QualGear QG-PRO-PM-50-B User manual

For a perfect viewing experience, make adjustments
by loosening the screws slightly on the projector mount and
tighten them to secure the position with an allen key.
Roll ±8°, Pitch ±20°, Rotate 360°
Adjustments
4
CAUTION!
Do not exceed the maximum rated weight
specified. Otherwise, serious injury or
property damage may occur.
32kg
(70lbs)
RATED
5 Year Limited Warranty
Version August 2017
5 Year Limited Warranty
QG-PRO-PM-50-B
QG-PRO-PM-50-W
HEAVY!
Use an assistant for this step.
IMPORTANT!
Do not loosen screws all the way when making adjustments, this will disconnect the
parts and may cause injury or property damage.
20
20
8
8
1.5" NPT Pipe
(not included)
Version August 2017
Scan the QR Code™ below
for more info about this product:

y.Please read the entire installation manual before you start installation and assembly.
IMPORTANT: Installers must verify that the supporting surface will safely
support the combined weight of the equipment and all attached hardware
and components.
Do not begin to install your QualGear
product until you have read and understood
all the instructions and warnings contained
in this installation manual. If you have
any questions regarding the instructions,
for US customers please contact
QualGear customer support via email at
[e-mail]. For all international
customers, please contact your local
distributor.
This product should only be installed by
someone of good mechanical aptitude, has
experience with basic building construction,
and fully understands these instructions.
This product was designed to be installed
and utilized only as specified in this manual.
Improper installation of this product may
cause damage or serious injury. QualGear is
not liable for the improper use or installation
of its products.
Make sure that the supporting surface
will safely support the combined load of the
equipment and all attached hardware and
components.
Always use an assistant or mechanical
lifting equipment to safely lift and position the
equipment.
Tighten screws firmly, but do not over
tighten. Over tightening can damage the
items, greatly reducing their holding power.
ALL QUALGEAR products are intended
for indoor use only and any outdoor use voids
the limited warranty. For warranty information,
please visit:
http://www.qualgear.com/warranty.php
Never exceed the maximum rated weight
specified in this manual.
All hardware must be used at the
designated points in the installation
instructions to prevent property damage
and/or personal injury.
This product was designed to be
compatible with all standard 1.5" NPT
pipes.
WARNING
Maintenance
Please check that the ceiling projector mount is secure and safe to use at regular intervals. If you
have any questions regarding any of the instructions or warnings, please contact your local distributor
(OR) contact QualGear technical support via email at [e-mail].
1 2
Parts Checklist
Hardware Package
IMPORTANT: Before starting installation, please check that all parts shown in this checklist
are included. If any parts are missing or damaged, contact your local distributor or
[email protected] for replacement parts and do not start assembly and installation
until you receive all the parts.
Allen Key
C (x1)
Security
Security
M4 x 10mm
Screws
F (x4)
M3 x 8mm
Screws
E (x4)
M6 x 10mm
Screws
H (x4)
Set Screws
J (x2)
Projector Assembly Hardware Package (S3103-1 / S3103-4)
Projector Mounting Hardware Package (S3706-1 / S3706-4)
M4-M6
Allen Key
D (x1)
M5 x 10mm
Screws
G (x4)
Washers
I (x4) M5 x 10mm
Screws
K (x4)
Projector Plate
B (x1)
Projector Mount
A (x1)
Adapter
Extension Brackets

Connecting the Pipe to the Projector Plate
1Making Adjustment for Mounting 2
34
To connect a 1.5" NPT pipe to the projector plate, twist the
male threaded end of the pipe into the female thread on
the projector plate.
Allen Key
(C)
Set Screws (J)
Front
1.5" NPT Pipe
(not included)
Projector Plate
Using allen key (C), insert and tighten set screws (J)
to secure the position.
Using allen key (D), insert screws (K) to the adapter as
shown and leave a gap. Do not tighten all the way.
Screws (K)
Allen Key (D)
Depending on your projector, adjust the extension brackets on the projector mount (A) accordingly
by using allen key (D).
If your projector model has three mounting holes only, please remove the fourth extension bracket
using allen key (D).
Allen Key (D)
gap
TIP
Do not tighten the screws,
leave a gap for mounting
on the next step.
WARNING
Installers are responsible to provide hardware for other types of mounting situations.
 Installers must verify that the supporting surface will safely support the combined
weight of the equipment and all attached hardware and components.
NOTE Do not use screws (G).
The length and height of the extension brackets can be changed by sliding in and out, or up and down.
TIP
Extension Brackets
Adapter

Attaching the Projector Mount to the Projector
3
Slide projector assembly into the
projector plate until you hear a click.
Depending on your projector, use the appropriate screws (E/ F/ G/ H) and then
attach the projector mount to the projector and tighten with allen key (C or D).
Make sure arrow points to
the projector screen Projector
(not included)
Tighten the screws (K) using allen key (D)
as shown on the right.
Screws (E/ F/ G/ H)
Allen Key (C/ D)
Washers (I)
For screws (E or F) only
NOTE Use washers (I) only when
using screws (E or F).
Projector
(not included)
Allen Key (D)
Projector Plate
Click!
5 6
TIP