Qazqa Fanattic 98355 User manual

Thisitemcontains
UnchangeableLED
700 LM
12 W
3000 K
>80 CRI
20000 H
15000ON/OFF
Fanattic Fan
98355/98356/98357
English and Dutch
1x12W LED

P
1
EN
EN
1. Warning symbols
Read the instructions
Caution
Lamp
2. General Safety Instructions
R
ead this instruction manual thoroughly before using the appliance and save it for future reference and if
necessary pass the instruction manual on to a third party.
WARNING: W hen using electrical appliance, basic safety precautions should always be followed to
reduce the risk of fire, electrical shock and personal injury.

P
2
EN
1) General
Before carrying out any work on the fan, disconnect it from the electrical supply!
Check if the electrical specifications of this appliance are compatible with your installation. The suppler accepts
no responsibility for any physical injury or material damage resulting from incorrect use or installation of this
fan. If you have the slightest doubt, please contact electrician .
Unauthorized use and technical modifications to the appliance can lead to danger to life and health.
T
his appliance can be used by children aged from 8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision
Children should be supervised to ensure that they do not play with the appliance.
This appliance is for indoor use only.
M
eans for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
Never install the appliance in a moist or wet room.
Be careful when working near the rotating blades. The fan should be installed at least a height of 2.3m
B
efore pushing the reversible slide switch, it is necessary to stop the action of the blades by turning off the fan
Don ’ t place your arm or other object in the path of the blades, when the fan is operating.
Always maintain the minimum distance between the lamp and any inflammable material (curtains,
wall etc), as indicated on the pictogram
Means for all poles disconnection having a contact separation that provide full disconnection under over
voltage category III conditions must be incorporated in the fixed wiring in accordance with national wiring rules.
P
ower supply wire from ceiling needs 1.5 sq mm wireWarning: Before obtaining access to terminals, all supply circuits must be disconnected.

P
3
EN
TECHNICAL
TECHNICAL
TECHNICAL
TECHNICAL CHARACTERISTICS
CHARACTERISTICS
CHARACTERISTICS
CHARACTERISTICS
Rated voltage
2 2 0-240 V
Rated frequency 50 Hz
Rated wattage 60 W
Bulb rating 1x12W . LED
Ambient operating temperature
25 ° C
Protection class I
IP number IPX0
Protective shields N/A
5. Appliance specifications
Electrical products must not be thrown out with domestic waste. They must be taken to a communalcollecting point for environmentally friendly disposal in accordance with local regulations. Contact yourlocal authorities or stockist for advice on recycling. The packaging material is recyclable. Dispose ofthe packaging in an environmentally friendly manner and make it available for the recyclable materialcollection-service.
CAUTION!
4. Environmental protection
3. Specific Safety RulesT
he fan is to be installed so that the blades are more than 2 . 3 m above the floor
2. Electrical safetyThe appliance should be installed by authorized electrician only acc. to national wiring rules.

P
4
6.The ceiling fan (element)
PARTS DESCRIPTION
1.Mounting bracket
2.Screws
3.Screws
4. Hanger ball
5. Upper canopy
6. Down rod
7. Cross pin
8. Cotter pin
9.Down rod Yoke
E N
10. Screw
11. Motor
12. Blade holder screw
13. Blade
14. Blade holder
15. Screws
16. Light kit fixing bracket
17. Led light plate
18.Transmitter
19.Remote control receiver

P
5
7. I nstallation of the celing fan
1. Install the mountingbracket by screw(Fig.1)
2. Assembly the blades to bladesholder by screw .(Fig.2)
3. Loose the screw from motor.(Fig.3)
EN
4. Install the blade on the motor byS crews. (Fig.4)

