Qazqa 91342 User manual

P.1
INSTRUCTION MANUAL
Breeze Fan 48 Chrome/Breeze Fan 48 White
91342/91343

1. Warning symbols
R ead the instructions
C aution
L amp
2. General Safety Instructions
R ead this instruction manual thoroughly before using the appliance and save it for future reference and if
necessary pass the instruction manual on to a third party.
WARNING: W hen using electrical appliance, basic safety precautions should always be followed to
reduce the risk of fire, electrical shock and personal injury.
P.2

1
)
General
P.3
 B
efore carrying ou
t
any work on the fan, disconnec
t
it from the electrical supply!
 C
heck if the electrical specifications of this appliance are compatible with your installation. The suppler
accepts no responsibility for any physical injur
y
or material damage resulting from incorrect use or installation
of this fan. If you have the slightest doubt, please contact electrician.
 U
nauthorized use and technical modifications to the appliance can lead to danger to life and health.
 T
his appliance can be used b
y
children aged from 8 years and above and persons with reduced physical,
sensor
y
or mental capabilities or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe wa
y
and understand the hazards involved. Children shall
no
t
play with the appliance. Cleaning and user maintenance shall no
t
be made b
y
children withou
t
supervision
 C
hildren should be supervised to ensure tha
t
they do no
t
play with the appliance.
 T
hisapplianceisforindooruseonly.
 M
eans for disconnection mus
t
be incorporated in the fixed wiring in accordance with the wiring rules.
 N
ever install the appliance in a mois
t
or wet room.
 B
e careful when working near the rotating blades. The fan should be installed a
t
leas
t
aheigh
t
of 2.3m
 B
efore pushing the reversible slide switch, i
t
is necessary to stop the action of the blades b
y
turning off the fan
 D
on’
t
place your arm or other objec
t
in the path of the blades, when the fan is operating.
 A
lways maintain the minimum distance between the lamp and any inflammable material
(curtains, wall etc), as indicated on the pictogram
 M
eans for all poles disconnection having a contact separation tha
t
provide full disconnection under over
voltage categor
y
III conditions mus
t
be incorporated in the fixed wiring in accordance with national wiring
rules.
 P
ower suppl
y
wire from ceiling needs 1.5 sq mm wire
W
arning: Before obtaining access to terminals, all suppl
y
circuits mus
t
be disconnected.

2
.
El
ectrica
l
sa
f
et
y
T
he appliance should be installed by authorized electrician only acc. to national wiring rules.
3. S
p
ecific Safet
y
Rules
T
he fan is to be installed so that the blades are more than 2.3 m above the floor
4
.
E
nvironmenta
l
p
rotection
CAUTION!
E
lectrical
p
roducts must no
t
be thrown out with domestic waste. The
y
must be taken to a communal
collectin
g
p
oin
t
for environmentall
y
friendl
y
dis
p
osal in accordance with local re
g
ulations. Contac
t
y
our
local authorities or stockis
t
for advice on rec
y
clin
g
.The
p
acka
g
in
g
material is rec
y
clable. Dis
p
ose of
the
p
acka
g
in
g
in an environmentall
y
friendl
y
manner and make it available for the rec
y
clable material
collection-service.
5. A
pp
liance s
p
ecifications
TECHNICAL CHARACTERISTICS
Rated volta
g
e220-240
V
Rated frequency 50 Hz
Rated wattage 60 W
Bulb rating E14 2x40W Max.
Ambien
t
o
p
eratin
g
tem
p
erature 25
°C
Protection class I
IP number IPX0
Protective shields N/A
P.4

.
6. The ceiling fan (element)
PARTS DESCRIPTION
1. MOUNTING BRACKET
2. SCREWS
3. SCREWS
4. TERMINAL BLOCK
5. REMOTE CONTROL
6. MALE AND FEMALE PLUS
7. HANGER BALL
8. UPPER CANOPY
9. DOWNROD
10. SCREW
11. UPPER CANOPYCOVER
12. SCREWS
13. BLADE HOLDERS SCREW
14. BLADE
15. LIGHT PLATE
16. LAMP HOLDER
17. BULB (No
t
p
rovided)
18.GLASS
P.5

7. Installation of the ceilin
g
fan
1. Install the mounting Bracket b
y
screw
(Fig.1)
2. Inser
t
downrod over upper canop
y
(Fig 2 3)
3. Then, insert the cross pin over yoke and
Cotter pin(Fig4)
4. Remove the 2 screws from the rectangular
cover on the motor housing and remove the
plate,inser
t
the blades through the slots
around the motor. Align the blade with the e
three holes,and secure the three screws
through the opening. Tighten all blade screw
evenly and get the rectangular cove secured
b
y
screws (Fig 5)
5. Connect the wire as the fig show (Fig 6)
6. Insert the remote control into the mounting
bracke
t
(fig 7)
P.6

7. Make sure the wirin
g
correct, if
y
ou
are not sure,
p
ls consult
q
ualified
electrician
(
Fi
g
.8
)
Black +Brown wire “L”
Blue wire “N”
Green &
y
ellow wire
8. Theconnectthefemaleandmale
p
lus#1to#1#2to#2
(
Fi
g
9
)
9. Fix the screw to the u
pp
er cano
py
(
Fi
g
10
)
10. Inset the len into the receiver and
connect the supply wire of the
receiver to the terminal(Fig 11)
12. Install the li
g
htin
g
bulb
(
no
t
p
rovided
)
(
Fi
g
12
)
13. Install the glass (Fig 13)
P.7

