Quadivator PB60 06 User manual

QUADIVATOR INC.
Power Brush PB60 06
Assembly/Operators/Parts Manual
English Language Version 06
Printed: September 2006
Part #: 89754A
1000 6th Ave. NE
Portage La Prairie, MB
Canada, R1N 3C5
www.quadivator.com
READ & SAVE THIS MANUAL

QUADIVATOR WARRANTY POLICY
The warranty for the Quadivator Product is a limited warranty.
The manufacturer’s warranty to the original customer is - the product is free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the
original purchaser.
We will repair or replace, at our discretion, parts found to be defective due to materials and
workmanship.
The warranty is subject to the following limitations and exclusions:
1. Engine Warranty
- all engines utilized on our products have a separate warranty
extended to them by the engine manufacturer. Any engine service difficulty is the
responsibility of the engine manufacturer and in no way is Quadivator Inc. or its agents
responsible for the engine warranty. The Briggs & Stratton Engine Service Hot Line is 1-
800-233-3723.
2. Commercial Use -
the warranty period for any product used for commercial or rental use
is limited to ninety (90) days from the date of original purchase.
3. Limitations -
the warranty applies only to products which have been properly assembled,
adjusted and operated in accordance with the instructions contained within this manual.
The warranty does not apply to any product of Quadivator Inc. that has been subject to
alteration, misuse, abuse, improper assembly or installation, shipping damage or normal
wear of the product.
4. Exclusions -
excluded from this warranty are normal wear, normal adjustments and
normal maintenance.
In the event you have a claim under this warranty, you must return the product to an
authorized service dealer. All transportation charges, damage or loss incurred during
transportation of parts submitted for replacement or repair under this warranty shall be
borne by the purchaser. Should you have any questions concerning this warranty, please
contact us toll-free at 866 770-2169 or on our web-site at www. quadivator.com . The
model, serial numbers, date of purchase and the name of the authorized Quadivator dealer
from whom you purchased the Quadivator Product will be needed before any warranty
claim can be processed.
This warranty does not apply to any incidental or consequential damages and any implied
warranties are limited to the same time periods stated for all expressed warranties. Some
provinces and states do not allow the limitation of consequential damages or limitations on
how long an implied warranty may last, so the above limitations may not apply to you. This
warranty gives you specific legal rights and you may have other rights, which vary from
province to province or state to state.
This is a limited warranty as defined by the Magnuson-Moss Act of 1975.

Quad Power Brush
Operators Manual – Version 06
i
FOREWORD
Congratulations on the purchase of your new Quadivator PB60 Power Brush. To obtain the best use
of your Power Brush, read this manual carefully. It will help you become familiar with the operation
and maintenance of the Quadivator PB60. It is Quadivator Policy to use all research, design and
manufacturing improvements to improve our Power Brush. At the time of printing, this may result in
some of the minor parts in the manual becoming outdated.
Quadivator will have the most up to date parts and service information – call 866 770-2169 for service
information and parts orders!
Contact Information
Quadivator Inc. E-mail: [email protected]
1000 – 6
th
Ave NE Website: www.quadivator.com
Portage la Prairie, MB Tel. [phone]
Canada, R1N 3B5 Fax. [phone]

This symbol, the industry’s “Safety Alert Symbol”, is used throughout this manual and on labels on the
device itself to warn the possibility of personal injury.
Read these instructions carefully.
It is essential that you read the instructions and safety regulations before you attempt to assemble or
use this brush.
Indicates an imminent hazardous situation, which if
not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate
injury.
DANGER
SAFETY FIRST
WARNING
CAUTION

Quad Power Brush
Operators Manual – Version 06
ii
Table of Contents
1. Safety First ………………………………….……………………………. i
2. Pre-delivery Checklist…………………………………………………… iii
3. Owners Registration & Delivery Checklist……….………………….. iv
4. Safe Operation …………………………………..….……………………. 1
5. Setup & Operation ……………….………………….……..……………. 2
Brush Mounting ………………………………………………………….. 2
Angle Adjustment………………………………………………………… 2
Gage Wheels………………………………………………………………. 3
General Operation………………………………………………………… 3
Storage……………………………………………………………………… 3
Maintenance………………………………………………………………...3
6. Replacement Parts…………………………………….…………………. 5
7. Warranty Registration………………………………….………………… 17
Serial Number Location