P
6
5. C arefully insert the fan into the
M ounting bracket. Rotate the fan until
the notch of the hanger ball engages the
the pin of the mounting bracket. Then,
firmly fix the screws. (Fig 5)
6. To connect the power supply from EN
the celing and fan. (Fig 6)
7. I nsert the remote control receiver on
the mounting bracket. (Fig 7)
8. Connect the transmitter and remote
C ontrol recevier wire by male and female
P lug. (Fig 8)

P
7
9. Stick the lens on the canopy. (Fig 9)

P
8
E
E
E
E N
N
N
N
8. How to use-
D
irection switch on the fan ‘ s switch box (SUMMER and WINTER switch)
-D
own for summer make the air movement directly from ceiling
-U
p for winter, to circulate the warm air generated by heater to floor
9. Remote ControlT
his ceiling fan can be installed with remote control, but make sure you know how to install the device in safe way or
consult licensed electricianW
arranty may be affected if you install the improper remote control or install it in improper way
10.Disconnect from mains before maintenance or cleaning.D
o not use a wet sponge to clean the appliance.
1.
B
efore conducting any cleaning or maintenance work, disconnect the lamp from the electrical supply and wait until it
cools down
2.
N
o abrasive products, solvents, detergent or any other liquid may be used to clean the fan or lamp
3.
B
e sure the power is off when you clean the fan
4.
D
on ’ t clean the motor, switch house and other electric parts of the fan with water in order to avoid short circuit

P 9
11.Trouble shooting
EN
TROUBLE
PROBABLE CAUSES SUGGESTED REMEDY
1. Fan will not start
A/ Fuse or circuit breaker blown.
B/ Loose power line connections
to the fan.
C/ Speed controller not in correct
position.
A/ Check main and branch circuit
fuses or circuit breakers.
B/ Check line wire connections to fan
C/ Check speed controller's position.
2. Fan sound noisy
A/ Top canopy touching ceiling.
B/ Loose fan blade screws.
C/ Ceiling fan not secured against
Ceiling.
D/ Incorrect speed controller.
A/ Lower Canopy from ceiling to
ensure minimum 3 mm clearance.
B/ Re-tighten all screws on fan blades
C/ Re-tighten all screws in the
hanging bracket or plate.
D/ Change the controller to the one
supplied.
3. Mechanical Noise
A/ Allow at least for 8 hours
Settling-in period.
4. Fan Wobbles
A/ Fan blades are not horizontal to
Ceiling.
B/ Blade screws are loose .
A/ Measure from ceiling to tip of
blades,then rotate fan so all blades
are checked for equal height from
ceiling (not adjustments may be made
by slight pressure up or down on
blade holders.) Make sure all screws
Are securely fastened.

P 10
EN
PREFACE
Your ceiling fan may sometimes have wobble problem when operate due to irregularity in blades or the blade holder. Also, improper assembly in the mounting system
may cause some additional problem also bearing crooked. The following procedure to remedy such problem is strongly recommended by us from our past experience in
handling the wobble problem.
Dynamic blade balancing kit for ceiling fans
1. Make sure that all blade are firmly screwed into the blade holder
2. Make sure that all blades are firmly secured the flywheel and check pitch of blade holders all must be the same
3. By looking up the fan from below, check and be certain that none of the blade holders are bent so that none of the blade is out of position. A correction can be
made by very gently bending the blade holder back into position
4. By the simple use of a household yardstick blade tracking can be checked, out the yardstick up against the ceiling vertically and even with th e outside leading
edge of a blade. Note the distance of the edges of the blade to t he ceiling; carefully turn the blade slowly by hand to check the remaining blades. If blade is not
in alignment, the blade holder may be gently bent up or down to be in line with the other blades
If by following all the steps and the wobble problem is not solved, a dynamic balancing need to be done by the use of the balancing kit. Follow the procedure listed
below:
Turn the fan on and adjust the speed control (usually high speed) setting to the speed, which creates to greatest wobble.
Turn the fan off; select on blade place the balance clip on it. Halfway between the blade holder and the blade up on the rear edge of the blade.
Turn the fan on, watch to see of the wobble is improved or worse. Then, turn the fan off again and move the clip to another blade and test again. Repeat this
process with all blades and then note that blade which is the most improved.
Move the clip back to the blade, which showed the most improvement. Move the clip inward and outward on this blade and operate t he fan to find the position
where the clip gives the most improvement
Next remove the clip and install a balancing weight to the top of the blade along the centerline near the point where the clip was positioned.
Caution: stay clear of the blades if the clip for any reason is not secured, injury could result
12. Others
Have your product repaired by a qualified person
This electric product is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise
this may result in considerable danger to the user. This appliance can be used by children aged from 8 years and above if they have been given supervision or
instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children
unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
Please contact the store which you bought the product for after sale services if question
question
question
question

