Qazqa Gaiola 102712 User manual

P.1
Gaiola Fan Black 102712 5×E27MAX 40WINSTRUCTION MANUAL

1. Warning symbolsRead the instructionsCaution Lamp2. General Safety InstructionsRead this instruction manual thoroughly before using the appliance and save it for future reference and if necessary pass the instruction manual on to a third party.WARNING: When using electrical appliance, basic safety precautions should always be followed to reduce the risk of fire, electrical shock and personal injury.1)GeneralBefore carrying out any work on the fan, disconnect it from the electrical supply!Check if the electrical specifications of this appliance are compatible with your installation. The supplier accepts no responsibility for any physical injury or material damage resulting from incorrect use or installation of this fan.If you have the slightest doubt, please contact electrician.Unauthorized use and technical modifications to the appliance can lead to danger to life and health.This appliance can be used by children aged from 8 years and above and persons with reduced physical,sensory or mental capabilities or lack of experience and knowledge if they have been given supervision orinstruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervisionChildren should be supervised to ensure that they do not play with the appliance.This appliance is for indoor use only.Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.Never install the appliance in a moist or wet room.Be careful when working near the rotating blades. The fan should be installed at least a height of 2.3mBefore pushing the reversible slide switch, it is necessary to stop the action of the blades by turning off the fanDon’t place your arm or other object in the path of the blades, when the fan is operating.Always maintain the minimum distance between the lamp and any inflammable material(curtains, wall etc), as indicated on the pictogramMeans for all poles disconnection having a contact separation that provide full disconnection under over voltage category III conditions must be incorporated in the fixed wiring in accordance with national wiring rules.Power supply wire from ceiling needs 1.5 sq mm wireRegarding the method of the cable connection , how to assembly and the bulb type reference of a luminaire, thanks to refer to the section “INSTALLATION”Warning: Before obtaining access to terminals, all supply circuits must be disconnected.“5. Appliance specification”.Warning: Before obtaining access to terminals, all supply circuits must be disconnected.P.2

2) Electrical safetyThe appliance should be installed by authorized electrician only acc. to national wiring rules.3) Specific Safety RulesThe fan is to be installed so that the blades are more than 2.3 m above the floor4) Environmental protection CAUTION!Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting point for environmentally friendly disposal in accordance with local regulations. Contact your local authorities or stockist for advice on recycling. The packaging material is recyclable. Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection-service.5) Appliance specifications
TECHNICAL CHARACTERISTICS
Rated voltage
220-240 V
Rated frequency
50 Hz
Rated wattage
38 W
Bulb rating
5xE27. MAX 40W
Ambient operating temperature
25 °C
Protection class
I
IP number
IPX0
Protective shields
N/A
6) The ceiling fan (element)PARTS DESCRIPTION1.Safesteelwire2.Jhook(Fortemporaryhangupthefanwhen wiringconnection)3.Mountingbracket4.Nuts5.Receiver6.Remote7.Hangerball8.Downrod9.Uppercanopy10.Screws11.Yokecover12.Crosspin13.Cotterpin14.Screws15.Blades16.MotorHousing17.Motor18.Lightplate19.Nuts20.Lightkit21.Shade22.Screws23.NutP.3

2
7) Installation of the ceiling fan1.nsert down rod over upper canopy, then insert the crosspin over yoke & Cotter pin and fasten the screws which fix the down rod(Fig 1)2.Install the mounting plate by screws (Fig.2)3.Loose the screw from motor.(Fig 3)4.Install the blade on the motor by Screws.(Fig.4)5.Make sure the fan is disconnected from the electrical supply and carefully insert the fan into the Mounting bracket. Rotate the fan until the notch of the hanger ball engages the pin of the mounting bracket. Then, firmly fix the screws.(Fig5)6.Assembly the LED light plate to the light kit fixing bracket by the screws and connect the LED light kit by male & female plug. Insert the remote control receiver on the mounting bracket. Connect the motor wires, LED light wires and receiver’s power wires to the receiver by male & female plug.Also, connect the ground wire by male & female plug.Then connect the power supply with the fan.(Fig6)7.Assembly the shade to the light plate and assembly the upper canopy to the mounting bracket. Both rotateclockwise when assembling.(Fig 7)If the fan or light kit is PARTIALLY pre-assembled, you can skip the assembly procedures to next stepP.5

8) How to use-Direction switch on the fan ‘s remote.(FORWARD and REVERSE switch)-Down for summer make the air movement directly from ceiling.-UP for winter, to circulate the warm air generated by heater to floor.9) Remote Control InstructionThis ceiling fan can be installed with remote control, but make sure you know how to install the device in safe way orconsult licensed electricianWarranty may be affected if you install the improper remote control or install it in improper way.(1) WIRING SCHEMATIC DIAGRAM FOR RECEIVERAdopt RF wireless digit emission technique, biunique controlled , coincident code rate is less than one millionth.(Emitter and receiver must be sent back to factory for maintenance if damaged.)Receiver can be controlled by any angles of the emitter in prescriptive space, unrestricted by direction. With the memory function, the controller can save the status( light and direction ) while the supply power OFF and resume to the original after reload the power supply.(2) FUNCTION INSTRUCTION OF EMITTER(3) KINDLY REMINDERS:1. Learning code matching mode is used between emitter and receiver. Turn "ON” the supply power within 30 seconds and press the emitter's "FAN ON/OFF" button for 5 seconds, it can load normally after hearing a long sound “bee”， which means learning successfully and it can works normally. (PS: Learning mode is not accepted after turn "ON” the supply power for 30 seconds)2. When the emitter cannot control the receiver, please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.3. When the emitter cannot control the receiver, please check is there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled product with the same frequency will disturb each other.4. Low voltage of battery will affect the sensitivity of the emitter and the signal reception accordingly (the indicated light will flash out its warning when the battery get low voltage), must replace if the battery is getting low voltage.5. Please take out the battery from the emitter when leaving unused for long time.6. The maximum load of lighting see the aboveHPOWER PARAMETER LIST"PS： please connect the ground wire correctly,otherwise it may cause the light micro-light or flash7. When installing the fan,the fan ceiling cover don't press the antenna(or other wire),it is easy to breakdownthe wire and short-circuited. P.6

