
A/ Top canopy touching ceiling.
B/ Loose fan blade screws.
C/ Ceiling fan not secured against
ceiling.
D/ Incorrect speed controller.
A/ Lower Canopy from ceiling to
ensure minimum 3 mm clearance.
B/ Re-tighten all screws on fan blades
but never over-tighten.
C/ Re-tighten all screws in the
hanging bracket or plate.
D/ Change the controller to the one
supplied.
3. Mechanical Noise
A/ Allow at least for 8 hours
settling-in period.
4. Fan Wobbles
A/ Fan blades are not horizontal to
ceiling.
B/ Blade screws are loose.
A/ Measure from ceiling to tip of
blades, then rotate fan so all blades
are checked for equal height from
ceiling (not adjustments may be made
by slight pressure up or down on
blade holders). Make sure all screws
are securely fastened.
DYNAMIC BLADE BALANCE KIT
YARDSTICK
MEASURING
POINT
P.10

PREFACE
Your ceiling fan may sometimes have wobble problem when operate due to irregularity in blades or the blade holder. Also, improper
assembly in the mounting system may cause some additional problem also bearing crooked. The following procedure to remedy such
problem is strongly recommended by us from our past experience in handling the wobble problem.
Dynamic blade balancing kit for ceiling fans
1. Make sure that all blade are firmly screwed into the blade holder
2. Make sure that all blades are firmly secured the flywheel and check pitch of blade holders all must be the same
3. By looking up the fan from below, check and be certain that none of the blade holders are bent so that none of the blade is out
of position. A correction can be made by very gently bending the blade holder back into position
4. By the simple use of a household yardstick blade tracking can be checked, out the yardstick up against the ceiling vertically and
even with the outside leading edge of a blade. Note the distance of the edges of the blade to t he ceiling; carefully turn the blade
slowly by hand to check the remaining blades. If blade is not in alignment, the blade holder may be gently bent up or down
to be in line with the other blades
If by following all the steps and the wobble problem is not solved, a dynamic balancing need to be done by the use of the balancing
kit. Follow the procedure listed below:
Turn the fan on and adjust the speed control (usually high speed) setting to the speed, which creates to greatest wobble.
Turn the fan off; select on blade place the balance clip on it. Halfway between the blade holder and the blade up on the
rear edge of the blade.
Turn the fan on, watch to see of the wobble is improved or worse. Then, turn the fan off again and move the clip to
another blade and test again. Repeat this process with all blades and then note that blade which is the most improved.
Move the clip back to the blade, which showed the most improvement. Move the clip inward and outward on this
blade and operate t he fan to find the position where the clip gives the most improvement
Next remove the clip and install a balancing weight to the top of the blade along the centerline near the point where
the clip was positioned.
Caution: stay clear of the blades if the clip for any reason is not secured, injury could result
12. Others
Have your product repaired by a qualified person
This electric product is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons
using original spare parts; otherwise this may result in considerable danger to the user.
Please contact the store which you bought the product for after sale services if question
P.11