P
11
T
his appliance can be used by children aged from 8 years and above if they have if they have been given supervision or instruction concerning use
Of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children
Unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
Appliances can be used by persons with reduced physical,sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or intruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
EN
lnformation
lnformation
lnformation
lnformation requirements
requirements
requirements
requirements regarding
regarding
regarding
regarding the
the
the
the eco-design
eco-design
eco-design
eco-design
Description Symbol Value
M aximum fan flow rate
F
117.42
Fan power iuput
P54
S ervice value
SV 2.17
( )/W
Standby power consumption
PSB
0.00
Seasonal electricity consumption
Q
17.28
KW/n/a
Fan sound power level
LWA
48.90
Maximum air velocity
C
1.61
m/seg
Measurement standard for service
Regulation N
º
206/2012IEC 60789:1986
EN 50564:2011
EN 60704-2-7:1998
EN60704-1:2010[Shall not appear all of these ones, but the same as the ones which are detaild inThe ERP test report]

P
12
EN

EN
P13

HANDLEIDING
Plafondventilator Fanattic
98355/98356/98357
P. 1

Lees de instructies
Waarschuwing
Lamp/Lichtbron
Waarschuwings symbolen
Algemene veiligheidsinstructies
Lees dit instructieboekje zorgvuldig door voor gebruik. Bewaar de kassabon/factuur samen met
deze handleiding als toekomstige referentie/garantie en geef dit boekje door wanneer nodig
aan de derde partij.
WAARSCHUWING: Bij gebruik het van elektrische producten, neem de voorzorgsmaatregelen
in acht om kans op vuur, elektrische schokken en persoonlijke verwondingen te voorkomen.
P. 2

1) Algemeen
WAARSCHUWING: Om het risico van brand en elektrische schokken te voorkomen,
schakel je de stroomtoevoer naar de ventilator uit in de hoofdzekeringkast of de hoofd-
schakelkast voor je begint met het installeren van de ventilator of voor je de ventilator
onderhoudt of accessoires installeert.
Controleer voordat je de ventilator aansluit of het voltage van de ventilator overeenkomt met
de netspanning van je woning. De verkoper is niet aansprakelijk voor lichamelijke of
materiële schade die te wijten is aan het niet naleven van deze handleiding of wanneer
blijkt dat de ventilator niet naar behoren is gemonteerd. Als je enige onzekerheden hebt
neem dan contact op met een elektricien.
Gebruik uitsluitend de door de fabrikant geleverde of aanbevolen onderdelen. Maak geen
aanpassingen aan de ventilator. Onverantwoord gebruik en technische modificaties aan de
ventilator kunnen leiden tot lichamelijk letsel of schade aan de ventilator.
De installatiehoogte tussen vloer en bladen moet ten minste 2,30 meter zijn.
Zorg ervoor dat je voor de ventilator een plaats hebt gekozen die voldoende vrije ruimte
biedt zodat de bladen ongehinderd kunnen draaien. Controleer of er geen obstakels in het
draaigebied zijn.
De - / + polen moeten los van elkaar worden bevestigd om overspanning op de bedrading
te voorkomen. Zorg ervoor dat alle elektrische aansluitingen voldoen aan de plaatselijke
wetgeving en voorschriften inzake elektrische installaties.
Deze ventilator mag alleen worden gebruikt met minimaal 1,5 mm²installatiedraad.
Kinderen onder de 8 jaar en personen met een lichamelijke of verstandelijke beperking die
niet in staat zijn het apparaat te hanteren zoals in de gebruiksaanwijzing is beschreven,
mogen dit apparaat niet gebruiken.
P. 3