If the fan or light kit is PARTIALLY pre-assembled, you can skip the assembly procedures to next step
14
14. Now, the fan is
completed (Fig 14)
P.8

8
.
H
ow to use
-
O
ne pull chain switch is for light control, another one for speed control
-
T
he speed can be selected by pressing the speed key on remote control
-
L
ight on off can be controlled by remote
-
D
irection switch on the fan ‘s switch box(SUMMER and WINTER switch)
-
D
own for summer make the air movement directly from ceiling
-
U
p for winter, to circulate the warm air generated by heater to floor
9. Remote Control
T
his ceiling fan can be installed with remote control, but make sure you know how to install the device in safe way or
consult licensed electrician
W
arranty may be affected if
y
ou install the improper remote control or install it in improper way
10.Disconnect from mains before maintenance or cleanin
g
.
D
o not use a wet sponge to clean the appliance.
1.
B
efore conducting any cleaning or maintenance work, disconnect the lamp from the electrical supply and wait until it
cools down
2.
N
o abrasive products, solvents, detergent or any other liquid may be used to clean the fan or lamp
3.
B
esurethepowerisoffwhen
y
ou clean the fan
4.
D
on’t clean the motor, switch house and other electric parts of the fan with water in order to avoid short circuit
P.9

11.Trouble shootin
g
TROUBLE PROBABLE CAUSES SUGGESTED REMEDY
1. Fan will not start A/ Fuse or circuit breaker blown.
B/ Loose
p
ower line connections
to the fan.
C/ S
p
eed controller not in correct
p
osition.
A/ Check main and branch circuit
fuses or circuit breakers.
B/ Check line wire connections to fan
C/ Check s
p
eed controller’s
p
osition.
2. Fan sound nois
y
A/ To
p
cano
py
touchin
g
ceilin
g
.
B/ Loose fan blade screws.
C/ Ceilin
g
fan not secured a
g
ainst
ceilin
g
.
D/ Incorrect s
p
eed controller.
A/ Lower Cano
py
from ceilin
g
to
ensure minimum 3 mm clearance.
B/ Re-ti
g
hten all screws on fan blades
but never over-ti
g
hten.
C/ Re-ti
g
hten all screws in the
han
g
in
g
bracket or
p
late.
D/ Chan
g
e the controller to the one
su
pp
lied.
3. Mechanical Noise A/ Allow at least for 8 hours
settlin
g
-in
p
eriod.
4. Fan Wobbles A/ Fan blades are not horizontal to
ceilin
g
.
B/ Blade screws are loose.
A/ Measure from ceilin
g
to ti
p
of
blades, then rotate fan so all blades
are checked for e
q
ual hei
g
ht from
ceilin
g
(not ad
j
ustments ma
y
be made
b
y
sli
g
ht
p
ressure u
p
or down on
blade holders). Make sure all screws
are securel
y
fastened.
DYNAMIC BLADE BALANCE KIT
YARDSTICK
MEASURING
POINT
P.10

P.11
PREFACE
Y
our ceiling fan may sometimes have wobble problem when operate due to irregularity in blades or the blade holder. Also, improper assembly in the mounting system
may cause some additional problem also bearing crooked. The following procedure to remedy such problem is strongly recommended by us from our past experience in
handling the wobble problem.
D
ynamic blade balancing kit for ceiling fans
1.
M
ake sure that all blade are firmly screwed into the blade holder
2.
M
ake sure that all blades are firmly secured the flywheel and check pitch of blade holders all must be the same
3.
B
y looking up the fan from below, check and be certain that none of the blade holders are bent so that none of the blade is out of position. A correction can be
made by very gently bending the blade holder back into position
4.
B
y the simple use of a household yardstick blade tracking can be checked, out the yardstick up against the ceiling vertically and even with the outside leading edge
of a blade. Note the distance of the edges of the blade to t he ceiling; carefully turn the blade slowly by hand to check the remaining blades. If blade is notin
alignment, the blade holder may be gently bent up or down to be in line with the other blades
I
f by following all the steps and the wobble problem is not solved, a dynamic balancing need to be done by the use of the balancing kit. Follow the procedure listed below:

T
urn the fan on and adjust the speed control (usually high speed) setting to the speed, which creates to greatest wobble.

T
urn the fan off; select on blade place the balance clip on it. Halfway between the blade holder and the blade up on the rear edge of the blade.

T
urn the fan on, watch to see of the wobble is improved or worse. Then, turn the fan off again and move the clip to another blade and test again. Repeat this process
with all blades and then note that blade which is the most improved.

M
ove the clip back to the blade, which showed the most improvement. Move the clip inward and outward on this blade and operate t he fan to find the position
where the clip gives the most improvement

N
ext remove the clip and install a balancing weight to the top of the blade along the centerline near the point where the clip was positioned.
C
aution: stay clear of the blades if the clip for any reason is not secured, injury could result
12
.
O
t
h
ers
H
ave your product repaired by a qualified person
T
his electric product is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise
this may result in considerable danger to the user. This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction
concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are
older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
P
lease contact the store which you bought the product for after sale services if question

T his appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of
the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children
unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
A ppliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall no
t
p
la
y
with the a
pp
liance.