Quad Power Brush
Operators Manual – Version 06
ii
i


PRE- DELIVERY CHECKLIST
Check off all items as they are found satisfactory or after adjustments are made:
All safety shields and guards are securely in place!
All decals are in place and readable!
All fasteners are securely tight
Start the Quadivator Power Brush and allow it to run for 5 – 10 minutes, check for
excessive operation or unusual noise.
The Quadivator Power Brush has been tested and to the best of my knowledge, is ready to
be delivered to the customer!
Date Pre-delivered –
Signature –

To help prevent personal injury from
thrown objects, never walk or stand in
the front area of the brush during run-in
or operation!
CAUTION

Quad Power Brush
Operators Manual – Version 06
iv
OWNER’S REGISTRATION











 !

"


DELIVERY Checklist
#$%&#&#'%
(#)%*#$%
(##$%#&+$&#,%#
(##$%#"$$
(##$%#"$-$
 $.

#$%/#&'0

($%.&#)%%$
'#$&#1$
2#$%#+1%$%'#$%#
%




Quad Power Brush
Operators Manual – Version 06
1
SAFE OPERATION
1. GENERAL OPERATION
.1 Read the operating and service instruction manual
carefully.
.2 Become thoroughly familiar with the controls and the
proper use of the equipment. Know how to stop the unit
and disengage the controls quickly.
.3 Allow only responsible adults, who are familiar with
the instructions, to operate this machine. Never allow
children to operate the equipment.
.4 Be sure the area is clear of bystanders, children and
pets before operating. Stop machine if anyone or
anything enters the area.
.5 NEVER CARRY PASSENGERS while sweeping with
the PB60





.6 Thoroughly inspect the area where the equipment is
to be used and remove all foreign objects.
.7 Disengage clutch on ATV and shift ATV into neutral
before starting the engine (motor). Refer to the safety
section in the ATV operators manual
.8 Never attempt to make adjustments while the engine
(motor) is running
.9 Always wear safety glasses or eye shields: during
operation, while performing an adjustment or repairs; to
protect eyes from foreign objects that may be thrown
from the machine.
.10 Maintain or replace safety and instruction labels, as
necessary. Never tamper with safety devices and check
their proper operation regularly.
2. GENERAL DEVICE OPERATION
.1 Do not put hands or feet near or under rotating parts.
.2 Exercise extreme caution when operating on or
crossing gravel drives, walks or roads. Stay alert for
hidden hazards and traffic.
.3 After striking a foreign object; stop the engine
(motor) remove the wire from the spark plug, thoroughly
inspect the brush for any damage, and repair damage
before restarting and operating the brush.
.4 If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the cause.
Vibration is generally a warning of trouble.
.5 Stop the engine (motor) whenever you leave the
operating position, before making any repairs,
adjustments or inspections.
.6 Take all possible precautions when leaving the
machine unattended. Disengage the drive, lower the
attachment, set the parking brake, stop the engine and
remove the key.
.7 Before cleaning, repairing or inspecting, make
certain all moving parts have stopped. Disconnect the
spark plug wire and place the wire away from the plug
to prevent accidental starting.
.9 Do not operate across the face of slopes. Exercise
extreme caution when changing direction on slopes. Do
not attempt to clear steep slopes.
.10 Never operate the brush without provided guards,
plates or other safety protective devices in place.
.11 Never operate the machine at high transport speed
and use care when backing up!
.12 Never allow anyone in front of the unit.
.13 Disengage power to the brush when transporting or
not in use.
.14 Never operate the power brush without good
visibility or good light.
While operating, ALWAYS attach
the clip end of the Tether Cord
to your belt, until you dismount
from the ATV. The switch the
cord is attached to will shut off
the engine if pulled deliberately
or by inadvertent dismount from
the ATV seat.
DANGER
Failure to observe the following safety instructions
could result in serious injury and or

Quad Power Brush
Operators Manual – Version 06
2

3. SET-UP & OPERATION
-i- BRUSH MOUNTING
*Refer to the Power Unit operator’s manual for
instructions on assembly of the Power Unit.
1. Loosen the motor plate on the Power Unit (Refer to
Power Unit Manual for illustration)
2. Take the belt, slide over pulley on broom and the
upper pulley on the Interframe (Figure 3-1).
Figure 3- 1
3. Tighten the motor plate on the Power Unit
3 Engage both locking clips on the brush (one on
each side) as shown in Figure 3-2. 