Laat geen verpakkings onderdelen (plastic zak, doos en piepschuim) binnen het bereik van
kinderen liggen.
Om de kans op lichamelijk letsel of schade aan de ventilator of andere voorwerpen te
vermijden, dien je voorzichtig te zijn bij het werken aan of in de buurt van de ventilator en
bij het schoonmaken ervan. Schoonmaken en onderhoud van de ventilator mag niet
worden gedaan door kinderen zonder toezicht.
Gebruik geen water of agressieve reinigingsmiddelen voor het schoonmaken van de ventila-
tor en de bladen. Een droge stofdoek of licht bevochtigde doek volstaat meestal voor het
schoonmaken.
Gebruik deze ventilator niet in dezelfde ruimte en op hetzelfde ogenblik met een gasvuur of
vuur met andere brand stof, tenzij het rookkanaal onder deze omstandigheden door een
bevoegd persoon is getest.
Deze ventilator is niet geschikt voor gebruik in de badkamer of in andere ruimtes waarin de
ventilator in contact met water kan komen.
Gebruik de knop voor het omkeren van de draairichting niet voordat de ventilator volledig
tot stilstand is gekomen.
Steek nooit iets tussen de bladen van de ventilator terwijl ze draaien
Vanwege Europese veiligheidsvoorschriften mag de ventilator, indien deze vlak tegen het
plafond wordt geïnstalleerd niet opnieuw worden geïnstalleerd met een stang. Als dit wordt
geprobeerd, kan dit ernstig letsel veroorzaken.
Gebruik geen dimmer om de snelheid van de ventilator te regelen.
Na het voltooien van de installatie controleer je of alle aansluitingen absoluut veilig en
stevig zijn gemonteerd.
P. 4

P. 5
2. Elektriciteits veiligheid
De installatie van de ventilator moet worden uitgevoerd door iemand die over de beno-
digde kennis beschikt of door een erkend elektricien volgens de nationale bedrading regels.
3. Specifieke veiligheidsregels
Zorg dat de ventilator minimaal 2.30 meter boven de vloer geïnstraleerd word.
4. Milieubescherming
5. Ventilator Specificaties
WAARSCHUWING!
Gooi elektrische producten niet bij het huisvuil. Neem contact op met je
gemeente of fabrikant voor advies over het recyclen van de ventilator. Ook
het verpakkingsmateriaal is recyclebaar. Lever dit product en het verpakking-
smateriaal in bij het daarvoor bestemde inzamelpunt in je gemeente.
Voltage / Spannigs toevoer
Frequentie
Wattage
Lichtbron
Omgevingstemperatuur
Bescherm Klasse
IP waarde
Bescherm Velden
220/240V
50HZ
60W
1x 12W LED module
25 °C
I
IP20
N/A
TECHNISCHE GEGEVENS

P. 6
ONDERDELEN BESCHRIJVING
1. Ophangbeugel
2. Schroeven
3. Schroeven
4 . Bevestigings module
5. Plafondplaat
6. Stalen stang
7. Splitpen
8. Dwarspen
9. Stang bevestiging
10. Schroef
11. Moter
12. Bladhouder schroeven
13. Ventilator blad
14 . Blad houder
15. Schroeven
16. Bevestigingsbeugel voor LED module
17. LED module
18. Afstandsbediening
19. Afstandsbediening ontvanger
6. Onderdelen plafondventilator