10) Disconnect from mains before maintenance or cleaning.Do not use a wet sponge to clean the appliance.1.Before conducting any cleaning or maintenance work, disconnect the lamp from the electrical supply and wait until it cools down2.No abrasive products, solvents, detergent or any other liquid may be used to clean the fan or lamp3.Be sure the power is off when you clean the fan4.Don’t clean the motor, switch house and other electric parts of the fan with water in order to avoid short circuit11) Trouble shooting
TROUBLE
PROBABLE CAUSES
SUGGESTED REMEDY
1. Fan will not start
A/ Fuse or circuit breaker blown. B/ Loose power line connections to the fan.C/ Speed controller not in correct position.
A/ Check main and branch circuit fuses or circuit breakers.B/ Check line wire connections to fan C/ Check speed controller’s position.
2. Fan sound noisy
A/ Top canopy touching ceiling. B/ Loose fan blade screws.C/ Ceiling fan not secured against ceiling.D/ Incorrect speed controller.
A/ Lower Canopy from ceiling to ensure minimum 3 mm clearance.B/ Re-tighten all screws on fan blades but never over-tighten.C/ Re-tighten all screws in the hanging bracket or plate.D/ Change the controller to the one supplied.
3. Mechanical Noise
A/ Allow at least for 8 hours settling-in period.
4. Fan Wobbles
A/ Fan blades are not horizontal to ceiling.B/ Blade screws are loose.
A/ Measure from ceiling to tip of blades, then rotate fan so all blades are checked for equal height from ceiling (not adjustments may be made by slight pressure up or down on blade holders). Make sure all screws are securely fastened.
DYNAMIC BLADE BALANCE KITYARDSTICKMEASURING POINTP.7

Information requirements regarding the eco-design
Description
Symbol
Value
Unit
Maximum fan flow rate
F
64.16
m3/min
Fan power input
P
43.50
W
Service value
SV
1.47
(m3/min)/W
Standby power consumption
PSB
0.0
W
Seasonal electricity consumption
Q
13.92
kWh/a
Fan sound power level
LWA
43.50
dB(A)
Maximum air velocity
c
1.42
m/seg
Regulation Nº 206/2012IEC 60879:1986EN 50564:2011
Measurement standard for service
EN 60704-2-7:1998EN 60704-1:2010[Shall not appear all of these ones, but the same as the ones which aredetailed in the ERP test report]
PREFACEYour ceiling fan may sometimes have wobble problem when operate due to irregularity in blades or the blade holder. Also, improper assembly in the mounting systemmay cause some additional problem also bearing crooked. The following procedure to remedy such problem is strongly recommended by us from our past experience inhandling the wobble problem.Dynamic blade balancing kit for ceiling fans1.Make sure that all blade are firmly screwed into the blade holder2.Make sure that all blades are firmly secured the flywheel and check pitch of blade holders all must be the same3.By looking up the fan from below, check and be certain that none of the blade holders are bent so that none of the blade is out of position. A correction can bemade by very gently bending the blade holder back into position4.By the simple use of a household yardstick blade tracking can be checked, out the yardstick up against the ceiling vertically and even with the outside leading edgeof a blade. Note the distance of the edges of the blade to t he ceiling; carefully turn the blade slowly by hand to check the remaining blades. If blade is not inalignment, the blade holder may be gently bent up or down to be in line with the other bladesIf by following all the steps and the wobble problem is not solved, a dynamic balancing need to be done by the use of the balancing kit. Followthe procedure listed below:Turn the fan on and adjust the speed control (usually high speed) setting to the speed, which creates to greatest wobble.Turn the fan off; select on blade place the balance clip on it. Halfway between the blade holder and the blade up on the rear edge of the blade.Turn the fan on, watch to see of the wobble is improved or worse. Then, turn the fan off again and move the clip to another blade and test again. Repeat this processwith all blades and then note that blade which is the most improved.Move the clip back to the blade, which showed the most improvement. Move the clip inward and outward on this blade and operate t he fan to find the positionwhere the clip gives the most improvementNext remove the clip and install a balancing weight to the top of the blade along the centerline near the point where the clip was positioned.Caution: stay clear of the blades if the clip for any reason is not secured, injury could result12) OthersHave your product repaired by a qualified personThis electric product is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwisethis may result in considerable danger to the user. This appliance can be used by children aged from 8 years and above if they have been given supervision or instructionconcerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.Please contact the store which you bought the product for after sale services if questionThis appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.Children shall not play with the appliance.Please contact the store which you bought the product for after sale services if questionP.8

P.9