Figure 3-2
5. Attach the winch cable to the last chain link to
prevent the brush from hitting the ATV when winch
is reeled in. Depending on winch location on the
ATV, a higher lift is required to use the second link,
but only if it cannot interfere with the ATV when
lifted.
-ii- ANGLE ADJUSTMENT
Manual
Remove Pivot stop pin (shown in Fig 3-2) and manually
adjust angle by rotating brush to desired angle and
reinsert pin
Electrical Pivot (Option)
An electrical pivot option is available and is setup as
shown in the Figure 3-3
1. Bracket. 2. Actuator. 3. Washers. 4. Bracket. 5. Pin
Figure 3-3
Attach the supplied wiring harnesses to the ATV as
shown in Figure 3-4.
Figure 3-4
Attach the switch to the front rack of the ATV with the
bracket.
Pivot Sto
p
Pin
NOTE: Identify with the
battery of the ATV to ensure
which are the Positive (+)
and the Negative (-) poles.
Lockin
g
Cli
p

Quad Power Brush
Operators Manual – Version 06
3
WHEN IN USE: Attach the clip end of the Tether Cord
to your belt, until you dismount the ATV. The switch the
cord is attached to: will shut off the engine if pulled
deliberately or by inadvertently dismounting from the
ATV seat.
Gage Wheels
1. The gage wheels (one on each side) are to be used
on surfaces that are not hard enough for the full
weight of the brush, such as sweeping leaves on
grass. The wheels are not needed for hard
surfaces, such as concrete or asphalt.
2. When not used: the gage wheel assemblies can be
removed from the unit OR stored upside down in
the same holder and tightened (refer to procedure
3).
3. Lift the Brush and adjust the wheels to the desired
height, depending on the degree of aggressive
desired. Secure the gage wheels with the offset
locking pins (Figure 3-5) to achieve proper locking
tightness.
Figure 3-5
GENERAL OPERATION
1. Start brush engine and warm up at LOW RPM.
2. Increase engine RPM to desired speed and
start operating. Refer to the Power Unit Manual
for illustrations and operation of throttle
controls).
3. Operate brush so wind blows debris away from
operator, engine and power unit.
4. For a longer lasting brush; take note of the
following:
a) More pressure does not produce a better sweep
b) A level brush lasts longer.
c) The faster the ground speed, the faster the
brush will wear.
d) More aggressive brush down pressure will
reduce brush life.
5. Drive at low speed.
6. When climbing curbs or loading brush on trailer,
raise brush to maximum height and drive slowly.
The bristles might come in contact with curb or
trailer ramp.
STORAGE
1. Keep all nuts, bolts and screws properly tightened.
This maintains the unit in good working condition.
2. Remove weight from brush bristles by putting
blocks under the frame and setting up gage wheels
to maintain brush to floor clearance.
3. Refer to Power Unit manual on storage instruction
for the Power Unit
MAINTENANCE
1. Refer to the engine manual for servicing and
lubrication specifications and intervals.
2. Clean engine air cleaner frequently (hourly, if
necessary, if subject to a lot dust).
3. Clean debris from engine and gearbox area after
each use.
4. The gearbox is sealed and therefore the oil level
cannot and is not required to be checked.
5. Bristles wear off after time and will be in need of
replacement:
a. Disconnect the roller chain that attaches the
gearbox to sprocket on the brush.
b. Remove the bolted front shield for easier access,
if desired, but not necessary.
c. Remove the bearing (Figure 3-5) on each side of
the brush and slide out the shaft.
d. Remove bolts from bristle shaft and replace all
bristles at once.
NOTE: Refer to pages 10 to 13 of the Parts
Replacement Section of this manual.

Quad Power Brush
Operators Manual – Version 06
4
NOTE: Bristles must be replaced all at once or
uneven sweeping will occur. The longer bristles
will wear off faster.
6. Replacing and Adjusting belt and belt tension:
a. Belt tension is determined by the position of
the motor on the Power Unit. To adjust the
tension; loosen the motor bolts on the Power
Unit and slide the motor until proper tension is
achieved.
b. To replace the belt; perform the previous step
and unlock locking clips as shown in Figure 3-
2 and replace belt. See Figure 3-7, Belt Drive
Schematic.
NOTE: As the engine is moved rearward on the
power unit, the spring loaded idler pulley (under
the gearbox of the Power Brush) will come under
greater tension.
Figure 3-6
7. Servicing the roller chain that drives the rotor:
a.To replace the roller chain, remove the bolts
that hold the springs on the idler. Remove
springs, Figure 3-6.
b.Find the connector link on the chain and
disconnect.
c. Roll chain out and insert the replacement.
d.For easier access to the sprocket on the rotor,
remove the top cover on the brush assembly
before replacing chain.
Figure 3-7: Belt Drive Schematic
CHAIN DRIVE SCHEMATIC
Tension Spring and Idler Sprocket

Quad Power Brush
Operators Manual – Version 06
5
4. REPLACEMENT PARTS
The following pages contain parts
illustrations and replacement part numbers
for all components for the Quadivator Power
Brush. At the time of printing, some of the
minor parts in the manual may become
outdated.
To obtain replacement parts, please contact
your Quadivator Dealer for service. To
locate the nearest dealer, please contact a
Quadivator Representative using the contact
information at the beginning of the manual.
When ordering parts – please have the
following information on hand:
- Part Number you are looking for.
- Model Number and Serial Number
of the machine.
- Quantity required.
To ensure warranty support for your
Quadivator, please fill out the Warranty
Registration Card located at back of the
Operator’s Manual.
Power Brush Sub-assemblies
Electrical Brush Pivot Option
(89900):
ITEM QTY. PART DESCRIPTION
1 1 89906 Bracket - Actuator Base
2 1 86031 Actuator
3 3 FW.5N Flat Washer 1/2 SAE
4 1 89915 Weld't -Actuator Rod End
5 1 CTP.125x1 Cotter Pin 1/8 x 1
6 1 89930 Actuator Switch/Wiring Harness (not shown)

Shields and Sub Assemblies
9
12
43
45
26
52 59
35
Rear SubAssembly - See Pages 8 & 9
Rotor Sub Assembly - See pages 10, 11
Front Sub Assembly - See pages 12 & 13
54
53 52
59
32
Operators Manual - Version 06
Quad Power Brush
6

ITEM
Qty
PART DESCRIPTION
1 2 88540
Spacer - Bushing
2 1 88574
Idler Pulley - 3"
3 1 88579
UNMW - Flange Bearing
4 3 88651
Spring, Extension - Tensioner Arm
5 1 89075B
Weld't -Pulley 4.5" 'B' x 24 Bore
6 1 89529
Spacer - Pulley
7 1 89550 Gearbox, Worm - 10:1 RatiO
8 1 89705
W.A. - Mounting Frame
9 1 89710
Sub Assy -Brush Rotor
10 1 89715 W.A. - Frame, Brush
11 1 89725A
W.A. - Sweeper Arm, LH
12 1 89730
W.A. - Hood, Sweeper
13 1 89734
Drive Shaft - Sweeper
14 1 89740 Weldment - Anchor Pivot
15 1 89745 Weldment - Brace, Pivot
16 1 89751
Bushing - Gearbox Mount
17 1 89755A
W.A. - Sweeper Arm, RH
18 1 89760B
Sprocket - #50 X 25t
19 1 89788
Tube - Spacer
20 1 89812
Pin - Pivot Stop
21 1 89813
Key -5/16 x 100
22 1 89814
Bushing -Spacer-Sprocket
23 1 89830 Weld't-Rotor Frame Backbone
24 1 89846 Pin-Lift
25 1 89852 Thrust Washer -UHMW
26 2 89855A
Assy - Gage Wheel -Optional
27 1 89860 Stud Bolt -3/8-16 NC x 80
28 2 89863 Latch
29 2 89865
Spring-Comp-.625 OD x 2.75FL x .054Wire
30 2 89887
Idler Sprocket 50 Pitch x 13t -17mm ID
31 2 89889 Bracket - Tensioner Mount
32 1 89909 Shield - Belt -Rubber
33 1 89910
Chain Assy - Lift
34 1 89935 Weld't -Idler Pivot
35 2 QRP .313x2-30 Pin - Quick Release
36 3 LW.313 Lockwasher-5/16
37 4 HB.375x1.25 Hex Head Bolt 3/8-16 X 1 1/4
38 1 HB.375x1.5 Hex Head Bolt 3/8-16 X 1 1/2
39 4 RP.125x1 Roll Pin- 1/8 x 1
40 2 FW.313 Flat Washer 5/16 Std
41 2 HB.313x.75 Hex Head Bolt 5/16-18 X 3/4
42 8 CB.375x1
Carriage Bolt 3/8 x 1
43 14 CB.25x3/4
Carriage Bolt 1/4 x 3/4
44 2 HB.25x1.5 Hex Head Bolt 1/4-20 X 1 1/2
45 1 89809A Chain -#50 x 105P w/ Conn
46 2 HB.25x1 Hex Head Bolt 1/4-20 X 1
47 3 70924280
Pop Rivet, Aluminum 1/8 Dia x .390 Long
48 1 FW.75N Flat Washer 3/4 SAE
49 1 HB.375x1.75 Hex Head Bolt 3/8-16 X 1 3/4
50 1 HBm8x20 Hex Bolt M8 x 1.25 x 20
51 6 TLN.375
Nut, Hex Top Lock 3/8-16 UNC Gr 5 Zn Plt
52 5 14618
Brg Unit-Prssd Stl Hsng SBPFL205-16
53 10 CB.313x3/4
Carriage Bolt 5/16 x 3/4
54 19 FHN.25
Flange Lock Nut-1/4 NC Unitorque
55 1 HB.375x2 Hex Head Bolt 3/8-16 X 2
56 3 FlatWasher Flt Fndr Wshr 3/8"IDx1.25"ODx.125 Thk
57 26
Nut-FlangLock Flange Lock Nut-3/8 NC Unitorque
58 12 hexheadbolt Hex Head Bolt 3/8-16 X 1
59 10
Nut-FlangLock Flange Lock Nut, Unitorque 5/16 NC
Operators Manual - Version 06
Quad Power Brush
7

45
44
44
24
2
38
60
59
47
51
43
57
3
2
*
51
32
16
21
40
45
57
46
50
1
25
26
19
10
44
51
22
11
54
52
13
18
9
57
51
33
17
4
8
59
53
56
51
51
45
46
50
5
44
* Refer to page 16 for parts breakdown
of the gearbox.
Gearbox Assembly
Quad Power Brush
Operators Manual - Version 06
8

Operators Manual - Version 06
Quad Power Brush
9
ITEM Qty PART DESCRIPTION
1 5 14618 Brg Unit-Prssd Stl Hsng SBPFL205-16
2 2 88540 Spacer - Bushing
3 1 88574 Idler Pulley - 3"
4 1 88579 UNMW - Flange Bearing
5 3 88651 Spring, Extension - Tensioner Arm
6 1 89702 Shim, Power Brush Arm
7 3 70924280 Pop Rivet, Aluminum 1/8 Dia x .390 Long
8 1 89075B Weld't -Pulley 4.5" 'B' x 24 Bore
9 1 89529 Spacer - Pulley
10 1 89550 Gearbox, Worm - 10:1 Ratio
11 1 89705 W.A. - Mounting Frame
12 1 89710 Sub Assy -Brush Rotor
13 1 89715 W.A. - Frame, Brush
14 1 89725A W.A. - Sweeper Arm, LH
15 1 89730 W.A. - Hood, Sweeper
16 1 89734 Drive Shaft - Sweeper
17 1 89740 Weldment - Anchor Pivot
18 1 89745 Weldment - Brace, Pivot
19 1 89751 Bushing - Gearbox Mount
20 1 89755A W.A. - Sweeper Arm, RH
21 1 89760B Sprocket - #50 X 25t
22 1 89788 Tube - Spacer
23 1 89809A Chain -#50 x 105P w/ Conn
24 1 89812 Pin - Pivot Stop
25 1 89813 Key -5/16 x 100
26 1 89814 Bushing -Spacer-Sprocket
27 1 89830 Weld't-Rotor Frame Backbone
28 1 89846 Pin-Lift
29 1 89852 Thrust Washer -UHMW
30 2 89855A Assy - Gage Wheel -Optional
31 1 89860 Stud Bolt -3/8-16 NC x 80
32 2 89863 Latch
33 2 89865 Spring-Comp-.625 OD x 2.75FL x .054Wire
34 2 89887 Idler Sprocket 50 Pitch x 13t -17mm ID
35 2 89889 Bracket - Tensioner Mount
36 1 89909 Shield - Belt -Rubber
37 1 89910 Chain Assy - Lift
38 1 89935 Weld't -Idler Pivot
39 15 CB.25x3/4 Carriage Bolt 1/4 x 3/4
40 10 CB.313x3/4 Carriage Bolt 5/16 x 3/4
41 8 CB.375x1 Carriage Bolt 3/8 x 1
42 21 FHN.25 Flange Lock Nut-1/4 NC Unitorque
43 10 FHN.313 Flange Lock Nut, Unitorque 5/16 NC
44 32 FHN.375 Flange Lock Nut-3/8 NC Unitorque
45 3 FNW.375x1.25X.12 Flt Fndr Wshr 3/8"IDx1.25"ODx.125 Thk
46 2 FW.313 Flat Washer 5/16 Std
47 1 FW.75N Flat Washer 3/4 SAE
48 2 HB.25x1 Hex Head Bolt 1/4-20 X 1
49 2 HB.25x1.5 Hex Head Bolt 1/4-20 X 1 1/2
50 2 HB.313x.75 Hex Head Bolt 5/16-18 X 3/4
51 12 HB.375x1 Hex Head Bolt 3/8-16 X 1
52 3 HB.375x1.25 Hex Head Bolt 3/8-16 X 1 1/4
53 2 HB.375x1.5 Hex Head Bolt 3/8-16 X 1 1/2
54 1 HB.375x1.75 Hex Head Bolt 3/8-16 X 1 3/4
55 1 HB.375x2.25 Hex Head Bolt 3/8-16 X 2
56 1 HBm8x20 Hex Bolt M8 x 1.25 x 20
57 3 LW.313 Lockwasher-5/16
58 2 QRP .313x2-30 Pin - Quick Release
59 3 RP.125x1 Roll Pin- 1/8 x 1
60 1 RP.125x1.25 Roll Pin- 1/8 x 1 1/4

30
27
20
44
43
1
30
58
39
32
17
12
A
Quad Power Brush
Operators Manual - Version 06
10
53
2
34
2
SCALE 2 : 15
DETAIL A
23
44
5
60
44
1
43
40
Some components hidden for clarity.
View from Rear -
Some components hidden for clarity.
27
37
28
42
49
36
7
44
31
44
2
34
2
42
35 44
48
5
View from Front
-
Brush Assembly

Operators Manual - Version 06
Quad Power Brush
11
ITEM Qty PART DESCRIPTION
1 5 14618 Brg Unit-Prssd Stl Hsng SBPFL205-16
2 6 88540 Spacer - Bushing
3 1 88574 Idler Pulley - 3"
4 1 88579 UNMW - Flange Bearing
5 3 88651 Spring, Extension - Tensioner Arm
6 1 89702 Shim, Power Brush Arm
7 3 70924280 Pop Rivet, Aluminum 1/8 Dia x .390 Long
8 1 89075B Weld't -Pulley 4.5" 'B' x 24 Bore
9 1 89529 Spacer - Pulley
10 1 89550 Gearbox, Worm - 10:1 RatiO
11 1 89705 W.A. - Mounting Frame
12 1 89710 Sub Assy -Brush Rotor
13 1 89715 W.A. - Frame, Brush
32 1 89725A W.A. - Sweeper Arm, LH
17 1 89730 W.A. - Hood, Sweeper
16 1 89734 Drive Shaft - Sweeper
17 1 89740 Weldment - Anchor Pivot
18 1 89745 Weldment - Brace, Pivot
19 1 89751 Bushing - Gearbox Mount
20 1 89755A W.A. - Sweeper Arm, RH
21 1 89760B Sprocket - #50 X 25t
22 1 89788 Tube - Spacer
23 1 89809A Chain -#50 x 105P w/ Conn
24 1 89812 Pin - Pivot Stop
25 1 89813 Key -5/16 x 100
26 1 89814 Bushing -Spacer-Sprocket
27 1 89830 Weld't-Rotor Frame Backbone
28 1 89846 Pin-Lift
29 1 89852 Thrust Washer -UHMW
30 2 89855A Assy - Gage Wheel -Optional
31 1 89860 Stud Bolt -3/8-16 NC x 80
32 2 89863 Latch
33 2 89865 Spring-Comp-.625 OD x 2.75FL x .054Wire
34 2 89887 Idler Sprocket 50 Pitch x 13t -17mm ID
35 2 89889 Bracket - Tensioner Mount
36 1 89909 Shield - Belt -Rubber
37 1 89910 Chain Assy - Lift
38 1 89935 Weld't -Idler Pivot
39 15 CB.25x3/4 Carriage Bolt 1/4 x 3/4
40 10 CB.313x3/4 Carriage Bolt 5/16 x 3/4
41 8 CB.375x1 Carriage Bolt 3/8 x 1
42 21 FHN.25 Flange Lock Nut-1/4 NC Unitorque
43 10 FHN.313 Flange Lock Nut, Unitorque 5/16 NC
44 32 FHN.375 Flange Lock Nut-3/8 NC Unitorque
45 3 FNW.375x1.25X.12 Flt Fndr Wshr 3/8"IDx1.25"ODx.125 Thk
46 2 FW.313 Flat Washer 5/16 Std
47 1 FW.75N Flat Washer 3/4 SAE
48 2 HB.25x1 Hex Head Bolt 1/4-20 X 1
49 2 HB.25x1.5 Hex Head Bolt 1/4-20 X 1 1/2
50 2 HB.313x.75 Hex Head Bolt 5/16-18 X 3/4
51 13 HB.375x1 Hex Head Bolt 3/8-16 X 1
52 3 HB.375x1.25 Hex Head Bolt 3/8-16 X 1 1/4
53 1 HB.375x1.5 Hex Head Bolt 3/8-16 X 1 1/2
54 1 HB.375x1.75 Hex Head Bolt 3/8-16 X 1 3/4
55 1 RP.125x1.25 Roll Pin- 1/8 x 1 1/4
56 1 HBm8x20 Hex Bolt M8 x 1.25 x 20
57 3 LW.313 Lockwasher-5/16
58 2 QRP .313x2-30 Pin - Quick Release
59 3 RP.125x1 Roll Pin- 1/8 x 1
60 1 HB.375x2.25 Hex Head Bolt 3/8-16 X 2

Brush Rotor Sub Assembly
89710
4
2
9
10
12
7
8
3
6
12
4
10
9
1
5
11
1
Optional Gage Wheel Sub Assembly
89855A
13
10
12
9
11
8
7
7
4
3
7
5
7
2
6
1
ITEM QTY. PART DESCRIPTION
1 28 88669
Wafer, Blue Poly Conv.
2 1 89517
Sprocket - 44 Tooth x 50 Pitch
3 1 89720 Weld't -Brush Rotor
4 2 89771 Chain Guide-Circular
5 2 89793 Plate - Retainer, Waffle
6 1 89833
Shim Spacer -Chain
7 1 89845
Weld't -Spacer Ring
8 3 89860 Stud Bolt -3/8-16 NC x 80
9 6 FHN.375
Flange Lock Nut-3/8 NC Unitorque
10 6 FW.375 Flat Washer 3/8 Std
11 6 HB.375x1 Hex Head Bolt 3/8-16 X 1
12 6 HN.375 Hex Nut 3/8-16 UNC
13 6 LW.375 Lockwasher-3/8
ITEM 89855A/QTY. PART DESCRIPTION
1 2 88540
Spacer - Bushing
2 1 89753 Washer - Caster
3 1 89765A W.A. - Caster Wheel Mount
4 1 89775B
Weld't -Gage Wheel
5 1 89822
Tube -Bearing Spacer -Castor
6 1 89823
Assy-Rubber Wheel
7 4 89824
Bearing 6003-2RS-AAB
8 1 FHN.375
Flange Lock Nut-3/8 NC Unitorque
9 1 FNW.375x1.25X.12 Flt Fndr Wshr 3/8"IDx1.25"ODx.125 Thk
10 1 HB.375x1 Hex Head Bolt 3/8-16 X 1
11 1 HB.375x5 Hex Head Bolt 3/8-16 X 5
12 1 LW.375 Lockwasher-3/8
Operators Manual - Version 06
Quad Power Brush
12

15
17
4
17
11
12
19
3
16
8
9
2
17
1
10
1
19
1817
13
17
14
To Power Unit Engine Pulley
To Power Brush Pulley
16
4
Short Interframe Assembly
89250-06
5
2
6
7
16
ITEM 89250-06/QTY. PART DESCRIPTION
1 2 19-5-91
Bushing -Oilite 12.7ID x 16OD x 9.4 Long
22 86803
Ratchet Strap -05500 1 x 6
3 2 88403 Washer - Retainer
4 2 88545
Spacer - Bushing
5 1 88665
Decal-Quadivator Corp-1.75 x 8.5"
6 1 88666 Decal - Serial Plate Foil (1 5/8 x 3.00")
7 1 88667 Decal - Mylar Overlay, Frosted
81 89240A Weldment - Inter-Frame, short
9 1 89245
Assembly - Bumper Pad
10 1 89290
Weld't - Pulley Mount Swing Arm
11 1 89315B
Pulley -Double Idler Weld't -4.5&8
12 1 89318
Bushing -Spacer -Dbl Pulley
13 2 89442
Lug, Ratchet Strap Base
14 1 89523 V Belt -B116, Kevlar (USA) (4404)
15 1 89530 V Belt -B133, Kevlar(7-8727)
16 2 89824
Bearing 6003-2RS-AAB
17 8 FHN.5
Flange Lock Nut-Unitorque -1/2-13NC
18 4 HB.5x3 Hex Head Bolt 1/2-13 X 3
19 3 HB.5x3.5 Hex Head Bolt 1/2-13 X 3 1/2
20 3 LCT.04x11 Tie Wrap .04 x .17 x 11 in 35 Lbs-Black
Operators Manual - Version 06
Quad Power Brush
13

Long Interframe Assembly
89450-06
To Power Unit Engine Pulley
To Power Brush Pulley
13
2
8
4
15
416 10
11
5
18
3
16
16
1
1
18
12
17
16
17
15
7
9
2
14
6
13
ITEM 450-06Manual/QTY. PART DESCRIPTION
1 2 19-5-91
Bushing -Oilite 12.7ID x 16OD x 9.4 Long
22 86803
Ratchet Strap -05500 1 x 6
3 2 88403 Washer - Retainer
4 2 88545
Spacer - Bushing
5 1 88645 Belt B225 - Blower Drive
6 1 88666 Decal - Serial Plate Foil (1 5/8 x 3.00")
7 1 88667 Decal - Mylar Overlay, Frosted
8 1 89245
Assembly - Bumper Pad
9 1 89290
Weld't - Pulley Mount Swing Arm
10 1 89315B
Pulley -Double Idler Weld't -4.5&8
11 1 89318
Bushing -Spacer -Dbl Pulley
12 1 89440
Weldment - Inter-Frame-Long
13 2 89442
Lug, Ratchet Strap Base
14 1 89545 V Belt- B136, Kevlar
15 2 89824
Bearing 6003-2RS-AAB
16 8 FHN.5
Flange Lock Nut-Unitorque -1/2-13NC
17 4 HB.5x3 Hex Head Bolt 1/2-13 X 3
18 3 HB.5x3.5 Hex Head Bolt 1/2-13 X 3 1/2
Operators Manual - Version 06
Quad Power Brush
14